Dlink 625 Not Showing Connections?
Jan 7, 2012
I have 3 pc's connected to the router, hard wired in using cat5. When plugging the cable into the router, the router port on front lights up. If I put it in the 3 port, the 3 lights up. If I put it in the #1 port, the port 1 lights up. I believe it means the pc is being detected by the router. If I go to the ip addy for the router (192.168.0.1), it is only showing the pc I am on. The other 2 pc's are not appearing, and they are not able to access the network. If I add a wireless item, like my Iphone, it is detected on the network right away.This only started this morning. I have restarted the pc's, restarted the router, reset the router, moved the cables to different ports, and swapped the cables from one pc to another. The only pc that gets detected in all of this is the one I am on. Regardless of port/ wire.
View 1 Replies
ADVERTISEMENT
Mar 28, 2012
I'm running XP and have Bell-Aliant modem SIEMENS Gigaset SE567 running to DI-624 router. It has been working for years but after the internet was down in the area for most of the day, it has failed to reset. I've done the usual un-plug/wait/replug routine a few times but cannot connect. I can connect directly through the SIEMENS but when I introduce the DI-624 back into the mix, I'm not able to connect to the internet. How do I make it happen. I'm not tech savvy so go slow.
View 1 Replies
View Related
Aug 19, 2012
I have a desktop PC where the only internet connection is via a 'USB mobilebroadband dongle'.I have connected the PC via ethernet cable to the ethernet port on a d-link wifi router (which isn't connected to the internet).I'd like to be able to connect other non-PC devices (eg my mobile phone) to the router via wifi in order to connect to the internet.To do this, I gather that one possible solution is to bridge the LAN (not connected to internet) and dongle (connected to internet) connections.My first problem is that in 'Network Connections', only my USBdongle connection is shown (see pic) - there is no icon for the LAN/ethernet. In device manager, the "Atheros AR5007EG Wireless NetworkAdapter" and "Realtek PCIe FE Family Controller" are both showing without any ?
Other info:I'm running Windows 7 Home Premium 64 on a HP Pavilion All-in-one MS200 desktop.
View 6 Replies
View Related
Jan 15, 2011
i am unable to connect wirelessly my wireless connection is not showing under the available connections and i can onhy connect hardwired via my router i have done simple troubleshooting with no results i have also tried to go to routerlogin.com and .net and i cant access them i have also done the pinging and everything seems to be in order what are my next steps
View 9 Replies
View Related
Jul 13, 2011
Is there any way to make it so that my computer has two internet connections, so to my router it looks my computer is two separate computers, and would this increase my speed, since my router is made for up to 15 connections and has only 300mb/s to give out, so [would]each computer is[be] only limited to 20mb/s? As of now I have a dlink xtreme-n DWA-552 adapter in my computer.
View 2 Replies
View Related
Nov 25, 2012
Two days ago I booted my laptop and found that I'm not able to connect to the internet via LAN. It didn't detect a connection, even though my cable was plugged in. It was able to detect the wifi networks from my neighbors, but that's not an option, i need the LAN. I changed absolutely nothing,nno updates, downloads, ... It just came out of nowhere.I already eliminated a cable problem, the laptop from my roommate was able to connect without a problem.When I plug the cable in mine, the lights on the port flicker, making me believe that it's not a problem with my port either.it's definitely a computer problem, but I'm not sure if it's my computer or my network adapter that's being a PITA.When I go to the Device Manager, the network adapter (broadcom 802.11g) is fine, no red x or yellow exclamation point. i have already tried turning it on and off, and uninstalling and then rebooting, no avail.
View 6 Replies
View Related
Nov 23, 2011
Just bought myself a TP-Link WN722N Wirless Adapter. Currently I have a Netgear WNA3100 connected which works fine but I to use the TP-Link to connect to a second network simultaneously.Here's the problem.The drivers installed just fine for the TP-Link adapter. Windows shows that its connected as a USB device (USB2.0 WLAN) and Network & Sharing Centre shows it is being "Wireless Network Connection 4"(The Netgear one shows as "Wireless Network Connection 2")However, when i try to use the TP-Link one to connect to a network, it doesn't show up in the "Network Connections" menu on the Taskbar, and when i disconnect the Netgear one it says that it can't find any wireless connections at all; note that "Network & Sharing Centre" still shows the TP-Link Adapter as being connected to the PC).Tried Reinstalling the TP-Link Software, updating it, etc. Restarted PC. Disabled Netgear connection. Physically Disconnected Netgear Adapter and still no luck.
View 2 Replies
View Related
Nov 29, 2011
I have a cisco 5520 running as IPsec concentrator. On the ASDM homepage is shows like 31 VPN connected. But if I go to Monitor > VPN is show only 18. Then if I use SSH using sh crypto command it shows the same number as on the Monitor > VPN sections. I am running 8.3(1) and ASDM 6.3(1).
