My company recently purchased a custom domain name through In Motion Hosting (inmotionhosting.com) which has worked great up until today. As of this morning we are not able to view our webpage online (ronnysinc.com) or any inmotionhosting pages including our email accounts. However, we can view any other website and computers outside of our network seem to be able to view those pages without any problem. [code] As you can see it works fine with any other website such as google. My initial thought was it was being blocked by our firewall but when I log into the router I do not see any firewall settings that would create this block. I also tried resetting the router and flushing the DNS with no success.
I have two ACS 5.2 running as primary and secondary instances respectively. When I try to delete a remote log target under System Administration > ... > Configuration > Log Configuration > Remote Log Targets I get the following error message...."The item you trying to delete is referenced by other items. You must remove all references to this item before it can be deleted".
I have searched the configuration within the web gui and was unable to find anything that reference the object that I'm trying to delete.
My laptop is connected to a router via wifi but it keeps getting a DNS fault. I have another PC linked to the same router via WiFi and that works perfectly all the time. I have the same problem on both google chrome and IE browsers where I just get the message telling me that the DNS look up failed. My internet is still connected as I can dial into my remote CCTV cameras and I can ping website ip addresses. Most times I can just turn off my wireless adapter and turn it back on and it works for another hour or so. But sometimes it wont work all day, unless I start my laptop in safe mode, when it works everytime! I have flushed the DNS cache several times but to no avail.
I am running a webserver locally and I am unable to resolve it by domain name (e.g. mydomain.com) when I am inside my network. However, I am able to hit it internally (e.g. 192.168.0.10) just fine. When I try to access mydomain.com from inside my network it comes up with my Actiontec router's admin page on 192.168.1.1.Here is my configuration:Actiontec FIOS router 192.168.1.1 (connected to internet)DHCP disabled Netgear Router 192.168.1.2 is in the DMZHas cable running from Actiontec's LAN port to Netgear's WAN port[CODE]
I have been trying to connect to the Internet via a wireless connection but keep receiving the above error. None of the Windows solutions resolve the problem. On Google Chrome I see a screen saying 'This web page is not available', and receive 'Error 105: Unable to resolve the server's DNS address'. I cannot access Internet Explorer either.The strange this is that this problem only seems to occur with some wireless networks, as I can connect fine at home. In certain places, however, I am told that I am connected but that accss is 'Local Only', and I cannot open any browsers. I need the problem resolved as soon as possible as I cannot access the internet where I need it most.
I am using the Cisco VPN Client 5.0.06.0160 - and am having an issue connecting to my ASA 5510 via VPN. This issue is happening on 1 of our laptops. All other laptops connect just fine. So the problem is not in the ASA. I have double checked the client setup and config and it too is correct. The interesting thing is, we are connecting to an IP Address and not a host name.
I'm connected through the router, a few times a day I cannot open web pages, getting error: Error 105 (net::ERR_NAME_NOT_RESOLVED): Unable to resolve the server's DNS address.Skype continues to work. Here are the results of pinging:
Quote:
Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:UsersSri Guru>ipconfig /all[code]....
One technician said that this is the providers problem, but I don't think so. When I restart the modem everything works.I have a Netgear WGR614 v9 router.I use ESET 5 security. Btw, connection drops on all computers connected through the router, so it's not my firewall.
I have a Cisco 1721 router with an ADSL wic. I have followed guides on the Cisco website so that I can connect the router to my home adsl connection. The router connects to my broadband provider and sucesfully obtains an IP address along with Dynamically assigned DNS servers. I am able to ping google.co.uk from the router but not from clients attached via DHCP.
I have noticed that if I ping the IP address of google.co.uk from a client it resolves but it will not resolve the name. This would lead me to believe that the problem lies with DNS resolution/forwarding but I do not know how to investigate further.
I am working on adding a mapping to our external address for our mail server - let's call it mail.example.com
I would like to be able to access mail.example.com internally for our user's smartphones - if they access our company WiFi they are not able to get mail using the mail.example.com as the server name in their phone setups. However, once they leave the office and use any other WiFi it works fine. Also, I am unable to ping that address from any internal device. I believe also this is the reason Exchange accounts do not work on our site to site VPN connections.
I have a ASA 5520 and work primarily in the ASDM 6.4 to do configurations in the main office and have 5510 in our site to site connections.
We have many CT/MRI etc. machines and Servers in the Hospital LAN. Now intermittently we are loosing the LAN connectivity i.e we are not able to ping any system from any node inside the hospital network for sometimes, after some time it will start working and then again it will stops again.We are using procurve switches and also we are not using any router
I have strange problem I am using my static ip system since two year, I dont have issues so far, since two days I am facing a strange issue when I am piging my system I could able to see reply,
but when I am trying to connect via MSTSC..blank screen even I am unable to get login screen also...
