Having internet trouble where my connection keeps dropping randomly every minute or so. Tracked it down to my router. Checked my router log and found this: Quote:
Oct 10 07:31:43 syslog: ERRO: MC-Router API already in use; Errno(125): Address already in use
Oct 10 07:31:43 dhcp client: bound IP : 67.240.122.xxx from 67.240.96.1
Oct 10 07:32:16 dhcp client: deconfig: lease is lost
Oct 10 07:32:17 dhcp client: bound IP : 67.240.122.xxx from 67.240.96.1[code]....
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1 FastEthernet0/1 is up, line protocol is up Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
i'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
I configured dmvpn at cisco router 2900. one hub router and 3 spokes. all of them are working normally but tomorrow i see one error at at one spoke router.
error: Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license
I have a ASA 5510 behind a 2911 router. I've trying to configure a remote access and site to site vpn tunnel. I've started on the remote access, and I have it setup, but I'm getting this error message with trying to authenicate from the VPN client (412 error)?
Nov 11 09:52:45 [IKEv1]: IP = 68.51.100.192, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + HASH (8) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 428 Nov 11 09:52:51 [IKEv1]: Group = tfx-tg, IP = 68.51.100.192, Duplicate Phase 1 packet detected. Retransmitting last packet.
i have a SMC8014WG-SI Router and its gateway is 192.168.0.1 but when i type it in the router doesn't appear at all , just says that the page cannot be found. i like portforwarding and need to be able to login the router to do so.
I've had my DIR 615 router for quite some time. The hardware version is C1, firmware 3.01 originally. It's been fine for the most part (asides from connection issues now and then with the internet - which we rectified by unplugging modem and/or router). A couple nights ago we had a storm and the next morning the router would not connect to the internet. I tried unplugging the router and modem a number of times but could never establish a connection. The internet globe LED was originally orange but after I cut off the power, it never came back on. I tried a number of different cables between the modem and router and could not fix the issue. I bypassed the router totally and the internet works fine. After a lot of failed attempts, I decided to reset the router and reinstall it with the disc. I followed the instructions and kept getting error 322 that the router could not be found. I tried 3 different computers and 5 different wires to fix the problem but to no avail. I kept encountering the same error on each computer. Since the router can't be seen, I must bypass it totally to get any internet access so trying the online setup doesn't work because I can't connect to the router and then to the modem since there is no internet access. So now I'm stuck. I'm not sure if my router is damaged from the storm. All other lights work (LAN and wireless icon) but I can't get any internet access through the router. I'm not sure if I should just go buy another router or not. The installation checks out fine until connecting power to the router and then it can't be found.
I am running windows 7 and vista on different computers and laptops and used setup 4.1.7141.2
ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
xxxx uptime is 2 days, 16 hours, 1 minuteSystem returned to ROM by power-onSystem image file is "flash:c880data-universalk9-mz.150-1.M4.bin"Last reload type: Normal Reload
This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:[URL]
Cisco 881 (MPC8300) processor (revision 1.0) with 236544K/25600K bytes of memory.Processor board ID FHK144973KN
5 FastEthernet interfaces1 Virtual Private Network (VPN) Module256K bytes of non-volatile configuration memory.126000K bytes of ATA CompactFlash (Read/Write)
I was using my internet on my Acer Windows 7 operating system wireless just fine on Monday. I tried to use it on Tuesday and could not connect to the internet wireless any longer. I get an error message next to my network stating ""The settings [COLOR=green ! important][COLOR=green ! important]saved[/COLOR][/COLOR] on this computer do not match the requirements of the network"I have never encotured this kind of problem before. I proceeded to call Comcast who did all kinds of trivial beginner troubleshooting such as restart the router, restart the modem turn on and off the computer.
Earlier today I was attempting to do something with my router settings and ended up reading on the internet that I needed to do a hard reset to access my router interface - when I typed in the IP address, it came to a "could not find server" error in the browser. After doing the hard reset (holding down the reset button for 30 seconds) I was able to access the router, and adjust the settings. After doing this though I was no longer able to connect to the internet through the router, although the router is sending out a signal (it says connected to linksys but "no internet connection"). I am currently connected directly to the modem right now using my laptop.
TL;DR: Did a hard reset on my router, now it's sending out a signal, but no internet. Modem still has internet, as does the router, (the internet button is green).
My quickvpn setup has been working great for a few years but it stop working recently with the following error message in wget_request_error.txt: HTTP request sent, awaiting response... 501 Not Implemented 20:10:10 ERROR 501: Not Implemented.quickvpn hangs on the dreaded verifying network stage.Checked VPN router logs and also quickVPN client logs and confirmed the tunnel has been created successfully. However the ping was unsuccessful.I look through the forum and confirmed that my quickvpn user account and password only contains alphanumeric characters.
I recently received these routers and after the first reboot I changed the user id and password so it does not lock out...After configuring my routers for installation, upon bootup I am getting this message scroll down my screen
I have a Cisco 3945 Router and when we try to add the same into the Cisco Works it gives me an error saying " CM0056 Config fetch failed for 192.168.xx.xx Cause: CM0204 Could not create DeviceContext for 1238 Cause: CM0206 Could not get the config transport implementation for 192.168.xx.xx Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.
