Route Add Command In Windows 7 Professional?
Aug 20, 2012Each time I try to add a new route(route add 172.24.0.0 mask 255.255.0.0 172.21.0.4). I get the following error message: The requested operation requires elevation.
View 1 Replies
ADVERTISEMENT
2 NIC Cards With Windows XP3 Using Route Command?
Jun 9, 20111 computer (Computer A) has 2 NIC cards. 1 NIC card is on the LAN which connects out to the internet.1 NIC card is connected to another computer (Computer B) via crossover cable.
Assume Computer A NIC #1 IP:
1.1.1.2
Assume Computer A NIC #2 IP:
1.1.1.3
[code]...
Computer A and B can ping each other on their connected NICs. But Computer B cannot ping Computer A's network/LAN facing NIC card.Also Computer B cannot connect to the network. I cannot use Microsoft ICS due to company policy. I think I can use the route command and have a persistent route that would allow computer B to connect to the company's network. Also the bridge command also seems disabled (even when I select both connections at once).How should I configure the route command? Should I have a default route?I assume from Computer B the default route would something like this:route add 0.0.0.0 mask 0.0.0.0 1.1.1.3Does the network connection from Computer A to B need a default gateway?Are there any extra commands aside from the default route which would allow full connectivity? I'm trying now just to be able ping Computer A interface #1 to/from Computer B. But no luck. I want to statically configure Computer B with the same DNS settings, and bring it up on the domain.
Dell :: External Wireless 1450 On Windows XP Professional X64
Nov 13, 2005Is there a driver available yet for the External Dell Wireless card (model number D1450U) yet on Microsoft Windows XP Professional x64? I guess the better question is if there is a 64bit driver available for the external card yet?
View 5 Replies View RelatedNo Ip Address Using Netgear Wireless Adapter On Windows 2000 Professional?
Jan 3, 2012This is an older desktop, Been utilizing the net gear to get on the Internet for months and it was working fine,shows it is connected to ssid but ip shows up as 0.0.0.0 I have other home computers hooked up and work g so I located there ip address, can I input it myself ? If so how?
View 2 Replies View RelatedWindows XP Professional - Cannot Connect Work Computer To Home Internet
Jun 15, 2011I was recently given a computer from my workplace. I took this computer home, and put it in the place of my old one. The internet connection on my old computer has always been fine; all cables are connected correctly. However, this computer from work will not connect to the internet. The icon in the bottom right corner of the screen states that I am connected, but the internet browser claims that it is unable to display web pages. May the cause of this be related to any unique computer settings that a workplace may have on a computer in their network? Other computers have no problem connecting to the internet through the same, wired connection. The OS is Windows XP Professional.
View 2 Replies View RelatedLinksys Wireless Adapters :: WUSB54GC Windows XP Professional Compatibility?
May 26, 2009So I bought the WUSB54GC wireless adapter today. My computer's OS is Windows XP Professional. Whenever I load the disk and click "Start Setup" a window pops up that says "This version of Windows in not supported."
View 9 Replies View RelatedCisco VPN :: 5510 - Client 5.0.07.0410 Not Working On Windows 7 Professional
Sep 7, 2011I'm having a wierd issue with the VPN client installed on Windows. Eventhough it connects and receive and IP address, I'm not able to access any of the servers on the remote network.
Is there any special configuration need it for it to work on Windows 7 proffesional?
The client works perfect with windows XP, we have a ASA 5510 Version 8.2(2) is in routed Mode
Windows XP Professional 32bit - Forward Port 88 On Linksys WRT54G Version 6?
Mar 1, 2011I am trying to forward a port so i can connect to my computer because i want to stream a radio station from computer to my phone.I'm trying to forward port 88 on my Linksys WRT54G Version 6.I tried that but Boardwave audio streaming server still says it's not open!Here are some pictures: I'm using Windows XP Professional 32-Bit
Eset AntiVirus
and using Windows firewall
Linksys Wireless Adapters :: CISCO AE1000 Install On Windows 7 Professional?