I have tried to connect to log mein and team viewer all are having the blank screens
i'm trying to hook up mi lorex 4 edge+ dvr to my lcd tv (not. full hdtv) i tried using the hdmi cable and adapter but it gave me a message "system not recognized" i would like to know if there is something else i could try. tv daes not have vga connection.
Why can't I connect to the website for Target Stores? Each time I try to connect to Target Store website the small box fills up at the bottom of the screen, then the hour glass appears and Windows Internet Explorer says "program not responding". No other websites give me this problem, only Target
I was attempting to troubleshoot a logon problem with some machines, when it was finally revealed that there was a managed switch between the host and the target preventing this.
How would I detect this in the future? (A tracert showed nothing between host and target.) Would Wireshark show me this info, with reduced TTLs?
getting a picture of all devices between a host and a target?
128 compact flash got corrupted and suddenly not working after i reboot the 2801 router. now i have a new 256 compact flash and 512 compact flash but i cannot still to boot the 2801 properly. it always do looping like booting in rommon and will be the image decompress but in the end theres an error, Wrong system software for this hardware. ive tried different ios but still the same.
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 262144 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabled
I have a multiple Offices in my location , all my external users are connecting my site using Cisco Client to site VPN and accessing my 2 sites , All users are able to access my 2nd office servers which are in 10.10.0.x pool , I have a different vlan in that same location with 10.10.35.x series and users are not able to access this pool servers , I am not much familiar with Routing . i am using ASA 5520 firewall .
i have two servers that is Primary domain Controller and File Server. When i remove the client computer from the domain and try to rejoin the domain again it refuses, when i ping it replies. i can not assess files in the file server It prompt"Logon Failure: the target account name is incorrect" Suprisingly When i logon in other clients its OK. but some clients give ths said error though the communication with the server is fine
I am using an ASA 5520 running 8.2(4). My objective is to get a VPN client to access more than one network on the inside of the network, i.e., I need to VPN in with an IPSec client and be able to establish tcp connections to servers at 192.168.210.x and 10.21.9.x and 10.21.3.x, I believe I am close to having this resolved, but seem to have a routing issue.
I would like to limit the bandwidth available to a different target machine. I have been trying to do this on a Cisco 3750, but first I came across this message:
% QoS: policy-map with police action at parent level not supported ...
Then this:
% QoS: policy-map child ... ClassMap BackLimit only support MATCH-INPUT INTERFACE
Is there any documentation, I searched the forum but all I see are complex solutions, I just wanted to limit the bandwidth for a machine that is in a different site. I wanted to apply the policy on an interface SVI.
Today when we run one applcation to access a target server with IP address 10.2.2.13, the application cannot run through and appearing error message related networking.The target server has two network ports whereby another one with IP 10.2.2.14 is running OK with the same application. All these two connections are connected to the same Cisco switch 3750, after the switch then go to Cisco ASA firewall which has no access control rule for this 10.2.2.13 and its subnet, and then the firewall connect directly to the application server.We can ping, remote desktop access and telent port for the application to the target server by using 10.2.2.13.We swapped the cable connection of the ports from one another and try the application again, the IP with 10.2.2.13 is still fail and IP with 10.2.2.14 is OK.We then change the IP from 10.2.2.13 to 10.2.2.12 or 10.2.2.155, all are OK. We changed back to 10.2.2.13, it is failed again.The switch is in running real time production and so we cannot power cycle or reload the switch.
I'm configuring a console server for configuring remote devices. This is working well except for the fact that if a target device is in ROMMON mode, the console server refuses to displays the target device console. It does open the connection but the ROMMON prompt is not shown on the console server . This is essential for this device as we will need to use it to reset passwords remotely and thus need to be able to access ROMMON mode from the console server.
Parts used are a 2951 router and a HWIC-8A serial card. Posted my config below:
I have and 880 W router. The LAN members can get out t o the internet. Now I want to configure NAT such that outside computers can access a couple of the machines using Remote Desktop (RDP). I am using Configuration Professional.
When I configure inside to outside, the remote computers can't connect to the target machines.When I configure outside to inside, the target machines acn't get to the internet.
When I try to use the advanced NAT definition wizard, I can't complete the task because the only inside pool (?) or LAN (?) is "designated" and not available to select. I can't free it up without deleting the one working NAT entry which is the one that enables all computers to reach the internet.
where the host names do not properly resolve with the right ip address.Example, I ping a host name, it gives me an IP, but when I VNC into the workstation, it is a totally different host.
