Router Near Appliances Not Giving Good Response
Aug 22, 2012
I have ZyXEL PLA4201KIT Mini Powerline Ethernet Adapter Starter Kit Up to 500Mbps to connect my desktop to the internet and recently i've been getting random moments where i lose internet connection so everything stops working. I have to either restart my comp or take out the ethernet cord and put it back in. my router is next to our tv and i read somewhere that having it next to a big appliance will suck all the power for itself.
View 1 Replies
ADVERTISEMENT
Apr 7, 2012
Buying a TP-Link W8961ND modem/router. Didn't work at all, except for a vague sense I got that the internet wasn't spending as long 'down' as previously when it did drop.And now today my housemate and I are both connected and suffering these intermittent drops, which become more and more frequent, until finally the internet cuts out and won't return. Now I cannot get the TP-Link router to connect to the internet at all. However, switching back over to the original D-Link router now the internet DOES work, but still only intermittently. As I've been writing this it's dropped out for a couple of moments twice!
View 10 Replies
View Related
Apr 6, 2012
I have a brand new 2911 router out of the box. I attached a terminal to the console port and watched the bootup sequence. I get the "press return to get started" at the end but I can't get any response. I just used the same cable and terminal on a 3750 switch and an ASA. What am I missing?
View 3 Replies
View Related
Dec 27, 2012
We are using Cisco ACS server Version : 5.3.0.40.6. Our tacacs appliances are crashing on AD authentication on a fairly regular basis. I have been searching Cisco.com to see whether we are on the latest version or not however I couldn't find anything lattest than what we are currently using. Are we on the latest version?
View 1 Replies
View Related
Aug 15, 2012
MY voice conversation on magic jack breaks up when I download a movie to my direct TV. I have a Belkin F9K1103V1, N750Db. I'm not using WiFi, Im wired to ports on back of Belkin.
View 3 Replies
View Related
Apr 3, 2012
A thunderstorm about 3 hours ago fried my DIR-655 rev. A3 router. I heard a zapping noise and that was it. All the signals are messed up, even after a hardware reset, and the router runs extermely hot, with lots intermittently blinking and no connections.
I need another router with similar features, especially with a USB port for my printer.I found the DIR-655 reliable a long as it lasted, but I never upgraded the firmware, which was fine with me. Nonetheless I want to buy a more modern solution.
Talking to tech support at D-Link the DIR-825 was recommended. Is the DIR-825 router a good router for my needs ? Is it a worhty upgrade to the DIR-655 router ? Does Shareport work well with it ?
View 1 Replies
View Related
Mar 20, 2013
I have the following LAN setup: I am trying to ping the Wireless Access point (10.60.1.1) from the Cisco Router (172.16.88.21) but I am not getting responces. I can however ping 10.60.1.1 from server (172.16.88.36). Tracert from the server shows that it is going through the Rotuer and Firewall.
View 8 Replies
View Related
Nov 6, 2011
I heard there was this router that does not make other user slow their internet even if there are multiple users.
View 5 Replies
View Related
Mar 29, 2012
I've updated latest firmware & installed 5 pieces of WRT54GH at our building. Then I noticed each of them disappear from wireless connections list and IP scan list (no ping response). If they might not response to pings but they serve as switch without any problem, I mean there are no wired connection problems, they work as switch all the time. The problems are -again-
1-) Wireless lost and / or 2-) Ping response lost
Turning them off and on again will fix them. But I'm tired of bosses who complain about their faulty pc connectivity.
Don't they run 7/24? I tried to restart them on every 12 hours programmatically/remotely but it couldn't work.
View 1 Replies
View Related
Mar 9, 2011
Is this router good for gaming with the Xbox 360 & PS3.My linksys wrt120 n is giving me fits I need a better gaming router.
View 2 Replies
View Related
Dec 29, 2012
How to know the serial 0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 12 Replies
View Related
Jan 16, 2012
I'm in the market for a wireless router/AP. It must have gigabit LAN and would like it to have 300mbps wireless rates. I've been looking at the Linksys E3000 but I'm a little hesitant because of some of the reviews about this thing getting hot. Heck, even reading thru threads on here, it seems like there's mixed reviews on most everything!
View 9 Replies
View Related
Dec 11, 2012
Windows association failed because Windows did not receive any response from the wireless router or access point. This is the message I have just got out of the blue from my laptop. it is showing that there is excellent strength... And I am also on my iPad connected to this connection.
View 1 Replies
View Related
Aug 31, 2009
I have a brand-new WRT160N router (just installed FW v3.0.02) that I am using in mixed mode, 20MHz only, Channel 11, not filtering anonymous requests, beacon at 2306, RTS at 2307, fragmentation at 2346, MTU at 1400.
