DLink DI-624 - Router Not Working Or Making Connections
Mar 28, 2012
I'm running XP and have Bell-Aliant modem SIEMENS Gigaset SE567 running to DI-624 router. It has been working for years but after the internet was down in the area for most of the day, it has failed to reset. I've done the usual un-plug/wait/replug routine a few times but cannot connect. I can connect directly through the SIEMENS but when I introduce the DI-624 back into the mix, I'm not able to connect to the internet. How do I make it happen. I'm not tech savvy so go slow.
I'm trying to connect our ASUS VIJ series laptop to a dlink DIR-615 wireless router. The router connection page asks us to: "Please enter the PIN from your wireless device and click the below "Connect" button". How to find the PIN number for the laptop? The laptop uses a wireless g connection. The laptop can find the dlink router's signal on the wireless profiles & has been connected wirelessly in the past to a router (a plug & play type) without a problem.
I have purchased a Dlink DWR 131 today. I did configure it as per the instructions. Initially my iPhone was able to detect the wireless network. Then I switched off the device and turned it on later and it stopped working. It is not damaged for sure, since http://192.168.0.1/ is still accessible from my laptop and I am able to connect to internet through LAN cable. But the wireless network is not working. Even my laptop doesn't detect the network neither does my iPhone. I suspect this to be some configuration issue. I have tried using different SSIDs. Also, MAC filter is disabled. I also tried using different wireless channels. I even did reset the router but no luck.
I have a Dlink dir-600 router I flashed it with dd-wrt it was was working good but I started experiencing some problems so I decided to flash it with the stock firmware and I did so later on after a week the Ethernet ports on the router stopped working I thought the router was bricked but I was able to connect wirelessly and could access the Internet and I was even able to change the settings of the router by going to 192.168.0.1 all was fine but all the ethernet ports stopped working so I thought it was the problem of the stock frimware and I again flashed it with dd-wrt but still all the Ethernet ports won't work I can only connect the computers wirelessly.
My dlink dir 628 wireless router suddenly stopped working yesterday. If I plug the ethernet cable directly into my computer and the internet works. I see the wireless profile in the options for the wireless internet, but when I try to connect, it is unable to do so.
I've tried resetting the router (using the button on the device) witand reinstalling the router (using the CD), but still not working. Also have tried turning off the modem, router, and restarting my computer.
I have 3 pc's connected to the router, hard wired in using cat5. When plugging the cable into the router, the router port on front lights up. If I put it in the 3 port, the 3 lights up. If I put it in the #1 port, the port 1 lights up. I believe it means the pc is being detected by the router. If I go to the ip addy for the router (192.168.0.1), it is only showing the pc I am on. The other 2 pc's are not appearing, and they are not able to access the network. If I add a wireless item, like my Iphone, it is detected on the network right away.This only started this morning. I have restarted the pc's, restarted the router, reset the router, moved the cables to different ports, and swapped the cables from one pc to another. The only pc that gets detected in all of this is the one I am on. Regardless of port/ wire.
Is there any way to make it so that my computer has two internet connections, so to my router it looks my computer is two separate computers, and would this increase my speed, since my router is made for up to 15 connections and has only 300mb/s to give out, so [would]each computer is[be] only limited to 20mb/s? As of now I have a dlink xtreme-n DWA-552 adapter in my computer.
The router stopped working for wired connections. I can still go online using my laptop via wifi, but when I connect a network cable to the laptop and turn off wi fi, connection does not work. Can't go online with a desktop with a wired connection to router.Everything else works via wi fi: iPad, android phone, tv with wifi.
My router was working just fine forever, the only computer that will connect VIA wire is my desktop, everything else for it to connect to my network it has to go wireless. Things like my blu ray player just will not connect. I am not an expert at all, but why is only the wireless working? I can use the Cisco connect and adjust the settings if need be.
I found my dir-601 router keeps making arp query to all ip addresses in same network periodically.all dhcp clients are general laptops and smart phone, I don't think there are any arp cheats attack on those devices.is it normal?
model: DIR-601 hardware version: B1 firmware version : 2.00NA
Ok, so what I want to do is make a router/firewall/proxy (maybe add webserver/FTP as well). Just to start off I want to say that I have moderate knowledge of Linux, enough to administer it from the CL. I have setup routers before but it was years ago and I've forgotten some of the details involved. What I do is a base LAMP install, with DNS, Samba, DHCP server, OpenSSH and then Webmin for easier administration. I've also installed EHCP (easy hosting control panel) in the past but have not at this point.
So, what I want to know is how do I setup the NIC's in the etc/network/interfaces file. Let's say that eth0 connects to the modem and eth1 & 2 are internal adapters. Currently my network is running a Linksys WRT54GL with DD-WRT and the router is set to DHCP for the WAN connection and DHCP is running on the internal network as well. The modem is at 192.168.254.254 and is giving the router an address of 192.168.254.1 my internal network is 192.168.1.1 (192.168.1.0/24). I would like to setup my internal router address to 192.168.1.1 so I guess I need to set it to static in my interfaces config and then set my eth0 to dhcp. Does this sound correct?
So if I do the above my only question is how do I setup the routing tables after that? I always get messed up when I need to make the switch from my Linksys router to my Linux box. I'm not worried about firewall rules at first I can change those once I have the router up and running. I just don't know if I need to make some kind of bridge to bridge the eth0 and eth1 (external NIC and internal NIC).
I bought my Sony Vaio notebook about 2 years ago and have since had problems connecting to certain networks. The laptop will connect to the network but when i open my web broswer it doesn't let me access any web pages. Basically there's no internet connection even though im getting a full strength wifi connection.
