Here's the issue, I will have the router up and running with two laptops and an Iphone connected through wireless.
The connection will show still connected but I will have no internet connection. I haven't tried this wired yet. The only way I can resolve it is reseting the router on the back, restoring it to factory default. Which resets password, mac filter and all that jazz.
I was requested to connect 2 WRT54G devices in our network with same ip range.
View 2 Replies View RelatedI need to remotely monitor a WRT45G from a remote host on the Internet. As such, I want to allow ICMP ping replies on the public Internet interface. However, I have found no feature to allow me to do this. Similar Netgear devices do allow this feature. I suspect the answer is, "you can't do that".
View 2 Replies View Relatedi have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
info:
led power is on stable
led lan is on
led wlan on and the access point work
1.http:\192.168.1.1
2.enter user name and password (admin,admin)
3.hir the page begin to get after a few second the router reboot Page cannot be displayed completelty
i try :
- simple reset
-(30/30/30) reset and i enter in managment mode firmware upgrade
i don't try hardware reset
i have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
View 4 Replies View RelatedI'm having an intermittent issue with my E4200v2 router. Frequently I will be using a device on the wireless network, and it will be unable to reach the internet. Normally I would assume this was a problem with the cable modem, but disconnecting from and reconnecting to the router often fixes the problem.
View 9 Replies View RelatedI have spent several hours with Linksys support (six calls) and my ISP (2 calls) and still can't get my router working. It will work for about 5 minutes or and then drop Internet access. If I unplug and reboot, etc, it will work for another 5 minutes or so and then drop signal again.
View 9 Replies View Relatede4200 internet keeps dropping
View 9 Replies View RelatedI have a WRT54G wireless router and it goes through periods where it constantly has to be reset cause it keeps dropping the internet connection. Once you do a power cycle it starts working right again. But sometimes goes out 5mins later.I have the router hooked up to a Windows XP computer via an ethernet cable...and I have 1 Windows Vista laptop, 2 Android phones and a PS3 connected via wireless.The PS3 is set up following these directions: (not sure if this is what's screwing it up)
"Step 1:Open a web browsersuch as Internet Explorer.
Step 2:Go to the Address bar and enter your router's IP address ("192.168.1.1" is the default IP of most Linksys routers) then press [Enter].
Step 3:When the router's web-based setup page appears, click Applications& Gaming then click DMZ.
Step 4:Select Enable on DMZ and under DMZ Host IP Address enter the PlayStation®3's IP address.
- Try 192.168.1.10 or 192.168.1.20 Save Settings.
- This IP address will need to typed in manually during online setup on ps3. I think its the first address you enter (I think this is the game's IP address).
- Use 192.168.1.1 for the wireless router's IP address on your PS3.
Step 5:Now, click Administration and Disable UPnP. Make sure you also disable UPnP on your ps3 online setup. Save Settings.
Step 6:Click Status. Write down the DNS 1: dns number and DNS 2: dns number on a piece of paper. You will enter these for DNS 1 and DNS 2 numbers during online ps3 setup. NOTE: The IP address listed on the Status page for your wireless router is not used for any setup on your ps3. Remember, to get into ps3 online setup, you have to choose Manual during setup so you can enter these numbers.
Step 7:The WP key crap and whatever during online setup should be skipped unless you specifically setup some kind of password for your wireless router when you installed it. I didn't and just left that part blank and skipped over it.That should get your wireless router and game setup. If you're still stuck, drop me a message.And, remember to do this setup after that:Linksys has a great tech support at their site. url...
I have a ps3 and did all of the wireless and ps3 online setup for it using their site technical support. Doing that seemed to throw a monkey wrench into my internet connection a while after that. I just left all of my game settings in place and did this: Logon on to your wireless router. To do this, you will probably go to url.. by typing this address into your address box on your internet explorer. Logon. If you don't know how to logon, go to and follow the instructions in technical support.
My wrt400n was working great but since last few days internet keeps dropping. My modem is all good and up and running. Its just router keeps dropping internet. SO i have reset the router and than it works.