These settings bring the response from a simple ping command over the wireless network down to approximately 6ms on average, which is good. However, when I still noticed inconsistency with my internet response over wireless, I decided to do a test.
By simply running the "ping" command on 192.168.1.1 (the router address) over the wireless network repeatedly (approx 3 seconds between commands), I can see that approximately every 65 seconds or so, router response time increases to over 100ms for a few seconds, then decreases down to 6 ms or so for another 65-70 seconds. See the chart below. The interval looks pretty consistent to me, with the exception of one stretch where it goes for over two minutes without a spike. I see this pattern regardless of what else I'm doing over the network. I do not see this behavior running the same test when physically wired to the router (ping response time is a flat line at 0ms).
View 4 Replies
View Related
Jul 13, 2008
I need to remotely monitor a WRT45G from a remote host on the Internet. As such, I want to allow ICMP ping replies on the public Internet interface. However, I have found no feature to allow me to do this. Similar Netgear devices do allow this feature. I suspect the answer is, "you can't do that".
View 2 Replies
View Related
Jan 27, 2011
I'm having trouble connecting using this new card i bought. i have installed the latest drivers and i can find networks and the signal strength is good too but when trying to connect after ive entered the passkey i get the message " no network found" or "did not receive response from router" or something along those lines. i can connect with my older card which is a wmp54g but that one shows less signal strength and my connection breaks from time to time (hence the upgrade to wmp600n) on a sidenote, my wmp600n card works perfectly fine under linux but i want it to run in windows (mainly for gaming) Im running windows vista 64 bit and the wmp600n has the latest drivers installed.
View 3 Replies
View Related
Feb 21, 2011
I have a Dlink DIR 615 , I can never get it to manage the time correctly, even without any down time the time always goes off by hours or days. I tried using an NTP server option... 3.ca.pool.ntp.org but it doesn't work.... so I am not able to schedule the internet effectively router that they have that keeps the time and allows them to control the Internet access that would be good. My kids are teenagers so sometimes it is like talking to a wall trying to get them to control their internet, I can easily block them entirely as I have Mac filtering set, and I will do this, but I would like to not have to constantly check to see if they are online which is easily done with Ipods.
View 11 Replies
View Related
Oct 21, 2012
I switched to xfinity and I really don't feel like renting their gateway for $7 dollars a month. Gateways are crap anyways. So do any of you know of a good router and modem that can be paired up to work well with xfinity and has good speed?
View 1 Replies
View Related
Dec 19, 2011
Range is not good for my E2500 router. My house is on one level and spread out quite a bit. Have the router near my main computer. If I take my laptop or Iphone into my bedroom (about 70 feet away-thru 3 interior walls), I have no wi-fi. If I put the router in the middle of the attic
View 4 Replies
View Related
Nov 9, 2012
Each time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies
View Related
Jun 23, 2011
I replaced my old wireless router with a Cisco Linksys E4200, running firmware version 1.0.02 build 13 May 24, 2011. About once a minute the router sends an unsolicited DNS message to the IPV4 multicast address 01:00:5e:00:00:fb with a destination IP address of 224.0.0.251. The unsolicited message is a DNS response with source port 32784, transaction ID 0, flags 0x8400 (standard query response, no error), questions 0, answer RRs 2, authority RRs 0 and additional RRs 1. The two answers both relate to the router itself: one has Name Cisco18738.local, type A (host address), class 1 (IN), cache flush true, time to live 1 minute, data length 4, and the address of the router. The other is the reverse of the same address. The additional record is for Cisco18738.local, type NSEC, class IN, cache flush true, time to live 1 minute, data length 5, next domain name Cisco18738.local, RR type A (host address).
When my desktop computer receives these messages it logs an error, for example: "Jun 23 07:39:22 sauterws02 avahi-daemon[1067]: Received response from host 10.146.9.1 with invalid source port 32784 on interface 'eth0.0'" The 10.146.9.1 is the router's IP address. I also see these messages on the wireless link from my laptop.I suppose the E4200 is generating these DNS messages in a misguided attempt to make sure there is no old information about its name. Is there a way to turn them off? If not, is there a way to report this to Cisco as a bug?
View 9 Replies
View Related
Nov 9, 2011
I am trying to recover a WRT54GS v1 router from a bad flash. The power light is blinking and would not accept pings. Since I figured it was already hopeless, I attempted shorting pin 15 and 16 which cause it to start receiveing pings. My problem is it won't accept the tftp flash, I've tried both cmd prompt and auto upgrade utility. Upgrade utility says "Unable to get response from the server" however it is still accepting pings. Cmd prompt TFTP says it can't read from local file. I am using windows XP. Code...