Aug 11, 2011I have tried installing this device on Windows 7 64bit machine. The install seems to go fine and the device works at 2.4G.
But I purchased this unit to be able to test a clients 5GHz system. There does not seem to be any place to switch from 2.4G to 5.0G.
Linksys Wireless Adapters :: DP45SG Can't Install Drivers For Windows XP Both 32-64 Professional
Mar 19, 2011I cant install drivers for Windovs XP both 32-64 Professional. Original CD tells me for x64 OS is not supported, also, when trying to install only drivers it just can't find it. For x32 same problem - can't install drivers. I've got Intel DP45SG.
View 5 Replies View RelatedCisco VPN :: Dell Latitude E6410 / VPN Client On Windows 7 Professional X64 / Connection Fails
Apr 18, 2011we are using Cisco VPN client to access our corporate network.I have 5 new notebooks Dell Latitude E6410 OS Windows 7 Professional x64, with identical hardware configuration.I downloaded Cisco VPN Client 5.0.07.440 (64 bit) and installed it on all notebooks. It works fine on 3 notebooks, while on 2 notebooks the VPN connection fails with error:
Secure VPN collection terminated locally by the client.
Reason 403: Unable to contact the security gateway
We use a smartcard for VPN access (etoken from Aladdin)
Here an extract from Cisco log:
Cisco Systems VPN Client Version 5.0.07.0440Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.Client Type(s): Windows, WinNTRunning on: 6.1.7600...Sev=Info/6 CERT/0x63600026 Attempting to find a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600027 Found a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600026 Attempting to find a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600027 Found a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600026 Attempting to find a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600027 Found a Certificate using Serial Hash....Sev=Info/4 CERT/0x63600015 Cert (cn=<omissis>,ou=Remote,ou=Users,ou=<omissis>,dc=it,dc=<omissis>,dc=local) verification succeeded....Sev=Info/4 CM/0x63100002 Begin connection process...Sev=Info/4 CM/0x63100004 Establish secure connection...Sev=Info/4
[code]......
It seems the problem is in the certificate, but I verified and Cisco client says it's ok. It's also the only valid certificate in MMC->Certificates->Personal.Furthermore, also using other smartcard (etokens) of other users it doesn't work.
Cisco WAN :: 877 Default Route Using Track Command?
Jun 5, 2013I have an 877 router which has a DSL WAN interface. The DSL service at this site is unreliable, so the company have purchased a separate 3G router to be used as a backup. This device maintains 3G connectivity at all times and has a static IP on the internal subnet (for arguments sake let's say 10.0.0.253).
What I want to do with the Cisco router is to track the DSL interface and if it is up, install a default route pointing to it. If it is down, I want the default route to be the 3G router.
I am thinking the best way to do this is to set up a track and then set 2 default routes; one which is installed if the tracking is up, the other has a higher admin distance and points to the 3G router and thus should only be used if the track is down. For example:
track 10 interface Dialer0 ip routing
delay down 30 up 30
ip route 0.0.0.0 0.0.0.0 Dialer0 track 10
ip route 0.0.0.0 0.0.0.0 10.0.0.253 100
Is this likely to work or is there a better way to do it?
Cisco Switching/Routing :: Route-map Command Support On Switch 3550?
Sep 30, 2012I have cisco switch 3550 IOS Version 12.1(19)EA1c.
I can configure route-map commands on that. but i can not apply that into any vlan interface. while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.
Cisco Switching/Routing :: Catalyst 3560 - Routing Enabled With / Without Default Gateway Or IP Route Command
Feb 25, 2013We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
Broadband :: Windows 7 No DOS Command To Fix Network?
