Unable To Use Wireless Router With 3g Wireless Internet Modem
Jun 1, 2011
I have a Sierra Wireless 306 3g Modem, connected with Bigpond. It is working when plugged directly into the computer via USB.I had it plugged into a Netcomm router, which was Ethernet cable connected to the destop and also our TIVO device.I was able to link o the internet wirelessly from my laptop - though not if someone was using the desktop at the same time. I suspect an IP address conflict was at fault here, though had no clue how to fix that.My actual problem is my Netcom router no longer works and I've had to purchase another. When I plug my router into the computer I get an error message saying there is another computer on this network with the IP address but I tried to change the IP address of the router, to no avail....I returned that router and got another and ended up with the same problem.
View 11 Replies
ADVERTISEMENT
Dec 28, 2012
I reset my Hybrid modem router's settings back to factory settings cause the disconnects were pissing me off.After a while, It disconnected. I tried reconnecting, but now it's only showing "No Internet access."
View 8 Replies
View Related
Feb 9, 2011
So I recently just built a new pc for gaming, I can't seem to connect to the internet through my router or directly through my modem. I have connected directly on my laptop and it works and through router and it works.
View 1 Replies
View Related
Feb 7, 2011
The internet at my parents house has recently gone on the fritz..the wireless router is a N600 Wireless Dual Band Router WNDR3400..The computers of the house are able to connect to it..But it does not allow internet connections..The 3 computers are an HP Laptop running windows 7.a Dell Dimension E521 Running windows 7 & and an older HP Walmart special running XP.They can connect to outside systems and through a wired connection to the Modem from Cable vision. They replaced the wireless router and the problem continues.Internet is capable by plugging directly into the Cable vision router,unfortunately do not have the cables to try through the Netgear router to test that out..
View 3 Replies
View Related
Feb 8, 2011
i have a wireless usb to get internet on my windows vista laptop...and i need to share internet with other computer with my wireless router so how i can do it ?
View 7 Replies
View Related
Jun 14, 2011
I have a just dumped my landline broadband for 3g wireless. I have: a e169 usb stick a siemens speedstream 6520 router (one pc) a wifly-city wifi usb adapoter. (other pc) laptop (built in wifi)
i can file/printer share no worries but can't share the internet connection. I've tried everything I can think of!
I'm using: mobile partner dashboard 16.001.06.01.500 xp 32bit on all systems
tried enabling share this internet connection. tried setting up ad-hoc. Tried manual ip settings.
View 5 Replies
View Related
Dec 9, 2012
I just had to put a new hard drive in my computer and I reinstalled windows xp. I cant get to Internet saying cant detect my modem
View 2 Replies
View Related
Feb 8, 2012
I am using a broadband internet of a provider named BSNL,through a simple modem. Recently I got a Beetel 450BX1 ADSL2 + Router and want to use the wireless capability of the laptop so that I don't have to be glued to my table. The OS I'm using is Windows 7 Ultimate (32 bit) on an HP Compaq 6515b.I configured the modem by following the instructions in the following link url...I believe that's a straightforward method for configuring a router, and that accomplishing this is very simple.I followed the steps, only changed the username and password to that given by BSNL.Then, finally I unplugged the LAN cable and clicked on Connect to <connection name>, punched in the serial key. But it does not connect and says "Windows was unable to connect". Even after using Windows Network Troubleshooter the problem is not solved.
View 4 Replies
View Related
Mar 6, 2012
I have D-Link DVA-G3670B Wireless Router But without the usb Port, a PC running Windows 7 Ultimate, a usb modem that I use to connect to the internet and one Ethernet Cable.
My question is: How can i share the internet from the usb modem to the wireless router so I can connect my other WiFi devices to the internet? The router is Factory settings.
View 5 Replies
View Related
Dec 12, 2011
My main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies
View Related
Mar 24, 2012
I have a problem with a talk talk dsl 2680modem or the connection? Everything worked fine until I did a facory reset on the pc (running xp),when I tried to install the talk talk internet from the cd, everything seemed fine with the wizard but no internet? the phone also has no dial tone? I am 99.9% sure it is not a problem in the area,I think its a setting problem with the setup.
View 1 Replies
View Related
Jun 23, 2012
Trying to connect one computer to the internet using a USB Verizon Pantech modem and at the same time connect to printer wirelessly through a Linksys router. We are able to connect to one or the other and can print when connected to the home network or we can surf when connected to the Pantech. We can connect to both networks at the same time, but when we do we can neither print or surf.. It cannot find the printer and does not access the internet at all. Is it possible to do this without buying additional hardware
View 3 Replies
View Related
Jan 18, 2012
Just purchased a Belkin N600 DB N+ Wireless Router because the wireless on my Actiontec PK5000 really isn't so great. When I hook up the router to my modem and after running the install CD I couldn't get connected to the internet. So I looked at my modem and noticed the light where I had plugged in my router VIA ethernet wasn't lit up like the rest of my ethernet ports even after switching them around.
