Linksys WRT45G / Connection Going Off And On?
Jan 14, 2013
Recently I've been having this issue were my internet connection stops working and usually repairing the connection through control panel or unplugging the router and plugging back only temporarily reconnects me as in the next 5-10 minutes my internet is offline again. This is very annoying especially for online games as I have to constantly relog into the games. My router is a Linksys WRT45G and I use Windows XP Also on some days my internet actually works for a decent amount of time. Mainly seems to happen after I decide to play one of my online games although it has stopped working a few times even when I am not playing those games?
View 1 Replies
ADVERTISEMENT
Sep 15, 2011
I was requested to connect 2 WRT54G devices in our network with same ip range.
View 2 Replies
View Related
Jul 13, 2008
I need to remotely monitor a WRT45G from a remote host on the Internet. As such, I want to allow ICMP ping replies on the public Internet interface. However, I have found no feature to allow me to do this. Similar Netgear devices do allow this feature. I suspect the answer is, "you can't do that".
View 2 Replies
View Related
Sep 22, 2011
i have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
info:
led power is on stable
led lan is on
led wlan on and the access point work
1.http:\192.168.1.1
2.enter user name and password (admin,admin)
3.hir the page begin to get after a few second the router reboot Page cannot be displayed completelty
i try :
- simple reset
-(30/30/30) reset and i enter in managment mode firmware upgrade
i don't try hardware reset
View 6 Replies
View Related
Sep 22, 2011
i have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
View 4 Replies
View Related
Aug 18, 2011
Here's the issue, I will have the router up and running with two laptops and an Iphone connected through wireless.
The connection will show still connected but I will have no internet connection. I haven't tried this wired yet. The only way I can resolve it is reseting the router on the back, restoring it to factory default. Which resets password, mac filter and all that jazz.
View 1 Replies
View Related
Dec 11, 2011
How do you set up a linksys routers internet configuration type to public/bridge mode? my model is WRT45g
View 1 Replies
View Related
Jan 28, 2013
I don' know how to setup the LinkSys WRT45G (v2) router properly for the way I want to have things wired. I have Verizon FIOS in basement with MoCA enabled coax line going into a splitter, running lines throughout the house. The main router (Actiontec MI424WR) is on the first floor, east side of house connected by coax and the area I want to put the second access point (LinkSys) is on the second floor, west side of house. So very weak wireless signal where the LinkSys is at. I used a Actiontec Verizon Coaxial Network Adapter to plug into the coax outlet in the 2nd floor room. Then run an ethernet cable from that unit to a older LinkSys router WRT45g (v2). I wanted this router to provide a wireless access point and also a place to plug a Sonos unit into. On the back of the router is the usual RJ-45 port and the 4-port switch. I have the line coming from the moca adapter (source) going into port 1 of the switch, the Sonos 5 plugged into port 2 of the switch. I am able to connect and control the Sonos units about 50% of the time like this, but sometimes nothing can be found. I believe this is because my phone can not connect to the wireless when I am upstairs, anotherwards the LinkSys router is not working right. If I plug the ethernet cable from the MoCA adapter into the RJ-45 interent port (like I think it should be, since it is the source), then nothing works.Also, I do not know if the router is functioning as a wireless access point, I am suspecting it is not.The router still has stock firmware, has DHCP disabled, the security and SSID identical to the primary router.
View 1 Replies
View Related
Jul 16, 2012
A couple days ago, our Linksys E2500 router accidentally got unplugged. Since then, the internet has been working extremely poorly (a lot of latency issues plus random disconnects), so yesterday we tried soft resetting the router. This backfired immensely as now the network no longer exists and we can't access either the router or the internet through the router.If we have an ethernet cable go from the modem directly into a computer, the internet works fine (which is how I'm posting). But if we hook the modem up to the router and then another cable from the router into a computer, we get nothing. We can't even see the router.We've tried unplugging the modem and router and then plugging them back in, unplugging just the modem, and unplugging just the router to try to get it back working but that didn't work. We then tried holding down the reset button on the bottom of the router for fifteen seconds then unplugging the modem and router, holding down the reset button with the modem already disconnected then unplugging the router and plugging the modem back in then the router, and holding down the reset button with the modem already disconnected then plugging the router back in then the modem. And then we tried each of these things while waiting a minute before plugging everything back in. Nothing's worked. And everything we've googled to find out how to hard reset the router either says to do something I've already listed or requires using the router's configuration page, which we can't access (supposed to be 192.168.1.1, but nothing comes up when I enter that into my browser since we can't connect to the router).
