Lost Wireless Access To Internet
Dec 6, 2011
A week ago this laptop was working fine. However, now it will not connect via wireless to the internet. It says that it connects to the router but not the internet. I can connect to the internet if I use the wired LAN connection. I tried a restore to two weeks ago (when it was working) and it did not solve the problem. I do see in the wireless network connection status that IPv4 connectivity = local and IPv6 connectivity = local. While on another laptop (that is working and connects to the same wireless router) the IPv4 = internet and IPv6 = no network access. I think this may be the issue, but am unable to find out how to change them.
OS = MS Vista Home SP2.
View 3 Replies
ADVERTISEMENT
Oct 19, 2012
Lost internet access through server after change router LAN ip.I did every thing still dont have access to internet .and also read this post:
http:[url]....
I have a router and a server that are connected through two unmanage switches. The router has DSL service in it, and i can ping the router from server3 client through cable and 2 client through WLAN.
View 8 Replies
View Related
Mar 26, 2012
We've had no problems with our Internet before but yesterday I could only get local access connection. Neither my iPhone, laptop or home computer cud get any further than local connection on wireless.I'v tried the classic turnin it off and on (the router) and I'v tried connection with a cable but still gettin the same connection level! The router is a netgear if that means anything!
View 1 Replies
View Related
Mar 16, 2012
I cannot connect to the internet. After running troubleshooting i receive and error message."Local area connection 2" doesn't have a valid ip configuration.
[code]...
View 4 Replies
View Related
Dec 28, 2011
My mother's computer periodically loses internet connectivity. This happens regardless of the browser (IE or Firefox). She must restart her computer to get access again. This happens regardless of her internet connection. She uses verizon at her home and accesses through my wireless router when visiting. This also happens if she is on a public access network such as a hospital
View 1 Replies
View Related
Nov 23, 2012
After reset to factory settings of my Acer 6930 I have lost my internet access.Tried wi-fi and ethernet but neither find my router.
View 6 Replies
View Related
Jun 30, 2012
Over the past few days I've been having a problem with my internet connection.
I connect to my home wifi network and will have excellent signal strength, but after about 20 minutes or so, I will lose internet access, but will stay connected to my wifi network. If I join my neighbor's wifi network I will have the same issue.I will connect to a network, and while still connected, I will suddenly lose internet access (signal strength will remain the same). Switching networks doesn't correct the problem.
When I lose internet, I can disconnect from the network and reconnect mere seconds later and will have the internet access back again.I have reset the modem/router and my computer numerous times but the problem does not go away.
View 3 Replies
View Related
Dec 29, 2012
I can no longer open a http or https connection to the AP. I do have ssh access and I can log in with full privileges.
I was using the Web interface a few days ago and it did something strange during an update. The display of the web page became corrupted and no longer responded to my input.
I restarted it from an ssh session and I have also power cycled it via the power injector. Neither method has worked.
What should I do next or what additional info can I provide from an ssh shell?
Physical access is very difficult. It requires a 30' ladder after 10 p.m. So, I would like to avoid that if possible.
View 7 Replies
View Related
Jul 7, 2011
I FORMATED THE HARDRIVE AND REINSTALED XP NOW NO INTERNET AND NO AUDO I USING A LATUDE LAPTOP
View 1 Replies
View Related
Mar 20, 2013
Region : UnitedKingdom
Model : TD-W8980
Hardware Version : V1
Firmware Version : 2013 firmware update
ISP : PlusNet
I changed the local port to 8080 for accessing the web logon page (i.e. 192.168.1.1) instead of its default port 80.
[code]....
View 2 Replies
View Related
Aug 4, 2012
Lost wireless icon in internet connections
View 1 Replies
View Related
Jan 19, 2012
At power on and off on my laptop, the wireless internet connection is lost on windows 7.
View 1 Replies
View Related
Aug 31, 2011
i have problem with internet notconnected router
View 1 Replies
View Related
Jan 23, 2013
my compaq presario CQ50 suddenly will not connect to internet.my router is a linksys WRT54G.
View 2 Replies
View Related
Feb 24, 2013
I have lost my wireless internet connection it has been working perfectly, I phoned Sky and they say I will have to speak to dell to see where my internet has gone. I have a Studio 1745 Laptop. Is there a manual disable button on my laptop that I may have disabled by mistake.
View 1 Replies
View Related
Sep 5, 2011
I use a D-Link DWA-552 Xtreme Wireless-N PCI adapter on my Windows XP Home SP3 desktop computer that has been working flawlessly for months, until last night when it suddenly stopped being able to connect.I was just on the web last night doing what I normally do, and all of a sudden out of no where I lost internet connection and I couldn't get it back. I've tried resetting the router downstairs, I've tried restarting and shutting down the computer, and did three system restores (that all failed anyway), and none of these things are getting my connection back. Now also for some reason I can't even open up my network adapter's wireless network manager anymore because it closes itself not even a second after I boot it up.The modem and router downstairs look perfectly fine and all the other computers in the house, even the laptops, can all connect but mine, so something must be up with my network adapter.
