Make Static IP Without Losing Any Functionality Of Desktop?
May 16, 2011
Im running a fairly simple server from my own desktop. However my desktop is connected to the internet via Wifi. When i make my static IP i am still conected to the internet. However I cant load any pages in mozilla firefox. Though! I can still talk to people on skype and Dolby Axon voice chat. how do i make the static IP without losing any functionality of my desktop, because it is my desktop, I use it for other things.
I'm trying to set the various computers in my house to static IPs. When I do, the apprear to still be connected to the home network but lose internet connection. I'm using a Medialink wireless router, but I'm trying to set the hard wired lan connections, not anything wirelessI go under ipv4, set:ip address: 192-168.0.100 (or 101, whatever)submask fills in to 255.255.255.0Default Gateway: 192.168.0.1I also went into the router setting and change (dchp?) to only automatically assign from 192.168.0.120 and up so nothing conflicted.
I have a dell desktop and a toshiba laptop with a Linksys wireless N broadband wrt160n v2 router. I have the desktop hardwired to the router along with my dsl. The desktop pc keeps lossing it's IP. I tried to get window to fix it but no matter what I do, I can not get the desktop PC to see the internet. All the lights on the router show the pc are there. I can hook the dsl right to the desktop and can get to the internet but then I not using the wireless router. If I keep rebooting the PC and router I can get luckly have get the connection but if I walk away and come back later the desktop can no longer see the internet.
I have 3 Dcs-3420's on the same network same static ip setup and they never have issues. Im testing 1 942L, I've upgraded firmware to1.11, but periodically the camera loses its ip address which is weird because it is set static. My wireless is set to Mac address security. Now camera is outside in a shaded area, over night the camera worked all night, this morning it has reset three times. Additionally, each time it resets/losses ip address it also loses the manually set time.
I leave on one of my computers on all the time, an Acer desktop with Windows XP. I also have two laptops. I have Verizon DSL and a linksy wireless G router. When we have a power outage the Acer desk top loses it's internet connection. Trying to reconnect the connection takes hours. Even when we finally get it back we have no idea how we did it. The laptops which of course were off have no problem.
I have a Sony VAIO desktop, 5 years old running windows XP. Recently, I started getting ntoskrnl32 missing and refused to boot. My local computer guy said that it is a hard disk problem and ended up putting new hard disks and reinstalled XP. But I keep internet connection after about 5-10 minutes. If I disable and enable "Local Area Connection" it works for sometime and stops again. I have a Cisco wireless router that I use. I use that to browse with my iPhone as well.
My question is how can i turn this adapter that i get internet from for my desktop INTO wifi so i can use my tablet?right now the desktop is the only computer with internet since it has an adapter.what do i need to make a WIFI signal from the computer? is there a usb stick or router i can buy?
I have DSL on my computer which runs windows 7, using verizon's Westell model 7500. My wife's desktop computer in another room runs windows XP. I purchased a new Linksys USB adapter model N600 which includes an installation disk for her computer. My question: How do I get them to work together so she also has internet connection for her email, etc???
Have just acquired new used HP desktop running Windows Vista. System has a Broadcom NeXtreme Gigabit Ethernet card installed, which gets me to the internet OK when using a LAN cable from wireless router. But I can't make wireless connection. Vista tells me that I need a wireless network adapter.Am I missing something? Is it possible to change some settings to get the Broadcom card to go wireless? If not, what sort of adapter is needed, and is such adapter external or will it have to be installed in the system box?
My Dell Studio 1558, specs: Core i5 2.4Ghz, 4GB DDR3, 640GB HD, Radeon 5470 has a very weird problem. Occasionly, either once a week or twice a day the network functionality will literally dissapear. The icon still displays on the tray but when I click it nothing happens. If I try and connect to the internet it will say there's no internet connection. Also if I try and open the Network and Sharing Centre explorer stops responding and has to be restarted. If I try and shutdown the laptop it will just hang on the Shutting Down splash screen and has to be forced off. The laptop is still IN warranty however I want to fix it myself as I cannot face Dell
I have a DIR-651 Router (I could not find one for the 651) and I would like to use it as a router only.Is there a way to disable the wireless functionality.