View 6 Replies
View Related
Jun 28, 2012
My internet modem won't read my E4200 router. How do you reconfigure the settings?
View 2 Replies
View Related
Mar 28, 2012
my router cant receive any internet from my modem. my internet ip when it is connected is 0.0.0.0 . when my modem is directly connected to the computer, it works fine, i can access the internet, but when it's connected on the router, this problem occur. iv'e tried the solution on the e300(something , i have forgot ) but it didnt work for me. my ISP is DSL btw. i have brought my router on the shop and it works fine. i even brought my CPU at the shop and used my router there and it works also just fine. Their ISP is also DSL . So base from these i've concluded that the problem is my modem?
View 8 Replies
View Related
Dec 25, 2011
I am trying to get wireless internet set up again and have run into a big issue. Previous wireless router was also a WRT54G and she had problems. I gave her my old one that I was no longer using, but it was still working with no problems.
The problem that I am having is that we are unable to get internet through the wireless router. We are able to get the desktop connected to the internet when we plug it directly into the DSL modem, but when we plug the wireless modem into the DSL modem and the desktop into the wireless modem, then we don't get any internet connection at all.
I had her do a factory reset on modem so that we were starting fresh. I have also tried unplugging both modems and then pluggin in the DSL and then Wireless modem, with no change. We have the ability to get into wireless settings page, but I'm not sure what in there to change that would make any difference on this one.
I know that this problem isn't actually a wireless problem, but it has to be related to the modem. We haven't even been able to get to the wireless part of the set up and we are already running into problems.
View 7 Replies
View Related
Feb 1, 2011
I have a Wrt160n router and a Motorola sb120 modem (provided by comcast after my original modem got fried by lightning, no I didn't have my router hooked up when that happened), I have been having trouble trying to get the modem to send the internet signal to my router. I have tried mac address clone that was suggested on this forum for someone with a different router but still no internet to my computer, its all hooked up through Ethernet cables, the computer I have it hooked up with a hard line is running windows seven. When I plug the modem straight to the computer it works and I have internet but when I hook up the router between them it has no internet.
View 9 Replies
View Related
Mar 29, 2012
I have an E1550 less than 1 year old. Lately, I have been losing internet on the AT&T modem. I called AT&T but as part of their diagnostics, I have to plug the modem directly into the PC. I have loaded the latest firmware to the E1550.Lose Internet but wireless connectivity to router exists.Internet light on modem is out (modem is connected to router)Unplug modem and leave off plug in, internet light is still out.Unplug router, plug router back in - no internet connection but do have wireless connectivity to router.Take cable from modem to router and plug directly into PC internet light comes on in modem and I have internet from PC.Take cable from PC and plug back into router .I have internet via wireless.What I can't figure out is what could be happening in router that would impact modem internet connection. I have replicated this at least 3 times. Yes, the modem is a bit old, but since plugging it directly into the PC works, I'm thinking it has to be the router and I cannot figure out why unless there's some sort of electrical thing going on in the router.
View 4 Replies
View Related
Feb 7, 2012
I used these instructions to put my Fairpoint westell 7500 modem/router into bridge mode: [URL]. Then I hooked my new e3200 to the westell 7500, but no matter what I tried, I could not get any PCs hooked to the e3200 to be able to get to the internet.so able to get to internet too. My questions are:Is there any downside to doing it this way? (ie, not putting westell in bridge mode).Can this cause any slowness or conflicts? Any reasons why bridge mode may not have worked?
View 4 Replies
View Related
May 8, 2011
I own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
View 2 Replies
View Related
Jan 7, 2012
I have a Westell 2110 wired DSL modem for Frontier (formerly Verizon). It's not a modem that has a web interface, so I can't log into it to change any settings. It also, to my knowledge, has no bridge mode (which is a term I know very little about). I had an old D-Link WBR2310 router, and since I knew the wireless and the phones ran on the same frequency, I bought a new Linksys e1200 router. Unfortunately, when I went through the setup of the router, while I know I have a solid internet connection from the modem (I'm hard wired in as I type), and while I can connect to the router, I am unable to connect to the internet. I took down my IP address, DNS servers, subnet mask, and default gateway, and set up the router to run under a Static IP, which it does phenomenally. Unfortunately, when the ISP (via direct line or my modem) changes the IP address after a few hours, my connection drops and I have to go reset up the connection via a hard wire, taking down the information, etc. Why is this the only way I can set up my connection? What could I be doing that I'm not to get it running DHCP correctly? It worked on my WBR 2310.