View 14 Replies
View Related
Oct 28, 2011
I have the latest flash installed. I am making use of all the options available to this router. USB drive set up as a file server, both radio bands have devices which attach. All wifi security is wpa2 with a complex key string. Also have pc’s attached to all lan ports. I also have all the wireless devices registered on the mac address filter for access set to enable/allow. I have a total of 9 mac address in the list. One lan device is on the DMZ. One address is reserved. Not sure what other details you need.Router is used for online gaming, video streaming, and typical internet browsing.
View 1 Replies
View Related
Feb 9, 2013
Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4300_V1_121226(Unifi)
ISP : Unifi
Recently my router have been experiencing an issue with internet connectivity with Unifi.I will be able to connect to Unifi, the status is "Connected". However after some time though, like 5 - 10 mins, I will be no longer able to browser any pages or get disconnected from online games. Checking through ping tests, I can see that I am unable to get a response. Checking the router shows that I am still connected to Unifi. After a minute or so the connectivity is restored, but the issue happens again as before. This happens with both wireless and cable. Attached is a sample of the ping test result.
Things I have tried:
Updating the firmware to the latest version
Re-configuring the modem
Re-setting the Unif credentials in the router
Downgrading the firmware
View 4 Replies
View Related
Jul 8, 2011
i bought a WRT160N router
I connected the Router to the modem, and all the wired connected PCs were working perfectly.But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection droppedThe only way i had to fix this was by making a Hard Reset.after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
View 3 Replies
View Related
Dec 4, 2012
I have a Linsys E3200 router for almost a year. It's been working fine until recently. It kept losing internet connection every a couple hours or even shorter. I have to power cycle the router in order to make it to work. However, sometimes that won't work either. I also tried to restore the router to the factory default but that doesn't seem to work.
I have updated the router with the latest firmware (1.04). I am using a cable connection and it never gives me any problem if I just connect my computer to it. I also test my network with another old netgear router that works just fine.
View 9 Replies
View Related
Jan 30, 2013
Today we lost access to our external hard drive (T:). We got the error "An error occured while reconnection T: to \192.168.1.254share Microsoft Windows Network. The local device name is already in use. This connection has not been restored"
Do I have to Re-Map that Network Drive?
View 19 Replies
View Related
Oct 30, 2012
Just implemented a couple of replacement DNS servers so decided to test by disabling existing Server DNS services only (10.0.0.21)Two problems arose from this, first was I lost access via the ASDM, second was remote access failed. The Cisco VPN client worked but RDP could not find the remote access Server.I've replaced the DNS settings everywhere I could think on on the ASA so decided to check the running config and noted these lines that refer to old DNS.Would this suggest the cause for the RDP, although looking at the various group policy areas on the ASA I could not locate any reference to 10.0.0.21/22, am I missing something?
View 1 Replies
View Related
May 17, 2011
To put it simply, my parents live far enough in the middle of nowhere that they have no access to high speed internet. Of course, there are always wireless solutions, but the options around here are pathetic and comparable to dialup. They were content with this; I moved back in with them for the time being and am not.y solution has been to dump just shy of $1,000 into a point-to-point wireless bridge setup that claims to have a range of 5 miles non-line-of-sight. I have one antenna set up four miles away on top of a building that has high speed internet.Unfortunately, I was a stupid fool and set that end up without enabling security, thinking that it wasn't a big deal. Nobody in that town has a mind for anything but farming and drinking. That was my mistake. Some asshole set a password and forced me to do a factory reset on the access point and now I can find no IP address. It's like it only reset halfway to factory defaults or something
View 6 Replies
View Related
May 21, 2007
A few days ago I had to reinstall my notebook and therefore I lost my network settings. I want to reconfigure my Linksys Wap55AG to let it use a new WEP key but I cant find the software to do so ANYWERE on the net.
View 5 Replies
View Related
Jan 9, 2012
I bought a WRT54GP2 independently of my ISP/VOIP provider so I could have an all-in-one router. As my provider would not provision the VOIP side I disabled provisioning and set up the voice settings myself and it works perfectly.I was reviewing the VOICE settings side and under the SYSTEM tab there were settings for Administrator Password and User Password. Researching on the Net it seems these should be set to strong passwords which I did but then found trouble moving from the main part of the router configuration to the VOICE tab as I would get a message about a non-admin account not being able to administer the voice side. Via clearing the cache on my browser and restarting the router/browser I managed to get back into the VOICE config tab and immediately removed those two passwords. Seeing the settings under the SYSTEM tab it looked to me that the router was open on the WAN side on port 1880 so I disabled the web server and web server admin options thinking these were only related to the WAN side not the LAN side.