View 6 Replies View RelatedCurrently running Windows 7, with internet explorer. I have most recent firmware installed on my e2500. The unit drops wireless connectivity on an intermittent basis. Sometimes after 5 minutes and sometimes after 20 or 30 minutes.
View 9 Replies View RelatedI had the 2 Wire Box that received TV and internet. Called my ISP and they gave me this access point to use instead. I hooked it up and it was fine for about 2 weeks. Suddenly for no reason it started dropping. Noticed it first when online gaming on my PS3. Checked laptop and all wireless devices down. Takes about 30 seconds.
View 1 Replies View RelatedWired connection to the router works fine. But it drops all the wireless devices (PC, phone, tablet) multiple times each day, sometimes only 30-60 minutes after reconnecting. Power cycling the router "fixes" the router and allows reconnection. There are 2 topics in the FAQ section that looked good: Getting poor or no signal from a wireless routerTop causes of dropping wireless connection on a Linksys routerbut clicking on those does not bring up anything.
View 9 Replies View RelatedSet up: Router: WRT110 1 computer connected via ethernet cable 1 computer using a wireless nic card from cisco
The problem is thus: if the first computer is actively using the internet (even activities as mundane as browsing one's email) the computer connected wirelessly will lose its connection to the internet yet maintain its connection to the router. Both can be actively using the internet, but the wireless will seemingly at random drop internet access (usually in 30-120 minute intervals).
The computer connected via the ethernet cable was unplugged for a week and during that time the wirelessly connected computer was used extensively and did not lose connection once.
I don't understand how to even frame this problem in a concise manner, much less seek information as to how to resolve it. It's seemingly giving all priority to the computer connected via ethernet but I that's just intution speaking.
I recently changed the security mode on my router from WEP to WPA2 Personal. However, since that change, I've noticed that the wireless devices, 2-laptops, are intermittently loosing their connections. . I don't know if it has anything to do with the security mode change, but I don't want to go back to WEP for obvious reasons.
View 9 Replies View RelatedI have a WRT54G conected to a desktop through a wire, and conected to a laptop wirelessly. It starts working fine, and after a while i get no internet connection in my laptop nor my desktop. After this happens i disconect the power source from the router, i conect it back again and it starts working.
View 9 Replies View RelatedI've been using my Linksys WRT54GC for couple years now, and only recently have I started to have significant issues with the device. I'm using a 2012 Macbook Pro, and my internet connection seems to be randomly dropping every now and then. Sometimes it works just fine for couple of hours only dropping once or so, sometimes it starts dropping literally every few seconds. What I usually do is quickly restart my wifi and the connection comes back right away. I also tried not doing that, and the internet connection tends to come back up after a minute or so.
I have read countless topics, also tried many things: changing MTU, the thresholds in router settings, security modes (it seemed to have worked fine after I changed it to WPA, not anymore though. I'm using no password now and it doesn't fix the problem either), changing the channel (my strongest signals around are on channel 1 and 11, thus I left mine on 6), I even reset the router today (held the reset button for 10 seconds~) but it didn't work either. I didn't upgrade the software since I heard stories about the software available on this site being corrupted or something, bricking the router, which is the last thing I'd want (I'm running on 1.00.7 now).
I have the impression (but it's just an impression, it might as well not be the case, and just me trying to find out when it happens, since it's not always that it breaks the connection while doing that) that it breaks the connection on high load, I mean when I'm for example using skype and facebook, and then try to go on reddit at the same time - the reddit webpage won't load, and the connection is lost after few seconds. But it also started dropping every few seconds while I was playing an online game and skyping at the same time today, which isn't a particularly huge problem for a 23Mbps download and 1.5 upload speed internet I suppose, and which it never did before. I have never had such issues with my PC using a Linksys USB adapter. The connection would drop from time to time when, for example, accidentally going on pages with lots of thumbnail pictures, or trying to load 15 tabs of jpgs at the same time, it was never that much of a problem really though, I just thought it's normal.
