i recently enabled bridged mode on my first router/modem and now it seems that i cannot access the configuration with the normal 192.168.0.1 address. Is there anyway i can access the configuration excluding the hard reset?
View 1 RepliesI am attempting to replace my actiontec router with the Cisco 871 I have little expirience with CLI-IOS so I was trying to use sdm express that failed to load and when I finally got it to load it still didnt work and I ended up getting locked out of the router it was totally unresponsive. So I did a reset and now am attempting to use the Cisco Configuration Assistant to set up my wan connection but it have been loading security related data for 15 minutes and I have a feeling it's not doing anything at all. I don't understand what I'm doing wrong.... Any advice.... I just was trying to get a default set up that would give me internet access Im not trying to enable any of the security functionality at this point.
View 0 Replies View RelatedMy WRT54G Linksys router works with wifi and local connection but it wont let me configure to change it to PPpoe nor wont let me enable a wireless connection, so it's open to the public how do i get it to open it resetting it and holding the button on the router for 30 secs.
View 1 Replies View RelatedI set my router to allow my xbox360's mac address, not knowing that it would kick out all of my other devices. So now I can't access my own router and I need to reset it. How do I do that?E1200 series linksys router. I'm looking for an ethernet cable and my installation disk right now to see if I can connect with the cable and maybe use something on the disk if I have to.
View 1 Replies View RelatedI ran the firmware upgrade and hit the reset button for 30 seconds and everything went well until I went to restore my personal settings. When I went to the router page it asked for a user name and password but the old user name and password don't work so I am locked out and can't get to the restore page.
View 3 Replies View RelatedI recently re-installed Windows 7.When I try to access the network set up between my PC and Laptop I get a box requesting my name and a password.
View 6 Replies View RelatedI am a medical student and I use my college wifi to download torrent files via utorrent. Earlier they have blocked torrent sites, So... I use to download the torrent address via my 3G Dongle and then open it in the utorrent to download the whole file ( 4 GB or 8 GB size). The WiFi provides about 1-2 Mbps speed and the files ude to download very easily . But, now along with the blocked site , ... the utorrent is not catching speed.
View 4 Replies View RelatedI had a custom device/computer on my network that was hacked from hong kong. It's one of those things where I seriously think the chinese have built a back door into it when they built it or something because everything was secured and monitored.The device runs it own OS or something like that I guess you could say. It can also run it in standalone mode broadcasting it's own signal. Once I figure this out I may not put it online anymore but thats besides the point right now. When it was hacked I'm pretty sure the port it uses to connect was changed from 80 to 591. When it runs in standalone mode I can connect to it but I am unable to actually access it's proprietary graphic network interface. It sends out UDP every few seconds or so and basically I was trying to search for some type of udp broadcast monitor and have tried using network tools such as netstat, port scanning, multicast, etc on all of the big three OS's because sometimes it seemed to finnicky what it wants to connect to. I've tried to let it connect back to my router again which it seems to do, but is then denied access and I think it may even have a trojan or somethng so I don't want it to that but if I have to to access it again I will.In standalone mode I've it usually trys to connect on 192...5 or 192...7 and I've tried to get through 591, 23, 80 etc. multiple times with no luck.
View 11 Replies View RelatedI have a computer through my old school and i still cant get into the main part of the computer to change my password etc; How do i unblock it?when i click it, it says; please contact system administration but i cant and they wont tell me.
View 1 Replies View RelatedDuring installation of CM 5.1.4 on Windows 2003 Enterprise Server, I get popup windows "Stop All Programs". I checked Windows Service console but have been unable to determine which processes may be holding these files.
[code]....