1. I have a DSL modem + wireless + router 2. I have a Vonage phone that taps into one of the LAN ports 3. I have DIR 655 router that taps into one of the LAN ports 4. I have NAS that taps into one of the DIR 655 LAN ports 5. I have Printer that taps into one of the DIR 655 LAN ports 6. I have a BD Player that connects to DIR 655 through wireless.
All my components that are tied to DIR-655 resolve through IP address. I would like to have the resolution through host name as it works with my first router (DSL Modem / Router). Identifying components with IP address is not only inconvinient in terms of reading / recognizing my components but ther could be other issues. I am not very techie on the networking side but I do have some basic knowledge.
I have a fixed external ip address.I have port forwarding setup for accessing a NAS inside my LAN, lets say port 12345.Now when I use my laptop outside my own LAN, e.g. 99.99.99.99:12345 resolves nicely to my NAS. But when I use the same 99.99.99.99:12345 inside my LAN, it does not resolve. Instead, it gives me a 'server takes too long to answer' error
I have also setup a virtual host to an ip cam inside my network. That one resolves just fine. I tried enabling remote management on the DIR-655 and also that works fine using 99.99.99.99:8888.When I replace the external ip address with the internal ip address of my NAS, thus bypassing port forwarding, it obviously also works ok.
Why the forwarded ports are not accessible when I use my own external fixed IP address? Does the DIR-655 treat it different than other external IP addresses?
I have a 5505 that currently has inside/outside interfaces and everything is working just fine. I am trying to create a DMZ that will essentially be just for vendors/guests. the DMZ will have full access to the outside (Internet) but no access to the inside. I am using the FW for DHCP, and 8.8.8.8 and 4.2.2.2 for DNS. I currently have 1 laptop in the DMZ vlan, and it is getting a correct IP, and it is showing 8.8.8.8 and 4.2.2.2 in ipconfig. I can ping/tracert 8.8.8.8/ 4.2. 2.2/74.125.137.147(what url... resolved to on a laptop connected to the inside vlan), but I cannot ping nor browse to url.... [code]
As far as I understand it Fault Manager need to be able to do reverse lookup for ip adresses to show the correct name in the "device name" column. I have double and tripple checked and all devices that only is shown as an ip address do have a reverse in the dns used by the LMS server. The device is correctly registered and inventory have been run. If I hold the mouse pointer over the crosshair on the row of the offending device all info is shown including correct device name and fqdn.
The server is upgraded from 4.2.1 to 4.2.2 and we have the same problem before the upgrade.
I am unfortately the only IT staff now for 100 - 150 users in my organization besides a consultant who doesn't have an answer for this issue even though he sold us the hardware and environment. While I realize that this version of the Cisco VPN doesn't support Windows 7, we do have some Windows 7 PC's that have the software and work perfectly fine upon install. In this case, I am at a remote location with both a Windows XP SP3 and Windows 7 SP1 computer. Both have the same Cisco client installed and connect to our ASA5520. I cannot get DNS resolution out of this computer to any remote network resources or other domains such as cnn.com including localhost. Adding the entries manually in the hosts file does nothing and I even tried removing the VPN client, the network connections and components and even a manual winsock reset. I cannot resolve internet DNS but can ping all internal IP addresses. The Windows XP computer across from me has no issues. I am not going to update any VPN clients as we still don't have computers who are functional so I need to spend money where it counts before I upgrade computers and I cannot perform a downgrade on this model because the previous person who bought it didn't bother to check Windows XP compatibility before they installed them in 10+ communities.
Here's my IP config - FYI all works well when not connected to the VPN for general web domains.
C:UsersAdministrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : GHN-Green-S01 Primary Dns Suffix . . . . . . . :
My Belkin router has an option to set a local domain name, which, I suspect, allows me to address hosts within my own network using this domain. By default, this is set to be "Belkin". Is it possible to call hosts within my network like this, e.g. ping foobar.Belkin instead of ping 192.168.2.4? The thing is, my routers internal page shows all set host names (so dh client seems to work) and the router itself is reachable as router.Belkin, but no other hosts are. My problem here is that the router knows each hosts name, but the hosts don't know each others name. How can I fix that?
Note: Nmap showed that port udp/53 for DNS is open on my router, but I can't find any way to configure it on the Web-interface.
I am setting up a webserver to host our website on our local network. When I'm browsing from an external network, I can pull our website example.com and a sub domain test.example.com. However, when I'm browsing from our internal network, I cannot pull up test.example.com. I am not sure if this is due to propigation issues or what.When I do nslookup from external, it shows my network's main IP address. When I do it from local, it can't find an address and says non-existent domain.Should I have any problems connecting to my website if it is using my external IP address? Will this be a loopback problem? If so, how can I resolve this?