Set up:Router: WRT11.1 computer connected via ethernet cable.1 computer using a wireless nic card from cisco.The problem is thus: if the first computer is actively using the internet (even activities as mundane as browsing one's email) the computer connected wirelessly will lose its connection to the internet yet maintain its connection to the router. Both can be actively using the internet, but the wireless will seemingly at random drop internet access (usually in 30-120 minute intervals).The computer connected via the ethernet cable was unplugged for a week and during that time the wirelessly connected computer was used extensively and did not lose connection once.
View 2 Replies View Relatedever since i had a power failure losing all power in my apartment, my router has begun regularily losing connection to the internet, I have to go into the router and renew ip address which is quite annoying
[code]....
my e4200 wireless. I have internet connection speed of 40mb and I have epc 3925 working in bridged mode as modem and E4200 as router. When I connect my laptop with wire on e4200 I am getting 37-38 Mbps on speedtest.net which is perfectly fine. But on wireless I am having a lot of dropping of speed: I have 2mps then jumping to 5-6 Mbps and so on it never goes more than 5-6 Mbps. When I disable WMM Support in QoS I am having perfectly constant 20mbps but... I have only g network 54mbps. [code]
View 9 Replies View Related I've recently purchased the EA3500 dual band wireless-N router to replace my old and somewhat tired WRT54GS. The old router worked, I just decided to upgrade to wireless-N since all of my devices are now capable.My ISP is Comcast and I use a Motorola SB 6120 cable modem. After an extremely easy setup of the new router last week, I experienced one full day of glorious speedier network and internet traffic. However, roughly 24 hours after installation I started experiencing intermittetent internet connectivity issues. As in - the cable modem is accessible for 2 minutes and then can't be found for 2 minutes, repeat forever.
After multiple different troubleshooting steps, including rebooting both the modem and the router together, separately, and releasing and renewing the router's IP Address through the router's admin page, I finally ended up resetting the router back to factory defaults and letting Windows 7 guide me through the re-installation rather than using the provided "easy setup" CD from Cisco.
This seemed to have worked, but 2 days later, my "every 2 minutes" issue returned.
Something important to note here is that all of my devices - both wired and wireless - are able to communicate with each other without issue. For example - while I have no access to the cable modem, I am able to stream music from a wired desktop through a wireless laptop to a wireless receiver connected to my TV. I am also able to access the router's admin tools during my connectivity issues.
My wireless router will work for 6- 8hrs then drop the internet connection. I have to cycle the modem and router several times to restore the connection. I am also using a Netgear Access Point.
I am using:
Charter High Speed Internet
Motorola Modem
Cisco Model WRT120N Router
SETTINGS
Mode- Mixed
Channel Width- Auto 20MHz or 40MHz
Security- WPA2 Personal
SSID Broadcast- Disabled
Firmware Version v1.0.04
Connection Type- Auto Conf DHCP
Beacon Interval - 50
Fragmentation Threshold 2304
RTS Threshold 2304
All other setting are at factory default.When I unplug the modem from the router and plug it into the desk top I have internet service.
i am a total n00b when it comes to wireless routers etc,.. i bought this router [E3200] about six mths ago, it has been working just fine untill a couple days ago, wher i woud be on the internet and all of a sudden, the internet connection drops, i am using a cable modem [ARRIS TM722G] ,i did a reset on the e3200 and put restore the settings that did last over night
View 9 Replies View RelatedI have a home network with a Linksys E4200 connected to the ISP's fiber box. The problem is that when I'm connected to the Linksys, either wired or wireless, the connection to the internet will drop after what seems to be a random amount of time (normally anywhere from 2-10 minutes). I can restore the connection by doing any of these things:-reboot Linksys-disconnect and reconnect cable from router to fiber box-if on wireless connection, make changes to the router wifi settings, like change the wifi channel.The internal network stays up, and I can ping both the internal and external ip of the router, but not the fiber box. I have also had the same behavior with an Edimax Wifi AP and less frequently with a Edimax router (once every 1-2 days). I have done everything I can think of:-changed the wifi channels-changed the ip ranges, subnets, turned router DHCP off and back on-booted the fiber box-changed cables-updated all routers to the latest firmware, the network cards with latest drivers...and loads other things that I don't remember right now. For the wifi side of things, there are no other networks in range that could interfere. The same problem occurs on both my and wife's Win 7 laptops and on the iMac (latest OSX). Here's a fun detail: while the Linksys has lost its connection to the internet, I can still access the internet through the old Edimax router connected to the same fiber box, either wired or wireless.