We need to upgrade Ios in a 6509, the reason for we need to upgrade IOs is that we need implement the command xconnect in a interface. The current version of Ios not suport this comand.
How do we select the new IOS that suport this command?, ..we see a long list of IOS in the software download section of 6509, but not sure which one to choose..
With lms 3.2 during installation we can choose what to install i.e. not install DFM or IPM. How can we do this in the new release 4.0 of the LMS bundle. I saw no options for it during installation of the new server.
Using the VRF- Lite functionality on Cisco 3750G's (WS-C3750G-24T-S), I've got a situation currently with a set of 3750's running inter- v LAN routing for around 80/90 connected sub nets (140+ gig ports). I'm looking in the coming week at creating a new VRF and enabling OSPF for that VRF while leaving the existing routing arrangements in the Default IP Routing Table.
I'm in a situation where I can't replicate the live config into a lab to test the impact / implications of enabling / creating VRF's. I know the 3750's have a very small support for VRF's (24 if I recall) but I only plan on using 2 or 3 max currently.
I am currently looking at the suitability of replacing an 'airbreak' firewall with 2 new ASA 5505'S.One stipulation i have is that i require to connect the third party that is currently using the 'airbreak' solution using a secure iPsec VPN.I have both 5505's that were supplied by the third party, but i believe i may need a new fireware upgradeI am using ASDM 6.4.XX and the ASA's have firmware 8.4(2) and a basic licence.Am i correct in assuming that the VPN wizard functionality is missing because of th firmware installed currently on both of the ASA's? or am i looking in the wrong place?
I have done a fair amount of research an can see earlier versions of ASDM wit the VPN wizzard so can only assume it is down to the firmware.i see that the latest version for the ASA 5505's is 8.4.4 and was wondering if this will provide me with the functionality i require as it does mention in the documentation that it does support the clientless VPN options. What part number ASA5505-BUN-K9 relates too in relation to firmware for the ASA's? [code]
Well I have been back and forth on this a while now...I have a 6513E chassis that is getting prepped for prod. I am currently testing sso functionality and I can only get it to work using the following images on both Sup Cards.
s72033-adventerprise_wan-mz.122-33.SXI5.bin
If I try any other image, smaller or bigger in size...it forces my Sup card in mod 8 to recycle " proxy request from peer ". I have tried K9 images and non K9 images. Here is an output from sh redundancy.
Redundant System Information : Available system up time = 4 minutes Switch overs system experienced = 0 Standby failures = 0 Last switchover reason = none [code]...
the " password recovery functionality is disabled " service is running on the system .
im trying to access rommon in a Cisco 851, with not much success, i am sending a break after the image is loaded ( in the time frame that is allowed for that) .
We just purchased this device and was curious if the firmware 3.0.2.0 or 3.0.1.0 has the CLI functionality like the Sx300 models with 1.1.2.0. I find it easier to configure via CLI then the WebUI.
After years of flawless networking performance, computer cannot cannot detect, view or connect to available networks/devices. Wireless network icons/options not present. In "Network Connections", only Local Area Connection appears, and this is used to connect to the internet. Wireless functionality is enabled. Firewall disabled.
Aside from the obvious differences between these two NAS`s (processor speed, max users, max groups etc) what are the actual real world differences in functionality between the two?
I`m also wondering what the `turbo` bit refers to?Any pros/cons of each??
The only way I could get my EA6500 to work as auto DHCP to my Roadrunner Motorola SBV5220 Surfboard cable modem was to disable IPv6 support on the router. It appears that the EA6500 attempts to issue the DHCP request for address assignment from the modem using IPv6. I could see the status of "Connecting" for IPv6 in the Diagnosis Reports and it would hang. Once I disabled IPv6, the modem assigned an IPv4 address and everything worked fine. However, am I giving up any functionality by having to do this? I bought this router and the WUMC710 Universal Media Connector for the 5GHz connectivity for streaming and just wondered if I'm impacting UMC performance or any other functions of the router by having to disable IPv6.