View 3 Replies
View Related
Oct 1, 2011
How Do I give the Static IP Address given to the router by the ISP to machine
View 1 Replies
View Related
Mar 9, 2012
I have just upgraded my internet connection. My ISP is now supplying 50mpbs. If I connect my laptop or pc directly into the ISP modem I get a speed of 75mpbs, very happy with that. But if I connect my Sitecom wl-340 router to the ISP modem and then my pc or laptop into the router i can only get 10mpbs! I have connected everything with cat 5 ftp cable.
View 1 Replies
View Related
May 13, 2013
Region : Germany
Model : TL-MR3020
Hardware Version : V1
when visiting Switzerland and Italy with my German SIM card I noticed that roaming is not working very good with the TL-MR3020. The reason is that the internet provider needs to be set in the config, in my case to o2 Germany.When I travel with this SIM card to another country, I roam into other networks.As I cannot what provider is currently active (as o2 has contracts with almost every provider outside Germany) and even if I could see it I have to adjust the settings in the config if anything changes, the satisfaction effect on this trip was not very good.
Also I noticed that sometimes (only sometimes) the setting resetted itself to o2 Germany when unplugging the device, this added some extra negative satisfaction to everything.In my understanding the router should have an auto detection for the currently active network and auto setup for the dialin parameters and everything else. Like every smartphone on the planet. Maybe you can also add a setting where you can enable or disable data roaming to save people money if they do not have a international data option booked.
View 2 Replies
View Related
Sep 12, 2012
A friend has 2 Asus RT-N66U's for the purpose of extending wifi range from her small companies shop to her house which is next door from each other.
from the house I can connect to the first router via wifi with a decent signal strength but what I need to do is backhaul from the other router via wifi and then have another wifi network in the house.
can this be done with just the 2 routers, or should I be looking for a cheap point to point setup and 2 separate routers?
View 1 Replies
View Related
Jun 21, 2011
i have a cisco router that has dhcp configured, the router ip address is 10.10.10.***. all computer that attached to the router are using static ip and works fine but when i am connecting my laptop using wireless in gets an 192.168.1.*** address.
View 17 Replies
View Related
Feb 18, 2011
My connection is good directly to the modem. But the wireless router is giving off very slow speeds. For instance the modem is 10Mbps but I'm only getting 1.5 - 2Mbps through wireless.
View 4 Replies
View Related
Mar 4, 2011
I have a switch connected from the internet outtake in my apartment.This switch gives internet to two, or sometimes three computers, by cable.To get wireless I have a DLINK-615 connected after the switch.This solution works flawless for some time, just after the router is started or reset. If I go to speedtest.net both the upload and the download works flawless.However, after around half an hour it's virtually impossible to upload, which gives heavy lag in programs like skype and games. If you try to speedtest.net now the download is still fine, but the upload gives a result of 0.1mb/sec after trying to even start the test for 3-4 minutes.Router giving up upload completely
I've tried to change the IP in the router to prevent a conflict between it and the switch. The problem is still there whatever IP I choose though, I simply have no upload.I've also tried to disable the DHCP, mess with the MTU and to enable the Access Point mode with no result.
View 2 Replies
View Related
Jan 5, 2013
I have 2 public ip, 1.1.1.1 anda 1.1.1.2. I'm connected to the ISP using PPPoE. I also have a router and a firewall. I want to assign 1.1.1.1 to router and 1.1.1.2 to the firewall. I do not want to NAT 2 times (one in router and one in firewall)That's why i want to bridge Fa0/0 and Fa0/1.Could this be done in Cisco router? I've done this command but it's not working as i want. I'm using bridge irb and bridge-group.
View 6 Replies
View Related
Oct 5, 2011
I was using my internet on my Acer Windows 7 operating system wireless just fine on Monday. I tried to use it on Tuesday and could not connect to the internet wireless any longer. I get an error message next to my network stating ""The settings [COLOR=green ! important][COLOR=green ! important]saved[/COLOR][/COLOR] on this computer do not match the requirements of the network"I have never encotured this kind of problem before. I proceeded to call Comcast who did all kinds of trivial beginner troubleshooting such as restart the router, restart the modem turn on and off the computer.
View 3 Replies
View Related
Apr 25, 2013
I have VPN Router (3845) in Head Office and VPN Router (1921) at Branch Office. I have also internet router (1921) which passes through ASA 5520 to internal Network at Head Office. I can give internet connectivity to Head Office Users by giving access in ASA 5520 with following lines: nat (inside) 1 192.168.2.13 255.255.255.255.
I have added line for internet access for Branch Users in following manner in ASA 5520: nat (inside) 1 173.16.33.4 255.255.255.255. My Head Office user can access internet but my branch office user cant access internet. how can i give internet access to my branch office users?
View 1 Replies
View Related
Apr 5, 2010
I setup a WRT120N router in my home. I am having a issue getting good coverage over my single floor ranch style home. Would changing the Standard Channel (currently set 6) make a difference?
View 9 Replies
View Related