I've been using the trial version of a product called Folder Lock on another computer than the one I'm using right now to type this message. I got a little too enthusiastic about locking away folders into Folder Lock on that other computer, and I think I locked away Folder Lock itself.In the past (before this problem developed), when I clicked a Folder Lock icon, it used to prompt me for the Folder Lock password, which I would then input, and then Folder Lock would open, and I could lock and unlock folders. But the problem is that now I don't get prompted for the Folder Lock password. I get a message (from Folder Lock) that says, roughly, "you may not have permissions to carry out that action." So even though I have the Folder Lock password, I can't open Folder Lock, because it won't prompt me for the password, and just says I don't have permissions.I also locked into Folder Lock my downloads folder on that computer, and apparently folders or icons that used to allow me to access the internet on that computer. I can no longer access internet from that computer.I'm wondering how I can get Folder Lock to prompt me for the password, so I can open Folder Lock. I would like to unlock all the folders I locked -- including if I locked Folder Lock itself! I locked away a lot of my important stuff. I wonder if I should do a system restore to a date before I installed Folder Lock, but I wonder if the system restore might fail to delete Folder Lock, because Folder Lock might prevent its own deletion. I have Folder Lock 7. I have Windows 7.
View 3 Replies View RelatedMy wife and I Security Enabled our wireless network several months ago.We recently moved, and after transferring Internet service, we realized we'd lost our passkey.My wife's laptop has, after one failed attempt to connect to the network, refused to even show the network as an available connection.We currently have the router set to broadcast SSID.We have restored factory settings on the router and completely revamped the security setup.We've removed all other networks in the area as optional connections on her computer.We also replaced the ethernet cord to my desktop because the old one started erratically disconnecting.Nothing's worked.My wife's computer is a Dell laptop using Windows Vista.
View 6 Replies View RelatedI have installed a SumvisionSWV322P Wireless PCI Adapter in to my desktop and have configured it to run on my existing home network: I can connect no problem but after about 10 mins my whole desktop just locks up: The only way I can get out of this is by re-booting by turning the machine off completely by the on/off button. My OS is Windows XP Professional version 2002 SP3:
View 1 Replies View RelatedI have a Linksys wusb54gc, after downloading driver and install, system performance changed. Tried several fixes suggested at another site which failed Cannot delete (access denied) Trying to remove through control panel error "critical file missing" win xp os. Would like for this to work as it had on the computer it was originally purchased for. "gina.dll" interferes with the os.
View 2 Replies View RelatedWe are using ASA5520 as our VPN concentrator and has configured IPSec authentication using digital certificates with Microsoft CA for the remote access VPN. The AAA server used for remote user authentication is Windows Active Directory. Screenshot of the AAA configuration is attached. The problem we face is that the "Login DN" account (marked in red box in the screenshot) is frequently getting locked out in the active directory. I have confirmed that the password is the same on both ends and the account is not used any where else.
The NTP server configured for the VPN concentrator is the Active Directory itself but no accounts are configured (not required) for updating the time service in the concentrator.
I am currently running cisco ACS 5.1.0.44 and use active directory as the main authentication identity store to allow network administrators to have access to network devices in my organization .As per the established security policies in my organization , the ACS has to disable any account after 3 failed login attempts to any network devices .i have gone through all the settings oN the acs but couldn't find where or how it is done .
View 3 Replies View RelatedI am working on a Drupal site which is on a virtual server (the way it's been explained to me). I've been told I need to work with it through webdev. So I can copy a file off the server and onto my local machine. I make my edits and then try to upload it to the server. I get locked out with the message: Error 0x80070021: The process cannot access the file because another process has locked a portion of the file. I have tried shutting down my code editor, opening and closing the connection, tried different methods of reaching the server (Cyberduck and through Window's map network feature) to no avail. What can I do?
View 1 Replies View RelatedI am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies View RelatedI need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies View RelatedI've a router for my iPhone which I cannot seem to get it working properly. This is an old router i bought 3 years back.I'm able to get my iPhone to find the SSID of my router, get connected, but the speed is really slow... It works flawlessly when I first start up my router, after awhile, its so slow, i need to switch to my 3G.I'm wondering it could be the setting issues. Any appropriate settings like the channels, long/short Preamble, transmission rate, basic rate, 4xs mode?
View 6 Replies View RelatedI setup a password for my router configuration. But i forgot it.