View 14 Replies
View Related
Dec 26, 2012
My old WRT54G V8 router has been acting up lately. It keep dropping the connection out of the blue. Sometimes I'd be browsing the Internet when the router's signal vanishes completely, it disappears from the list of available wireless networks on not just my computer, but my smartphone and all other devices in the household! Other times I keep connected to the network but there's no access to the Internet. Everything seems fine on the ISP's part, I can connect just fine directly from my modem, so I'm certain the problem is with the router. Besides, these problems are solved by just power cycling the router.
Who is your Internet Service Provider (ISP)?
Amnet Costa Rica
What type of Broadband connection are you using?
Cable
What is the exact Make and Model of your Modem, Router or Modem/Router Combo Linksys WRT54G V8 What is the Name of the Anti-Virus, Security or Firewall Software Windows Security Essentials and Windows Firewall on all computers.Below is my ipconfig and Wi-Fi diagnostics from Xirrus Inspector attached.
Code:
Windows IP Configuration
Host Name . . . . . . . . . . . . : VAIO
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 7 Replies
View Related
Jul 7, 2011
I've been connecting my WRT54G2 router to our modem, and then using another ethernet cable to connect to my PC. That way I can have a wireless connection in my room and also be connected on my desktop. However, recently, I reset my router because I was having connection issues with a certain program, and I ran the setup CD afterwards just like I have every single time I've done this, but now I can't connect. I can access the router settings and everything just fine.It says I have a connection, and when I connect my desktop directly to my modem, I can connect just fine. When I have the router connected to the modem and try and connect wirelessly with another device, the access point pops up, and it begins to connect, but then fails in the end.
View 9 Replies
View Related
Jul 17, 2002
Network was:
AT&T Broadband ISP
LanCity LC-PET3 cable modem (non DOCSIS)
Linsys 4 port hub
2 Win98SE PCs
All worked fine
New network is: Same as above, with a Linksys 1 port router (BFSR11) between the cable modem and the hub.
Router is configured to be a DHCP server (default configuration).
I assigned the router a custom WAN side MAC to match one of my two PCs to avoid having to call AT&T to get things running.
Results: Everything runs perfectly fine initially, but after leaving and coming back to either system (left on, in standby) after quite a while (going to work / bed), the network connection is dead.
WINIPCFG still reports the same IP, but seems to hang forever if I attempt to release / renew. The router's is unreachable for configuration / status (it's still on the default IP of 192.168.1.1) Pressing the reset button on the back of the router restores the internet connection (quickly too - I'm back online in about 15 seconds).
Entering standby manually and coming back out again after just a couple minutes does not affect the internet connection - it seems to only occur when I'm off for an extended period of time. I have no had the time to determine what the period of time is, and if it is a fixed time since DHCP lease / initial startup, or if it is a fixed amount of inactivity time (or maybe even not a fixed amount of time at all).
View 7 Replies
View Related
Feb 2, 2012
I need to figure out how to connect my home router to my AT&T MiFi. I have 3 DVD players and one computer hard wired to the router. The MiFi works great with my laptop and IPad that has wireless capability but how can I get it to connect to non-wireless devices connect to my router?
View 1 Replies
View Related
Sep 12, 2011
linksys router problems Linksys wireless router connected to cable modem. over time router looses connection to internet. rebooting router reestablishes connection. running XP sp3 from laptop connected wirelessly?
View 3 Replies
View Related
Jan 12, 2012
My internet connection drops intermittent along with everything else that is setup with the router. The router is linksys wrt110 and the cable modem is linksys befcmu10. Both of them probably needs updating but, can't seem to update and I can't access the web based server at 192.168.1.1
View 3 Replies
View Related
Jan 7, 2011
I have been using a linksys 5 port workgroup switch in my room. I have the ethernet cable coming from the router into the uplink port and my PS3, xbox, dvr, and pc in the other ports. It has been working fine until today I started messing around the the cables. I had trouble with the ps3 connecting to the internet so I used my laptop with wifi disabled to test out a few of the cables and ports. Now all of a sudden the switch kills the internet connection. If I remove the cable running to my room from the main router, the other PCs and wireless will connect, but as soon I plug myself up it goes dead. I now have the ethernet cable in my room hooked directly to the PC bypassing the switch and everything works fine now.
