I installed a wireless adapter on my pc and since then when I play a game online or watch something online there will be times when the sound will be weird and noisy for a slight second along with the slowed visual. Also I noticed that it awakes the wireless printer from sleep mode. Could it the wireless adapter be interfering with the wireless printer? I tried to adjust wireless antenna but it didn't do anything.
View 2 RepliesAre there any manuals on how to open the srw224g4p switch? I can't find anything the switch is making a lot of noise - sound like the fan.
View 2 Replies View RelatedI have just replaced my 54Mbps Wireless-G router (Sky Broadband/Netgear - black, looks like a SkyHD box) with a 300Mbps Wireless-N TP-Link TD-W8960N router, I have also upgraded the the standard 3dBi antennas with a pair of TP-Link ANT2408CL 8dBi high-gain anetnnas.
However when using various WiFi analysis apps I'm getting a signal strength averaging -35dBm and noise of -96dBm when in the same room as the router. But the main bit confusing me is that this is in ALL configurations - with my old Wireless-G router, with the new Wireless-N w/ 3dBi antennas, and with the new Wireless-N w/ 8dBi antennas.
Am I misunderstanding the signal/noise thing or is this Wireless-N router not giving me a better signal at all? I plan on installing an identical setup in a property with patchy Wireless-G coverage next week and I was hoping this exact kit would be the solution.I have tested with two laptops and I am getting 130Mbps link with both, but I understand this is typical of laptop hardware. I don't have any devices with a certified 300Mbps card installed to test with.
I have a Cisco AP1142 Standalone AP at two of my locations. However both of these are being rendered useless every night and require a reeboot to correct the issue, because of the high level of noise and vibrations coming from the extremly loud bands that play there, Someone sugested an enclosure stuffed with insulation but Im afriad of overheating the AP.
View 2 Replies View RelatedI have a computer hooked up to the internet with a cable modem via usb cable. The ethernet part of the modem is hooked up to my xbox 360.
I don't have a wireless router or a wireless internet connection but I do have a Belkin USB Wireless Adapter and I read on the web that you can turn your computer into a wireless hotspot if your computer has a wireless card with antennae or a usb wireless adapter.
Example, I have a Nintendo USB Wireless Adapter. All I do is stick it into my computer's USB port and it becomes a hotspot that I use to connect to my Nintendo DS to the internet wirelessly. So I basically thought that my Belkin adapter would be able to do the same thing only with whatever other devices I try, not my DS.
i WANT Making Wireless access secure
View 1 Replies View Relatedi have to make a wireless network for 48 apartments, thats in 4 floors and the area surface is 400 x 400 meters i want to go with netgear maybe buy 1 router and 2 access points?
View 1 Replies View RelatedWhat size fans these are and/or had experience replacing them with something quieter?
View 15 Replies View RelatedI am wanting to make my desktop wireless I have a D LINK dual band wireless router now. My laptop is wireless and works fine my desk top is hardwired to router. Thinking of moving my moden and router to TV and making my desktop wireless and hardwireing my media server I think it called ( still yet to be bought still doing home work on which one to get and how to hook up ) Thinking less signal loss be hardwired to media server. I now have AT&T DSL 1.5 MB upgrading to 6.0 MB to stream netflicks . Do you think 6 MB will steam OK? Should I Go with just a USB adapter or go to PCI internal Adapter? In reading some of the other post seems hit or miss on adapter seeing and working with routher. Is there a brand or type of adapte I should look at? as I said Desktop will now be wireless media hardwire dose this sound like the way to go about doing this? Any media server that seems to work better than others . not doing x box or Wii not a gamer just want to stream Netflix without buffering and as good a picture as Poss.
View 1 Replies View RelatedI just purchased a Netgear router and installed it like it said on the directions. I have internet through Time Warner Cable. I did have a crappy phone before I got the router and it made a popping noise on it too, but I got a new phone and it was fine. But after I installed the router the phone makes a popping/clicking noise and it will also disconnect the wi-fi signal and I have to restart the router.