Feb 27, 2011windows 7 won''t go into DOS commands and having problems with network. Often does not get a Local Area Connection, no IP Config, DNS Server Config not responding
View 2 Replies View RelatedCisco VPN :: 891 Nat IP Can't Ping VPN Configuration Professional
Sep 26, 2012I configured a VPN site to site through an Cisco 891 and Lynksys RV042: Followed this steps: [code]The VPN works only for computers without NAT. [code]
View 4 Replies View RelatedCisco :: 881 - ICMP Using Configuration Professional?
Sep 5, 2012I am trying to set up the router (881) using Cisco Configuration Professional, to allow ping reply's..I can not for the life of me figure it out.
View 4 Replies View RelatedWireless :: Linux Command Iwconfig For Windows XP?
Apr 26, 2011Hoy-hoyIs there exist any tool like iwconfig (linux tool, I think), but working in windows XP?civ-civ
View 3 Replies View RelatedUploading FTP / Slow Speeds Via Windows Command
Nov 7, 2011First this is my setup, i have a 100x100 mb fiber pipe at a location i am working at. i am comming out of a cisco fiber router to ethernet. i am coming straight from the fiber switch to the computer at a 1gb connection. So my problem is when i try to upload to my ftp server via windows explorer i can never get about 1.5mb, but if i upload via command prompt it goes at about 60mb upload, so the pipe is good. So you say why dont you just use the command prompt, well i have specialized gear here that run xp emmbedded and it does this via the windows explorer. I have tried 4 other computers and they all do the same thing. I tried a UDP video stream and worked at over 10mb stream. but all the ftp uploads cap out at 1.5mb.
View 3 Replies View RelatedWindows Xp - Command Prompt Appears And Disappears?
May 19, 2012Windows XP sp3 home edition.On login in when the PC open the desk top the icon opens and a command prompt flash and desappears
View 1 Replies View RelatedHow To Route Public Ip In A Windows Server With Two Nics
Feb 20, 2012i have a windows 2003 server using it as a proxy server with 2 nics. 192.xxx.xxx.xxx to the LAN and 172.xxx.xxx.xxx to the internet router. although I can browse on the LAN, i cannot ping any public ip. because of that i cannot use my outlook to get my mail.
View 1 Replies View RelatedCisco Firewall :: Using Configuration Professional For 891 Router?
Aug 5, 2012For the moment we have a router Lynksys RV042 , and we want to change it with an Router Cisco 891 .I have configured our new router Cisco 891 using Cisco configuration Professional because I am not an cisco expert:
I have configured : DHCP, DNS, NAT, Firewall (I have selected : Advanced , Low Security) . I have tested the new router and :
- Internet is working
- We can send Emails, Receive Emails from Outlook
- Our Web sites cand be accessed from the outside .
- File Share is working
We have 2 problems
1. Can't Access from inside the network : our public ips configured in the NAT : **.***.**.150 .
When we try : ping **.***.**.150 , we receive : Request Timed Out .When we try ping 192.168.1.2 , everything it's ok.When we try ping from outside of the network , everything it's ok.
PS : I want to mention that : if I put back the old router I can access our public IPs.
2. When I send Emails to yahoo and access View Full Header I receive : dkim=temperror (key retrieval failed)
------------------------------------------------------------------
Received-SPF: pass (domain of ********.com
designates **.***.**.150 as permitted sender)
Authentication-Results: mta1036.mail.ac4.yahoo.com from=********.com; domainkeys=pass (ok); from=********.com; dkim=temperror (key retrieval failed)
Received: from 127.0.0.1 (EHLO mail.********.com ) (**.***.**.150)
[code]....
I think our Email Server (Smarter Email) is using the ip Adress: 127.0.0.1 (Please look in the attachement) and this ip is restricted from the firewall (ccp in zone to out zone : Drop : 127.0.0.0/0.255.255.255) (generated by Advanced firewall > Low Security) .How can I set that to work ? Can I delete that row ?