View 3 Replies
View Related
Jul 7, 2012
The case is I have a Linksys WRT 54 G2 V1.5 router for my wireless connection but the signal does not get to the other side of the apartment. I Got a RE1000 wireless extender, someone said this is what i needed, and it worked fine for a few hours, but then it keeps dropping my internet connection everywhere in the apartment.
View 19 Replies
View Related
Sep 22, 2012
There are 2 ps3,a wii ,2 laptops,3 desktops,2 dsi.We have been having issues for a while now with losing connection and the service provider says there is nothing wrong. the modem is a comtrend ct-5072t and the router is a linksys E3000. The E3000 is the 3rd router I have bought in the last yr and 1/2 the last was a d-link dgl4500 gaming router the modem is new a rentel from the provider. Downloading updates for the ps3s are a nightmare online games like arma2 and battlefield 3 are a pain because we are losing connection all the time dont know what to do.
View 4 Replies
View Related
Jan 27, 2011
my linksys e3000 router loses connection quite often. E.G. we lost power last night and i tried resetting the router but it didnt work so I had to uninstall and then reinstall the router. A few other times it would lose connection for no apparent reason.
View 8 Replies
View Related
Nov 25, 2011
My LInksys router keeps losing internet connection. I have to unplug it and then plug it back in....
View 1 Replies
View Related
May 3, 2011
I am using a PPPoE connection on a linksys WRT54G router and trying to set up an Edimax EW-7206APg to extend my wireless connection range.I followed the instructions given on the Edimax manual, but that seems to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connectionMy router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest. What am I doing wrong?
View 2 Replies
View Related
Jun 27, 2011
I am not that good at troubleshooting network issue but luckily I was able to figure out a problem I had with internet connection not working through my Linksys router. My computer is connected hardwire through a wireless router (linksys) and I have 3 wireless devices that connect to the wireless router.I have had the wireless router for about a year and half. I set it up myself and have had no problems since day one until today.It was working fine this morning, my computer was on the whole time, I never shut it down and all of a sudden a couple hours later went back to my computer and couldn't access the internet. "No internet access" message on the taskbar right hand side.Not one of my wireless devices connect to the internet including my desktop that is hardwired.
I tried resetting the modem...no luck. I'm thinking outage or something else that had to do with my cable company. I called them, the lady had me try without the router, worked fine, problem with router.I called linksys since I am not good at troubleshooting router issues and did not want to reconfigure everything and start from scratch.The lady at linksys says the router is out of warranty and after a year they cannot provide free tech support and wanted to charge me for either two of their paid tech support which the cheapest was 30 bucks. After some time of trying to figure out the problem I notice my ip address was different.
View 5 Replies
View Related
Feb 1, 2012
I installed my new X2000 a couple of days ago and my ADSL connection drops several times a day. Sometimes it will stay connected for a few minutes and other times it will stay connected for several hours. The only way to get it connected again is to reboot.I have used 2 other routers (D-Link DIR-300 and BT Home Hub 3.0) on the same line and haven't had any disconnection issues with them, so the problem must be a hardware/software fault on this router or I have set it up incorrectly.Judging by a number of posts I found online, there seems to be a general problem with DSL connections dropping on the X2000, especially on earlier firmware versions. I have subsequently upgraded to the latest firmware (Ver.2.0.01 (Build 4)), reset and reconfigured twice, but nothing has worked so far.Unless I can get this working in the next few days I am going to have to return it, which is a shame because the performance of the router is great when it's working!Would someone be able check I have configured the DSL settings on the router correctly?