This problem only happens in certain locations. My parents house its fine (using a sky router), my old house in London fine (sky router again), my friends house (doesn't work), my new house (doesn't work - BT router), on the train (no again)
Its very frustrating, although it was manageable before as it worked in both my houses. However now it doesn't work in my new house its pretty much pointless me having the internet.
My computer is a Dell Inspiron with Windows 7 Home Premium Service Pack 1. A few weeks ago, it stopped working and would not let me log in. I fixed that problem by launching Setup and downloading the Windows 7 installation from a jump drive. The new problem is that I cannot connect to the internet at all. My wireless connections will not show up and when I hook up my ethernet cord, it will not show up either.
I have a DIR-655 with both wired and wireless connections. Yesterday, network stopped working on one wired machine while using it to surf the internet and a 2nd wired machine has not worked in 3 weeks after moving it from one room to another. Wireless connections are working fine.
-2 wired systems (Windows 7 and Windows XP), both stopped working -2 wired Xboxes - working fine -2 laptops, wireless working fine -1 smart phone, wireless working fine
I've power cycled my DSL modem and DIR-655 multiple times.Power cycled computer multiple times. Tried Win7 built-in diagnostics.Tried setting up static IPs.Tried filling in preferred DHCP server address.Disabled Windows firewall. [code]
I have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655 Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
I have a linksys system WRT54G at home. I had no problems with the Linksys router until about a month ago when I decided to make it a secure network. I run three computers of the wireless router (1 desktp and 2 laptops) Since making the wireless network secure I can not connect with my business laptop IBM Thinkpad X40, but thother e computers work just fine.
i bought a computer the old one works fine but it is slow. am using ethernet dsl cable. it connects through lan connections. the new one connects local only and will not let me get on internetwhen i try to go on the internet it brings up a connection through broadband and askes for a user name and password. the other computer doesn't and i have no username or password through the dsl.
i want to make my minecraft and gmod servers permanent so i got stupid and built a low powered server out of an old athlon media pc i had laying around. anyways my current setup i have going is my main router is in the basement and i have a dd-wrt d-link repeater in my room. ok so i gave the repeater a static ip of 192.168.1.56, and gave my server a static ip of 192.168.69.25 (i made the ip of the repeater 192.168.69.1) i forwarded all the necessary ports to the static ip of the repeater then to the static ip of the server. but my servers wont work. on minecraft it says "end of stream" but if i look at the active server log on the server it says "myipaddress has lost connection" and on gmod i just cant connect or see my server at all.
You have to make 4 subnets for 4 VLANs, the router interface assigned to each VLAN is the LAST usable host on the subnet.so unless I'm really bad at networking the graph should be:
Is this correct? I'm not sure whether the default gateway should be 192.168.0.255 (as would with normal subnets) or as I wrote down 192.168.0.126, this is the first time i've ever gotten assignments including VLANs and I havn't really gotten a solid explanation.
I have a computer hooked up to the internet with a cable modem via usb cable. The ethernet part of the modem is hooked up to my xbox 360.
I don't have a wireless router or a wireless internet connection but I do have a Belkin USB Wireless Adapter and I read on the web that you can turn your computer into a wireless hotspot if your computer has a wireless card with antennae or a usb wireless adapter.
Example, I have a Nintendo USB Wireless Adapter. All I do is stick it into my computer's USB port and it becomes a hotspot that I use to connect to my Nintendo DS to the internet wirelessly. So I basically thought that my Belkin adapter would be able to do the same thing only with whatever other devices I try, not my DS.
i have to make a wireless network for 48 apartments, thats in 4 floors and the area surface is 400 x 400 meters i want to go with netgear maybe buy 1 router and 2 access points?
I am wanting to make my desktop wireless I have a D LINK dual band wireless router now. My laptop is wireless and works fine my desk top is hardwired to router. Thinking of moving my moden and router to TV and making my desktop wireless and hardwireing my media server I think it called ( still yet to be bought still doing home work on which one to get and how to hook up ) Thinking less signal loss be hardwired to media server. I now have AT&T DSL 1.5 MB upgrading to 6.0 MB to stream netflicks . Do you think 6 MB will steam OK? Should I Go with just a USB adapter or go to PCI internal Adapter? In reading some of the other post seems hit or miss on adapter seeing and working with routher. Is there a brand or type of adapte I should look at? as I said Desktop will now be wireless media hardwire dose this sound like the way to go about doing this? Any media server that seems to work better than others . not doing x box or Wii not a gamer just want to stream Netflix without buffering and as good a picture as Poss.
I just a new motherboard yesterday an ASUS P7P55D. Running windows 7 and using ethernet, the internet would cut out after a few minutes and come back again by itself and cut off again. After turning on xbox live i realised that my computer is causing problems for the router and cutting off the connections.
I want to make the contents of my pc's hard drive available via my network (ie for use on the laptop), not just the media player library but the actual directories and files themselves. is this possible without a vpn? assuming so, how do I make it happen, and is there any way to secure this access further than just network access? Any easy-to-use and secure vpn.
I made a new connection with a password. And I have deleted the old connection on the "Manage wireless connections" But the old connection still appears on the Wireless connections. I don't want my neighbors to connect to the old one since it has no password, and I can't figure out how to delete it.
I installed a wireless adapter on my pc and since then when I play a game online or watch something online there will be times when the sound will be weird and noisy for a slight second along with the slowed visual. Also I noticed that it awakes the wireless printer from sleep mode. Could it the wireless adapter be interfering with the wireless printer? I tried to adjust wireless antenna but it didn't do anything.