View 4 Replies View RelatedEvery 30 minutes we get a constant beeping noise from our router that lasts about a minute.
View 2 Replies View RelatedAt the moment i have 3 routers across the house, each acting as a wifi access point.My problem comes to when i use my phone or laptop, it connect to a random access point doesn't matter of the signal.Is it possible to combine 3 routers as one access point. So that i would connect to one access instead of 1of 3 access points, that would be a strong wifi signal no matter when i am in the house. Something similar to what bit malls or stores have.I have looked at wi-fi repeaters, but they just repeat the wifi and make new access point.
View 2 Replies View RelatedThe command that is given returns an error at the letter a in archive. The command I used was: archive download-sw /overwrite /reload tftp:// obviously with my tftp server info and file name at the end. I logged in with privileged EXEC mode as directed, but archive is not listed when I type ? to get a list of commands. I need to have this AP up and running by Monday.
View 3 Replies View RelatedI've bought a new Cisco 886VA and want to set the noise-margin value. With my old 876 I had to set "service internal" and then I was able to configure the value unter ATM inter config.
But with the new 886VA I can't find a way to configure it.
I have an Orange Livebox connected wirelessly to my laptop. Everything's been working fine until the last few weeks. Whenever I receive or make a call using my iDECT s2i cordless telephone the internet drops and it takes ages to reconnect. I've checked all the connections and every phone socket has an ADSL filter. I understand that some wireless devices can affect a router and that these are usually 2.4ghz devices but I have no idea if my cordless telephones are 2.4ghz or 5.8ghz or indeed if this is the source of the problem at all.
View 2 Replies View Relatedmaking a wireless connection from my broadband router model td 8816?
View 1 Replies View RelatedThe WAG120N makes a cracking noise on the conventional telephone.
View 1 Replies View RelatedIn official information for SG300-28p noise level is 40.6 dB, but in fact its too noisy. Is it possible to change speed of fans? I use only 8 PoE ports.
View 1 Replies View RelatedWe connected 4 wireless access points (AP541N-E-K9) to an SG300-10P switch.We want to be sure that no wireless clients can alter settings to the network by connecting to any of the networking devices. We also want that no wireless devices (except a few) can connect to computers that are on the wired network. I'm new to configuring networking devices so how to set up the switch for this.We already added all the MAC-adresses of all the wireless devices (that are allowed to use the wireless network) to the access points.
View 3 Replies View RelatedI have an application, a solar power plant, where communication cables (Cat.6 UTP) are run close to power cables. We've had a lot of failures in the past due to multiple reasons, electrical noise, surge, etc so we decided to change to Cat.6 SFTP. The problem is that now , even with proper termination of the shielding at either one or both ends, the noise is so bad that packet loss is above 90%.
View 8 Replies View RelatedComparing my brand new linksys x3000 (Firmware Version:v1.0.03) with my old zyxel p660hw I see that the linksys is running a downstream noise margin of 8.2dB while the old zyxel is running a downstream noise margin of 15dB. Needless to say, I am very disappointed. why the linksys value should be so much lower?
View 5 Replies View RelatedSo this problem seemed to come out of nowhere, I have no idea why it started. Basically, when I use my internet, eg: opening link, loading video or downloading randomly my speakers make a grinding noise and until the noise stops (can be 1-10 seconds) my internet drops (the internet icon on the bottom right shows it is still connected but nothing loads until the noise stops. Even then, the noise can drop in and out like 10 times in a minute and is constantly messing up the internet.
my speakers are Logitech (doubt that makes much difference as I doubt the problem is linked to them and my LAN card is some Ralink thing, nothing special. Here is a low volume recording of the noise, turn up your speakers to hear it well.
This has been driving me absolutely crazy but I am glad to have found the source of it. Over the past 4-5 weeks ever since i built my new computer, my computer has always had this wierd high pitch noise. I dont know if its coil whine or not, but the sound signature is def not the same as the coil whine that comes from my 7970 card. It sounds more digital.