View 1 Replies View RelatedI've recently picked up a E4200 to build a dual band network which is targeting to link up (TV, media server, ps3, laptops) then (maintaining phones etc which only has b/g). While currently only laptops.Before doing any of these I have another cisco modem router DPC3825 which worked fine with giving wireless access.I first attemped to leave the modem router has is and connected the E4200 (ethernet 1 to internet), and changed ip to x.x.0.1 and x.x.0.2 while disabling wireless on the dpc3825 and the DCHP on the e4200 and have default gateway to x.x.0.1. My laptops can connect to wireless on E4200 but it couldn't get internet access.
Then I tried turning the modem to bridge mode & resetted E4200 (factory setting x.x.1.1, auto DHCP), and then connected my devices to both wireless bands. At this point I see router status obtained ip from ISP and Internet reached full speed per ISP's mark but the connection only held up for about 1 minutes. I noticed all the devices still maintained connection to router wirelessly but the router loses internet connection (lost the ip and couldn't get it back).
How do you set up a linksys routers internet configuration type to public/bridge mode? my model is WRT45g
View 1 Replies View RelatedRecently I've been having this issue were my internet connection stops working and usually repairing the connection through control panel or unplugging the router and plugging back only temporarily reconnects me as in the next 5-10 minutes my internet is offline again. This is very annoying especially for online games as I have to constantly relog into the games. My router is a Linksys WRT45G and I use Windows XP Also on some days my internet actually works for a decent amount of time. Mainly seems to happen after I decide to play one of my online games although it has stopped working a few times even when I am not playing those games?
View 1 Replies View RelatedI am having problems after installing the ae2500 adapter in my win 7 machine had to remove malwarebytes and avg to get it to work but now it constantly has problems dropping the internet connection. I have to disable the adapter then enable it to reconnect to the internet. Are there other compatibility problems with this setup that I need to address?
View 1 Replies View RelatedI have two notebooks, one smartphone, and one blu-ray player that connects to my wireless network. My gaming PC is hard wired into the same router that broadcasts my wireless network. About 5-6 times, my wireless network will drop and everyone connected to it wirelessly will lose their connection for about 1-2 minutes. While my gaming PCs internet connection is undisturbed, all of my wireless devices can no longer "see" the network SSID and therefore connect to it. The problem has been happening consistently for many months.
View 1 Replies View RelatedI seem to all of a sudden be having some strange issues with my E4200. I am running Firmware Version: 1.0.05 . I am also using a Dlink DAP-1522 gigabit bridge. The main machines I am noticing the dropouts on are my main windows computer (connected to network via ethernet cable plugged into DAP-1522 bridge) and my wifes ipad. What happens is it drops connectin for about 3 minutes then comes right back. I am really perplexed as to what could be causing this. At first I would have thought it was a bridge issue but thats up to date and my wifes ipad dropping (which is connected via wifi) shows there is something else going on here.
View 9 Replies View RelatedMy router is dropping the downloadspeed from 20mb to 1. After turning off and on, the router restores for a few days.
View 3 Replies View RelatedI have a Linksys E900 router that seems to drop connections all the time. When I look at the status page, all the IP4 information is gone.
View 1 Replies View RelatedIt seems since I have moved into my new house months ago my E3000 keeps on dropping its signal. I have an older roouter that doesn't do this. Currently I have a PS3/Xbox 360 plugged in and then the 3 laptops that use the wireless.
View 1 Replies View Related