I now find out that I can no longer access the VOICE tab as the router immediately disconnects from the browser.I've tried contacting my ISP/VOIP provider but they seem to be unable to assist and have had no luck with Linksys support either as all they want to do is pass it back to my ISP/VOIP provider saying they are the one to reconfigure it but I'm the person who did the config (and also shot myself in the foot incidentally). If I could only reset the voice side of the router back to factory defaults I would be fine but, unlike the WAG310G, there is no option to do this, just the option to reset the WAN/LAN/Wireless side to factory defaults. I've tried pressing the reset button for 30s and reset via the menu option but neither reset the voice side. Surely there must be some way to do this even if it involves opening the box up and connecting a jumper or something.
View 9 Replies
View Related
Mar 1, 2011
When I try to connect to the internet I get IE cannot dislay the webpage. All connections show that they are working fine. I did the repair option for my LAN, it states that it is working & shows that it's connected.I tried to sign into MSN & got no connection. I ran the repair option & got a DNS & Keyports warnings.I am running Windows XP on my home computer
View 2 Replies
View Related
Jan 26, 2011
My computer is part of domain.I have one LAN connection. IP address 172.100.40.70 ,subnet Mask 255.255.255.0, Default Gate Way 172.100.40.1Another is one internet connection through bluetooth PAN IP address 192.168.0.103, subnet Mask 255.255.255.0, Default Gate Way 192.168.0.1.Problem is when I connect to LAN, internet connection is lost. If I take out LAN cable or disable LAN, I get the internet connection. I want to keep both LAN connection and bluetooth PAN internet connection.I must keep LAN IP address without changing.
View 6 Replies
View Related
Dec 23, 2011
The computer lost internet connections. Other computers in the house are fine with wireless and the direct connection.This computer I am working on is the one directly connected (not wireless).I tried the connection on other computers and it works.When troubleshooting, it indicates it lost the drivers so we downloaded the correct drivers and installed them on the computer. It indicates it has the updated drivers now. Funny thing is when you start of the computer the error message on the screen is Installation or Upgrade Error A problem occurred during the upgrade process.you must restart your computer. After it restarts, the Webroot upgrade resumes.I am concerned as my daughters computer has the same error message but her Internet connection still works.Seemed to me that Webroot could be a potential problem. Since we can't download the latest version (no internet and can't use disc we have as it tells us it is outdated) I tried to uninstall using WMPinfo.xml to finish the uninstall.I got an error that indicated - "The InstallAware Wizard for Webroot Software has failed: "WRConsumerService stop failed with error 2 and kill failed with error 128". If you continue to have trouble, please click the link below for assistance. And the link is titled Uninstall but without internet it is worthless. It uninstalled the Webroot SecureAnywhere file but it doesn't remove the Webroot Software. [code]
View 14 Replies
View Related
Dec 6, 2012
I was trying to browse the internet earlier, and I randomly just lost my internet connection. My homepage loaded up just fine, but then I tried to go to another site. It was taking a while to load. After about a minute a page finally came up that said "Server not found" (I use firefox). I can't get on any websites now and I can't get internet on any of my wireless devices either. When I right clicked my network icon on the toolbar and clicked on diagnose and repair it said "There may be a problem with the DNS. Windows attempted to find the well known host www.microsoft.com using dns. The server responded that the name was unknown." I have Windows Vista. Now I have no idea what I could have done. I didn't do anything out of the normal, just tried to go to a website that I frequently visit with no problems and this happened. This is what I get when I type ipconfig/all in cmd prompt. [code]
View 14 Replies
View Related
Dec 16, 2011
I dont have an internet connection through my computer. This one tells me error 106. I have 3 computers hooked through the same router. So, I know I have internet, as I am writing this now. But for some reason, that computer is now telling me I lost the internet connection. I have tried unplugging everything, restarting the computer, and nothing has worked. I dont know how to get the internet back on that computer.
View 2 Replies
View Related
Aug 18, 2011
Whenever I restart or boot my computer, it loses internet connection (Local Area Connection Unplugged). I need to unplug the cable connecting my pc to the modem and replug it until the green and orange light comes on on the area where I plug the cble to the pc w/c means that there is already internet connectionSystem:Win XP sp3 OSGigabyte S-series motherboard ma74gm-s2Amd Athlon X3 processorMotorola SURFboard SB5101U/SB5101N Cable modem
View 8 Replies
View Related
Nov 13, 2007
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
View 9 Replies
View Related
Jun 22, 2007
I bought the wap54g access point.unfortunately i have lost the installation cd.is there a way to download the drivers of this device?
View 4 Replies
View Related