What could be the cause of this? And what would the remedy be? My ethernet cable is approx 60 ft so it will be a pain in the ass to replace. Or buy another NIC?
edit: forgot to mention....the noise is constant. Not intermittent with usage. No amount of load or idle on the network changes the noise.
I have a linksys system WRT54G at home. I had no problems with the Linksys router until about a month ago when I decided to make it a secure network. I run three computers of the wireless router (1 desktp and 2 laptops) Since making the wireless network secure I can not connect with my business laptop IBM Thinkpad X40, but thother e computers work just fine.
View 8 Replies View Relatedi bought a computer the old one works fine but it is slow. am using ethernet dsl cable. it connects through lan connections. the new one connects local only and will not let me get on internetwhen i try to go on the internet it brings up a connection through broadband and askes for a user name and password. the other computer doesn't and i have no username or password through the dsl.
View 2 Replies View Relatedi want to make my minecraft and gmod servers permanent so i got stupid and built a low powered server out of an old athlon media pc i had laying around. anyways my current setup i have going is my main router is in the basement and i have a dd-wrt d-link repeater in my room. ok so i gave the repeater a static ip of 192.168.1.56, and gave my server a static ip of 192.168.69.25 (i made the ip of the repeater 192.168.69.1) i forwarded all the necessary ports to the static ip of the repeater then to the static ip of the server. but my servers wont work. on minecraft it says "end of stream" but if i look at the active server log on the server it says "myipaddress has lost connection" and on gmod i just cant connect or see my server at all.
View 4 Replies View RelatedMaking Configuration between 2 Apps?
View 1 Replies View RelatedYou have to make 4 subnets for 4 VLANs, the router interface assigned to each VLAN is the LAST usable host on the subnet.so unless I'm really bad at networking the graph should be:
NET ID // HOSTS // BROADCAST ADDRESS // VLAN
192.168.0.0 // 192.168.0.1 - 192.168.0.62 // 192.168.0.63 // VLAN1
192.168.0.64 // 192.168.0.65 - 192.168.0.126 // 192.168.0.127 // VLAN2
192.168.0.128 // 192.168.0.129 - 192.168.0.190 // 192.168.0.191 // VLAN3
192.168.0.192 // 192.168.0.193 - 192.168.0.254 // 192.168.0.255 // VLAN4
So if I'd have to write down a single host configuration for VLAN2..I think it should be:
IP: 192.168.0.65
subnet mask: 255.255.255.192
default gateway: 192.168.0.126
Is this correct? I'm not sure whether the default gateway should be 192.168.0.255 (as would with normal subnets) or as I wrote down 192.168.0.126, this is the first time i've ever gotten assignments including VLANs and I havn't really gotten a solid explanation.
I'm trying to connect our ASUS VIJ series laptop to a dlink DIR-615 wireless router. The router connection page asks us to: "Please enter the PIN from your wireless device and click the below "Connect" button". How to find the PIN number for the laptop? The laptop uses a wireless g connection. The laptop can find the dlink router's signal on the wireless profiles & has been connected wirelessly in the past to a router (a plug & play type) without a problem.
View 7 Replies View RelatedIf you have a router connected to several computers can a person create a shared drive using a remote USB drive?
View 7 Replies View RelatedHow do i make sure that my voip softphone is going through the vpn i have and the other party ( voip prvider is seeing the vpn ip insted of my real ip
View 2 Replies View RelatedI'm running XP and have Bell-Aliant modem SIEMENS Gigaset SE567 running to DI-624 router. It has been working for years but after the internet was down in the area for most of the day, it has failed to reset. I've done the usual un-plug/wait/replug routine a few times but cannot connect. I can connect directly through the SIEMENS but when I introduce the DI-624 back into the mix, I'm not able to connect to the internet. How do I make it happen. I'm not tech savvy so go slow.
View 1 Replies View RelatedI just a new motherboard yesterday an ASUS P7P55D. Running windows 7 and using ethernet, the internet would cut out after a few minutes and come back again by itself and cut off again. After turning on xbox live i realised that my computer is causing problems for the router and cutting off the connections.
View 1 Replies View Related