We are using LMS version 2.6. Any info on the latest router 3945 with support or not.
After formatting the CF, the router is able to see the flash without a problem. I copied files to the flash - still able to see the contents okay. The problem ia that if i restart the router with the new flash, i get this error:
Jan 22 17:44:12.454 MSK: %SYS-5-CONFIG_I: Configured from console by bt_admin on vty0 (10.10.10.44) Jan 22 17:45:41.847 MSK: %SYS-5-RELOAD: Reload requested by bt_admin on vty0 (1 0.10.10.44). Reload Reason: Reload Command. System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) Technical Support: [URL]
If all you have is a high end cisco router available, can you plug in hosts to the router ports, and configure them within the same subnet? (When I try to configure ports within the same subnet, I receive a "same subnet" error.
I have a Dell XPS 430 desktop and a Netgear DGN2000 modem/router. My ISP is Zen. The router is connected to the PC by an ethernet cable.I have had no problems accessing the internet for years until a couple of days ago when the monitors on the info bar show a triangle with a yellow exclamation mark. The Windows Diagnose and Repair reports - Error 815. The Broadband Network Connection could not be established because the remote server is not responding.My laptop with a wireless connection to the router as no problem connecting so I assume the router is OK.
Windows 7 64 bit with latest Windows updates Microsoft Security Essential with latest updates Zonealarm Firewall Free with latest updates Windows Firewall off and can't turn on, error code 0x80070724
Problem:Yesterday, I installed VMware Player and XP Mode to play a legacy game; also, some Automatic Windows Updates were applied. After the Windows Update's all done, it prompted me to restart every 10 or 15 minutes, even after I chose Postpone 4 Hours every time. Probably one hour after, I closed VMware Player and restarted Windows. Later, I found my Internet didn't work anymore.
Troubleshooting Attempts:I had already did the ip stack reset, removed VMware Player, restarted the wireless router, restarted WiFi, reenable WiFi adapter, reinstalled Wireless driver with latest driver, System Restore to the day before (System Restore said it didn't work, but Windows reboot said it has been restored), disabled the Internet sharing (I didn't turn it on, I guess some program like VMware did it), removed Stored Wireless Network Profiles and added later.Windows 7's network troubleshooting found no problem.
Current Situation:The home wireless network is working properly for sure, because both my phone and others' laptops connect to the same WiFi and work properly.I installed Ubuntu 12 on this same laptop and connected to same WiFi to go online.WiFi is shown to be connected and working. I can ping and connect to the wireless router (192.168.2.1), but unable to go to any website.
--------------------------------- C:Usersanluo>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : MyPC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No
I have an E3000 with firmware v. 1.0.01 build 6. I am trying to upgrade to the latest firmware version. I downloaded the file, and when I went to install from the web page I got the error message: Not enough memory available. I tried from 2 computers and got the same message.
Lately, Ive been trying to change my router DNS to OpenDNS. Somehow, after changing it, I couldnt access the router page at 192.168.0.1, getting the error 500 message. I unplugged and plugged the router with no effect. Im using a dlinkddns.com dynamic IP, and have a few ports forwarded for my DVR. The router model is DIR 615. want to change the DNs for speed and filtering purposes.
I've just recently started to get this error, and I'm not sure why (I have no expierence with routers whatsoever). I have noticed, that whenever this happens though, that my NAT type for my xbox goes strict.
I have a problem with my router, WRT54G2. I was upgrading my firmware when my computer froze up, so I had to exit. Afterwards, I could not connect to the web based setup page anymore. I did a factory reset and installed it again with Network Magic and set up my wireless key. It is working now however, I cannot get into the web based setup page. Whenever i go to 192.168.1.1 and enter my info, it just says 500 Internal Server Error. I was always able to access this page, now I can't, so I assume it's not working because of the interrupted firmware update. I do alot of mac filtering and I limit the amount of IP addresses my router gives out so if anyone hacks my security key, they still won't be able to connect, so accessing my router setup page is important to me. I have reset (hold down reset button for 30 secs - 1 minute) the router many times and still nothing. I mean, the router still works. My brother and I can still connect with our laptops, I just can't get to the web based setup page.
Couple weeks ago installed my ea3500. Am loving its ease of use and features. I also created a smart wifi account. yesterday I tried to remotely log in and got password errors. I have tried all my small arsenal of staple passwords. No go. Today I called Linksys for support. After getting transferred around then having to explain the difference between router local and online passwords, the customer service rep had me create a new account telling me I had not previously done so. Also said if I had, then I wouldnt be able to create another since a router can only have one account associated with it. What the heck, worth a try.
Now, when I try to log in to the web based settings I get 'Unexpected Error 2120.' If i try to log in from my SmartWifi iphone app I get 'No associated networks. the linksys smart wifi account specified does not have associated networks.'
Just to clarify, I can log in locally to the router, but cannot via my smartwifi account.