DSL SettingsEncapsulation: RFC 2364 PPPoAMultiplexing : VCAutodetect: DisableVPI: 0VCI: 38Modulation: MultimodeMTU: 1400
View 6 Replies
View Related
Mar 22, 2011
when choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
View 4 Replies
View Related
Nov 28, 2011
I have a WRT54G2 v1 (no new firmware available) with a cable-modem connection (Motorola Surfboard), every thing works perfect but when my ISP goes down and then back up I cannot get the router work, LAN or Wifi connection. I have ping response to the router and I'm also able to get into the admin page. The only way to recover is restarting the router and sometimes releasing DHCP and then Renewing it, and the Wan connection actually gets the same IP it had before.
View 3 Replies
View Related
May 1, 2013
I purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
View 4 Replies
View Related
Nov 22, 2011
My dad recently got a E4200 router, My whole family are mac users, the connection are all okay with their computers, I'm the only one using Microsoft, ASUS running on Vista. The connection is fine when I'm near the router, but when I go to my room I get no connection at all, it connects for a second but then it goes on connection with limited access.
View 5 Replies
View Related
Nov 30, 2011
I'm having trouble with my Linksys X2000 modem/router to stay connected to internet. I have tried upgrading the firmware & changing my ip address, but still with no success.The router part is staying connected, but the dsl will drop off. I have to unplug to get it up and working again.
View 9 Replies
View Related
Mar 26, 2011
I have been using a WAG320N since January. Around a week ago I came home to find the unit attempting to reconnect every few minutes - the DSL light flashing but nothing happening.
I replaced with an old Belkin unit which worked fine straight away.
i have upgraded the firmware, which made no difference, and secondly, tried a brand new unit, which strangly had the same problem even though the ancient belkin unit works first time and my original cisco unit worked for a couple of months before failing.
Are there any settings that relate to the DSL connection that may have been reset on the original unit? Could this be an issue related to signal quality or anything similar?
View 5 Replies
View Related
Mar 21, 2012
Last week I bought the E4200 thinking it was probably the best router on the market and if it worked properly, it would be...I think.I have attached a Seagate GoFlex Desk 2Tb USB drive formatted to NTFS to the USB of the E4200. I can map to it from my Windows XP computer with no problem and I can FTP to it from any browser...my Windows 7 machine is another story. When I try to map the network drive from the Windows 7 machine I get error code 0x80070035 every time. I've seen some other threads where people are having this problem but in the cases I've found, they aren't getting any connection via XP or FTP either.
View 2 Replies
View Related
Aug 28, 2012
I have bought Linksys E3200 less than month ago.I have setup it, connected HD (WD My Book 1TB) through USB and it work good, without any problem.Than week ago, I turned off the router, because of my vacation. Yesterday, I came back, turned on the router. WiFi was working good, cable connection too. But there was no connection to HD. I had checked information about HD on admin page, router understood that it is HD, but not provided share access to folder, also, there was no button, to setup it.I disconnected HD, tried to connect it using the Cisco Connect, it provided mistake with USB connection to HD and than with HTTP connection to router. I disconnected HD, tried to connect it manually: connect HD -> go to admin page -> refresh to show HD -> admin page freeze... -> reboot of router manually.
There was a lot of tries to connect HD, but all was failed.I connect HD to computer, it works successfully.I checked connection to router through USB, using my card reader and SD flash card, it works successfully.Information about HW:
1. Linksys E3200, last update of firmware for German (was bought using German Amazon) country. (Cannot check it now, if needed will check)
2. Computer: Windows XP SP3
3. WD My Book 1TB (NTFS)
View 4 Replies
View Related
Nov 11, 2011
the other day i set up a new internet connection and to set it up they sent me a WAG160Nv2 modem router and after hours of trying to get it working the technical support guy told me it cant be set up until the dsl led comes on, so what it being off means/how to get it to turn on?
View 2 Replies
View Related
Sep 5, 2012
I have a Linksys WUSB100 ver.2 which i'm using on my desktop (uptodate Windows 7) for over a year now. I never had any problems with it until about a week ago.
After starting the computer, it had no network-connection, nor could it find any network anymore . The led-light keeps flashing blue and the device gets pretty hot.
I've tried about everything, i think:
- I've tried to update the drivers, but the installed driver were already uptodate.
- I have re-installed the device with no effect.
- i've installed the device on 2 other computers; my Windows 7- laptop and my old Windows XP SP3-computer. The problems were the same there.
View 2 Replies
View Related