View 1 Replies View RelatedHow can i access a LAN IP through WAN
View 1 Replies View RelatedI have a nat configuration to apply on a 8.4. I am a bit confused.On a ASA 7.0 the configuration is as such static (inside, outside) 10.102.247.0 10.102.247.0 netmask 255.255.255.0Basically, I want a bidirectional nat .. for users to connect to the inside network using the real IP.object network Delta subnet 10.102.247.0 255.255.255.0,object network Delta
View 0 Replies View RelatedI'm trying to run a server for a java application called mekwars. The program needs ports 2347 and 4867 open. I have obtained an ip address from my ISP and registered with dyndns. I can ping my public ip address (my router)I can access my server from any other computer in the LAN. My router is a Zyxel p660hn-T1a. I have configured port forwarding of both ports to my server.I have disabled the firewall in the router and restarted it.My server is running CentOS 6. I have opened the ports in the server iptables, I don't think this is the issue as I can connect from my lan to the server.When I try to connect (from within my lan) to the public ip address of my server the program tells me it cannot find the server. I can't telnet to port 2347 and nmap tells me that the only ports that are open are 22, 23 and 80 ( I believe this are open by default on the router to allow remote management).I can telnet from the lan. My networking isn't great and I'm used to having an "ip passthrough" option on the router to assign to my server. I do have it set as the default router in port-forwarding so I had hoped this would be a similiar option.
Do I have to set a static route in addition to port forwarding or could I have port forwarding configured incorrectly? I'm also considering the router may be at fault and I've emailed my ISP to make sure they're not filtering the ports before they reach my router.
'm having problems accessing the configuration utility of the *second* router in my daisy chain. Here's my setup. I have one router (router 1) on ground floor which gets internet from the modem. That router is then plugged into the LAN port of a wireless router upstairs (router 2). My laptop is then plugged into another LAN port on router 2. This allows me internet access as intended. But I'd like to log into the the configuration utility of router 2. But when I type the IP address of router 2 into my browser (192.168.1.1), it takes me to the configuration utility of router 1. Router 2 is out of the box--I haven't done any configuration to it (for example, changing its static IP address).
View 2 Replies View RelatedI have a wireless Netgear extender, and can not find set up page..Can't access own router configuration page
View 3 Replies View Relatedwe recently got a new router and added it to our network... works fine the problem now is that i'm trying to add some other ip addresses to access wireless internet (for security reasons the wirless internet is available only to one set of ip addresses) but now that i try to access the router config to get that ip address in i cant access the router config. i try multiple addresses but still nothing. i try to find the ip using cmd but it just gives me tunnel 000000000
View 4 Replies View RelatedI have 2 cisco 1841 routers the one is connected to my local network and the other is the stub router and it only has 2 fastethernet interfaces. fao/1 connected to the local network and fa0/0 connected to the internet and to the other router. How can i configure NAT on the fa0/0 which is sharing the internet and local network
View 1 Replies View RelatedRecently i brought D-Link DIR-524 wifi router. somehow i am able to connect to internet. But i am dont know how to block it for other computers. i am new to networking. How to configure the D-Link DIR-524 wifi router.
View 7 Replies View RelatedI've been using DIR-600 wireless router since an year. But, after having a factory reset i'm having a strange issue. When i'm configuring the router in the Dlink page(192.168.0.1 now i changed it to 192.168.1.100).. In that i go to Manual Internet Configuration>> then i select Static IP(Since i've been provided a static IP,gateway, DNS settings by my ISP) As soon as enter IP: 192.168.1.2,, and Subnet 255.255.255.0,,,Gateway : 192.168.1.1 and enter DNS details and press SAVE.. I get a message " Invalid IP Address".. I've set the Router IP as 192.168.1.100 and DHCP range : 3 to 199I don't know why is this happening.. I'm not able to connect to internet now from the router.
View 5 Replies View RelatedI have a serious problem with cisco 2960 router,i am using a dell dimension 3000 running a microsoft windows xp proffessional.
View 3 Replies View RelatedRegion : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : mr3040v2_en_3_14_4_up_boot(121017)
ISP : Railwire
I have an broadband connection which does not need a modem to access, i get the CAT5 inthernet cable from the provider. In case if i use it directly on my PCall i have to do is provide username and password under PPPoE and internet works like a breeze.
Now i try to use this 3040 device to use as an wireless router so that i can access internet on multiple devices. How to configure this. I tried in all the three switch options provided with no result at all..I am now using a traditional router from which i connect to Tplink 3g router and using wireless under Access point option...But i would like to use it directly as i can get battery back up so that even when there is no power i can still browse?