On previous cameras (eg: the 932L) we could enable the FTP function to send a snapshot image every xx seconds, set a base file name, and set the Overwrite file function. On the 942L, this functionality appears to have been removed from the code. How I can get the 942L to FTP the current image every xx seconds and overwrite the file on the destination? (just like the previous cameras) Perhaps there is a new way and I can't find how to do it?
We have an aging 2611 router that that we need to replace due to the fact that its 10Mb/s Ethernet ports are limiting our internet connectivity throughput (we have a 20Mb/s circuit).
The purpose of the 2611 router was to route traffic from multiple devices connected to a 2950 switch's VLAN X to the internet. Can we achieve this same functionality with only a 3750C-48TS-S switch? Could a static route statement on the 3750 replace the need for the router?
i buy my dell laptop inspiration n 5050 from 3 months it works fine till the last week i lost my wifi connection .i install anew windows but the same problem also i format all partitions without fixed>also i download fix it from microsoft but nothing happen
I am currently looking to upgrade and extend my home network with preference to dual band and gigabit functionality. My problem is choosing the correct hardware.I want dual band to separate the network for the kids (a PC, laptop, Xbox 360 and phones all wireless) and set up parental controls and maintain connection speeds etc. For my needs I need the network to be connected to my Onkyo AV Amp (for internet radio and music streaming only), Blu-ray Player, Sky HD satellite box (all wired) and a PS3 (pref wired) and a few wireless devices all N capable. Apart from the obvious gaming capability I would like to be able to stream HD video to the PS3, PC (wired) and laptops via a USB HDD connected for now on an access point or modem router to save on the cost of having separate networked devices.
I currently have ADSL so I was looking to get a dual band gigabit modem router to serve the kids wireless hardware whilst my current hardware is on another floor and is connected with a wire from the existing modem but I have to keep swapping it from PS3 to amp etc.In short I am hoping to have a gigabit, dual band ADSL modem router and connect to a gigabit access point (with dual band if possible) via the cable I have sent to the other floor to wire up the 4 devices. I've currently been looking at Netgear and Buffalo solutions as I've had problems with Linksys and Belkin routers in the past. Would this be possible with just 2 devices (modem router and access point) whilst maintaining decent speeds and if so can someone shed some light as to what I should get.
I am considering the e4200 Vs the Asus RT-N56U router -- if " download master" type of functionality possible with the e4200 ?(Its a little app that comes with the asus router that allows you to download files directly to the USB storage even after the computer is switched off)
I am upgrading the network equipment at my place of employment. We use Cisco C3560, 2960, 4506 and I was noticing that IOS 15.0.x is available. After doing some reading it appears that Cisco is going to a pay for the licensing functionality that you want. Do I need to purchase licenses to upgrade from IOS 12.X to 15.0.x to maintain functionality?
We purchase a new 3945 router and a NM-1A-T3/E3 card. We would like to use the T3 funcationality so we enabled the command card type t3 1 (slot1), reboot the device.After reboot the sh ip int brief command should show the serial interfaces e.g serial1/0.In this case it doesn't, it shows the Gigi interfaces and ATM1/0 no serial interfaces.I've also tried upgrading to the latest IOS from cisco.
Is the preempt option available in active standby ASA firewall setup with single context...somewhere i have read that same is available in active-active setup or active/standby setup with multiple context.If i active the multiple context mode on product environnement with two ASA5520 in Active/Standby mode, what are the impacts on the the production?
With the new firmware update, I have lost the functionality to disable broadcasting my SID after Pushed Firmware. There has to be a way to disable that information.
i'd like to know if there's a routed switch lower than 3750x? also 2960s? but have equal functionality like switchport mode access, trunking, spanning-tree, etherchannel, etc.