View 8 Replies
View Related
Feb 4, 2011
My Ethernet is not showing up in device manager or Network Connections. I've checked the bios and it is enabled. I've also tried to install the drivers, but at the end of the install this error message pops up " the Realtek Network Controller was not found. If Deep sleep mode is enabled please plug the cable"
View 1 Replies
View Related
Sep 5, 2012
So I just installed Windows Server 2003 64 bit on an older HP Proliant DL360 G5 and am trying to connect it to my network but neither of the 2 NIC's are showing up under Network Connections... the only option I am given is the ''Add Network Places Wizard''.
I have an ethernet cable plugged into NIC 1 and the LED's work so I know it's not a bad NIC card- do I have to download drivers for the NIC? Do I download them to a USB/CD and then just boot from that?
View 1 Replies
View Related
Apr 25, 2012
I have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655
Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
View 6 Replies
View Related
Feb 5, 2011
my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies
View Related
Jul 3, 2011
So far I have tried doing a factory reset, power cycling, upgrading my firmware, and changing my channel [even though there weren't any interfering networks on the same channel in my area].
This problem started a while ago and has been going on for several months now. I will lose access to the internet for a brief period of time [1-2 seconds], but this is very annoying. I will exit conversations on MSN, downloads will stop sometimes, and it is virtually impossible to play online multiplayer games since I keep losing connection every five minutes or so.
The connection works just fine when I connect my modem directly to my PC.
View 4 Replies
View Related
Jan 3, 2012
I have two d link 604 and want to connect both together so that any pc connected to the repeater can connect to the internet. I am running win xp sp3,p4,2gb,asus p4p800-vm with all updates and firmware of router updated.
View 7 Replies
View Related
Jan 20, 2011
About 3 or maybe 4 years ago I bought a Dlink DIR-655 wireless router.On the box it listed it as an Xtreme N Gigabit Router, Wireless N (Draft N). I've had two Windows PCs connected to this router by Cat5 with "Intel 82562V-210 10/100 Network Connection" NICs on each set to "Auto detect". The link speed on the NICs show as 100Mbps.Also, I have an MBP and a Windows laptop that connects to this router at times, both with built-in wireless cards.I have Insight Cable and a 20Mbps download and 1.38 upload speeds.This router has worked great for the past years. Since it was getting a little old, I thought I would buy another just like it to have when this one defaults.I ordered a replacement from Amazon. The picture of the router at Amazon was the same as the one I have now.When the router arrived, it was a Dlink DIR-655; however, the router had a different faceplate and larger lights.On the box it listed it as "Xtreme N Gigabit Router". Also listed was N+ 300.
When I set the new DIR-655 up for my LAN and wireless, everything worked OK.However, I noticed the link speed on the NICs had dropped to 10Mbps.I can disable the NIC and then enable, or, unplug and plug in the Cat5 cable, and it will connect at 100Mbps for about 5 seconds and then revert back to 10Mbps.I returned the router to Amazon and purchased another just like it from Office Depot.The same problems are back.I have used the router set-up disk and have done a manual set-up. I cannot get the NICs to connect to the router above 10Mbps.I have turned off wireless, made different settings throughout the router and nothing works.I can set the NICs to 100Mbps full duplex and I get 1.5Mbps download speeds. If I set them to 100 half duplex, I might get 5Mbps.Believe me; I have just about changed every setting on this router with no success. I've turned the firewall, QoS off then on, wireless off and on, put one PC outside the router, but nothing works. Also, firmware is up to date.When I connect my PC direct to Insight modem or connect the original DIR-655, I get 100Mbps on the NIC and 20+Mbps download speed.I cannot get the NICs to connect above 10Mbps on this "new DIR-655" router.
View 9 Replies
View Related
Mar 19, 2011
I am having a terrible time getting a good signal from my DLink-DIR655 router to my Samsung HDTV with a linkstick to have access to the apps like Netflix. My router is located about 60 feet away but the signal is sufficient to connect to my laptop located in the same room as the tv. I have been told the router should be no more than 20 feet from the tv and have tried a DWL-G710 range extender but that doesn't work.
View 1 Replies
View Related
Jun 19, 2011
I've bought a new note book and i can't connect to my Dlink router, it won't accept my security key
View 3 Replies
View Related
Mar 7, 2012
I have already successfully upgraded the firmware to DD-WRT with no problems.What I want to do is have the D-Link DIR-601 Router set as a Repeater Bridge because I am trying to expand my wireless signal to dead spots in the house.I have NO SECURITY enabled on my NetGear Router and I am still unable to successully setup the D-link DIR-601 Router as a Repeater Bridge.