2 Nics In Windows 7 - Deleted Route Automatically Reappears
Jun 30, 2011I have 2 NICs in my Windows 7 PC at work.NIC #1 connects to our private network and is also how I connect to the internet. NIC #2 connects to our customer's network and does not allow internet connectivity for me.When I first boot up my Windows 7 machine I get the following info in route print:Despite the fact that I have a persistent route with metric 1 to send my internet traffic to the 172 subnet, the internet requests go to the 10 subnet. I am guessing that is because the non-persistent route to the 10 subnet has a metric of 20 vs. the 21 for the 172 subnet. I delete the route 0.0.0.0 mask 0.0.0.0 10.242.1.254 and I am able to connect to the internet again.HOWEVER, after something like 4-6 hours, (without rebooting) the bad route automatically reappears in my route table! I become aware of it because I suddenly have connectivity problems. There are no entries in the Windows Logs that seem to be related (i.e., no DHCP renewal requests.) so I do not know how or why it reappears.
View 1 Replies View RelatedCisco WAN :: 5510 VPN Traffic Will Not Route For Windows Vpn Client
Jul 31, 2012I have an ASa 5510 and setup remote dial in users.
I wanted to use the windows 7 built in client and also the draytek site to site VPN options however when they connect VPN traffic will not work however when i use the cisco VPN client then everything works fine.
All the VPN's connect pretty quickly.In the syslog I a getting errors when i try and ping something: [code]
Dell Inspiron 4010 With Windows 7 Ultimate - Run Command To Switch On Bluetooth
Aug 26, 2011I am using Dell Inspiron 4010 with Win7 Ultimate installed in it. what is run command to switch on the bluetooth?
View 1 Replies View RelatedCisco Firewall :: 5510 Trace-route / Antispoofing On Not Default Route
Jun 24, 2011I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
What Is The Command Switch
May 28, 2012What is the command switch (the letter/s that you use withsign after the command) that can be used for displaying the per protocol statistics with the above command
View 1 Replies View RelatedCisco :: Run The Int Range Command
Oct 1, 2012I am trying to run the int range command and i am getting this error
View 19 Replies View RelatedIP Configuration Command Won't Show WAN IP
Apr 16, 2011i have ADSL. modem:Meganet when i connect to internet from windows xp with making PPPOE connection everything is fine and when i do ipconfig i can see my IP. but when i connect directly from router then IPconfig show this only:
[code]...
Find Out A Computer Name Through Command?
Feb 15, 2011I have a laptop running XP that has system 32 errors. i have run check disc and i now it tells me there is errors that can not be fixed. this laptop is aprt of a domain and i need to find out the computer name. what command if any can i use to find out the computer name?
View 2 Replies View RelatedConnecting To Another PC Via Command Line?
Apr 14, 2011My grandma has a PC with Windows XP, she uses it only for Skype calls. can go in to her PC using command line from my PC? What commands should I use and what modifications to do on my grandma's PC? Should I ask permission from grandma's ISP (which is the same as mine)?
View 3 Replies View RelatedWhat Does 192.168.1.1 Domain Mean In Netstat Command
Sep 28, 2011I was using command prompt and typed in netstat -a to see opened ports on my XP computer. Then I found a weird result I have never seen it before.
It was Proto local address Foreign address state
TCP myXP computernameort# 192.168.1.1:domain Fin_Wait_2
What does this 192.168.1.1:domain mean? I believe 192.168.1.1 is my gateway router, but why it says :domain? few minutes later, I typed netstat -a in the command prompt to check it again, but it wasn't there anymore. does this mean my computer is on a domain network or something? As far as I checked, my computer doesn't seem to be on a domain network, but I just don't know what it means.
Cisco WAN :: What Is The Equivalent Command On IOS-XR 4.3.0
Jan 10, 2013I want to configure this:
ip vrf TEST
rd 65500:1
route-target export 65500:1
route-target import 65500:1
bgp next-hop Loopback500
on IOS-XR 4.3.0
What is the equivalent command on IOS-XR?
route-policy TEST1
set next-hop 1.1.1.1
vrf TEST
address-family ipv4 unicast
import route-policy TEST1