View 2 Replies
View Related
Nov 18, 2011
I have a computer connected through wifi to the internet.I then turn on the computer into ICS mode and connect that to my PS3/Xbox.I'm trying to get an OPEN NAT type but just can't seem to get it working.I've read a few different pages and have tried some things but it's never worked.I've heard of bridging connections and the sort but I'm not familiar with it. I just want to get an OPEN NAT on my PS3/Xbox.
View 10 Replies
View Related
Jan 18, 2012
My data usage via my ATT dsl link has gone over the limit for the past 2 months.
Perhaps a neighbor is using my connection?
I would like to set a password for my dLink connection.
View 16 Replies
View Related
Sep 19, 2011
I've a new Dlink DIR-632. All ports snif from outside are answering stealth by default. And the port forwarding feature works good.The problem is that I would like to allow a trusted net IP to reach my computer, whatever the request may be (whatever tcp/udp and on any ports). A kind of DMZ just for a precise IP. I tried the inbound filter feature. I've choosen allow, and I've put the remote IP start and end the same IP. It has been added correctly to the list. However, this IP still doesn't seem to be able to access to my computer on any port unless it tries on an already forwarded port.
View 1 Replies
View Related
Jan 1, 2012
This is my first post and I'm not very techy, but our home computer running Windows XP Professional recently lost its connection to the internet and I cannot get it back.This particular desktop computer is connected by a cable to the router. I have two other laptops connected wirelessly through the same router and have access to the internet, however the regular "J&A" network normally associated with the router cannot be connected to. Instead another wireless signal source called "DLink 4 (dlink)" is the connection point. This automacally disconnects when I unplug the router, so I'm assuming the router works fine, but the network is compromised somehow.
View 11 Replies
View Related
Jul 28, 2012
For reasons that are slowly pushing me over the edge of insanity, I have to reset this dumb router!!
I press the stupid little button on the back of it, the lights go out, one amber one comes on etc. etc. but when I go to 192.168.0.1, everything is still the same!!
Like the passwords are still there and nothing has changed! I thought resetting it was supposed to wipe all that stuff out so you could start from scratch? Also pulled the power cord in and out a zillion times but no way it will reset!
As an aside, I am having no end of problems getting my iPads (2) and iPhones (2) to connect to the wireless network! The "Network Discovery" button will not stay checked and though I have done all the Googling and been into Services to start things running, no way it is going to work!
But I digress, how do I get this fool of a router to reset properly?
View 1 Replies
View Related
Nov 5, 2011
I am trying to setup ATT DSL modem through D-Link router Dir-615. I was instructed to use PPPoE and setup username and password in router. When I do, the router does not save my network password, but reverts back to some hidden password. I have tried changing it in Tools, but it keeps reverting. I'm sure this is why I cannot access the internet.
View 1 Replies
View Related
Aug 30, 2012
I was assisting a friend by trying to set up a wireless password on their network, I have no clue why they didn't have one, and when it did the normal resetting machine protocol after the password setup we lost all internet, we can connect to the wireless network fine but it has no internet. The modem has internet connection as when I link via ethernet I can connect to the internet. DHCP is not enabled on the router, I'm not sure if I have to set that setting on the modem? or frankly how to do that either.
View 7 Replies
View Related
Aug 8, 2011
my dir615 is unsecured how do i make it secure
View 1 Replies
View Related
Aug 3, 2011
For some reason my wife's laptop has lost its connection to my router and when I put in what has always been my security key it gives me an error message saying that it has to be such and such for WEP ?I logged into the D-Link router but could not locate the place where the security key is set. Any way to that part of the firmware so I can reset the security key.
View 1 Replies
View Related
Apr 20, 2011
My dlink N150 keeps disconnecting
View 2 Replies
View Related
Feb 21, 2012
I have a dlink router. Dir615 I believe. After installing hotspot Shield on my desktop, I can no longer connect to my router from my laptop, which I did not even install Hotspot shield in. when trying to connect, nothing happens. the wireless icon on the taskbar does not show that its trying to connect.
View 2 Replies
View Related
May 4, 2012
Where do I find the security key for this DIR-827 dlink
View 2 Replies
View Related
Nov 15, 2012
I have a Ricoh printer hiding on a Dlink DIR-655 with a 192.168.10.101 address. This gateways to 192.168.1.1, which is a Westell DSL modem. I need to allow wireless accounts on the Westell modem to communicate with, and only with, the Ricoh printer.
View 3 Replies
View Related
Jan 2, 2012
How do i setup my d link dwl 2100 ap at my new address. I have moved and my installation cd has gone missing. The install wizard wants to work off the cd
View 2 Replies
View Related
Jun 1, 2011
can i use dlink switch as a router to set up LAN
View 1 Replies
View Related