View 2 Replies
View Related
May 31, 2011
When installing the DIR-615, router installs, but error msg that there is no internet connection. SmartConnect is plugged into the WAN and I have tried the ethernet cable to the computer in spots 1 & 2. Good connection when SmartConnect modem is connected to computer directly.615's Internet indicator will turn green for a while, usually less than a minute or two, then flashes, then may actually cause the routers status indicator to flash off, then back on. Like a reset.
View 2 Replies
View Related
Mar 23, 2011
Every day for the past week my Internet access goes down. I have a netgear router connected to Comcast modem. I have to reset the modem then the router constantly and it gets irritating. I called comcast and they say reset them. But why should I have to constantly reset.... Sometimes I just ignore it and it comes back up later... what is going on??
View 1 Replies
View Related
Jan 19, 2013
Immediately after a power outage, my internet connection predictably drops after a set period of time or usage. It is either after about 30 min or 5-15 mins of watching Netflix. I have a modem hooked up to a wireless router and use the network on my iPhone, laptop and Roku. Since the problem, I have dropped to just having my laptop connected but this has not worked. The wireless network will disappear after the 5 - 20 mins, the light on the modem and router will show no internet (all other lights are normal). Internet connection will be reestablished if I either unplug both the modem and the router (not just one or the other) OR if I unplug the ethernet line from the modem to the router and plug it directly into my laptop (the internet light on the modem will go from "off" to "on"). Despite internet connection working from transferring from the router to the laptop if I connect it back to the router, the internet lights goes off again (resolves upon unplugging and plugging modem and router back in). The internet has not yet dropped when it is physically plugged into my laptop.
I have tried the following:
-Powercycling (temp fix until it crashes again)
-Plugging into a different outlet (I cannot connect it to a different phone line, only have 1 with DSL. Also, I do not have phone service or cable, just internet via DSL)
-Resetting modem
-Resetting 2 different routers
-Calling ISP, their test of the modem was inconclusive
Again, my wifi does not see my network whenever the internet is dropped or the ethernet cord is unplugged from the modem. The outlets I have it plugged into has some type of electrical issue, two electrical devices have shorted out in the room they are in. I do not think this issue is electrical, everything seems to have constant power (unless the power outage shorted out something in the modem). Below are some details of my modem and router. I will provide any additional info requested. I will gladly buy a new modem but I want to see if it can be fixed first.
My modem: Westell
WireSpeed Dual Connect
Model: A90-210030-04
DSL Statistics
Line State: Up
Modulation: G.DMT-Mode
Data Path: Interleaved
[code].....
Router: Linksys E2000 Internet Connection Type: Automatic Config - DHCP (I tried PPPoE and it never got a valid IP address from my ISP)
View 3 Replies
View Related
Dec 6, 2011
I recently changed my internet connection to DSL from Cable, so now I'm using PPPoE type of connection.
Right now my router is configured as Automatic DHCP with the modem doing the PPPoE connection. All is fine and well.
Since I own a PS3, and Nat Type 3 conection is really bad for my online gaming, I would like to bridge my modem and connect to the internet through my router. That way I can properly forward my ports, use QoS and effectively get a better connection on the PS3.
I was able to successfully bridge the modem, but the PPPoE config on the router isn't able to connect to the internet.
Modem and router have been reinitialized after the configurations were changed. I do have the username and passwords, and they were properly put on the router.
View 1 Replies
View Related
Sep 25, 2012
unable to open 192.168.1.1 in google chrome but can access other net work.
View 1 Replies
View Related
Dec 22, 2012
I followed the directions at least 6 times and I still had no internet connection. Is this because I have Windows 8 and all directions are for windows 7? I finally gave up and hooked back up our 6 year old belkin wi fi router. Had internet access in 1 minute. I bought this wi fi router was because Amazon described it as simple, quick, automatically does the work of hooking it up for you. Takes less than 5 minutes.
View 2 Replies
View Related
Jul 28, 2011
I am trying to setup a DIR-601 wireless router (Hardware Version: A1 Firmware Version : 1.00NA ) with my connection from Astound.I am able to connect to the internet from the cable modem (Motorola SURFboard SB5101) but I am unable to get it to work through the router. All the lights on the router look ok.When I look at the WAN status from the router setup page I see :
WAN
Connection Type : DHCP Client
Cable Status : Connected
Network Status : Disconnected
Connection Up Time : N/A
[code]....
* I noted that the router did not show me the correct time. Is that normal ?I have even copied my laptop's MAC address but it did not work. I restarted the modem and the router a number of times but to no avail.
View 1 Replies
View Related
Apr 13, 2012
I have a Netgear N150 Wireless ADSL2+ Modem Router(DGN1000) which i need to connect for wireless access..My internet connection is a wireless one(antenna connected on roof) connection available to only one computer with an RJ45 LAN.Is it possible for me to connect the router to this LAN cable and get internet on more than one computer at a time?? I have the following information
IP :
Subnet :
Default Gateway :
Primary DNS :
Secondary DNS :
MAC of the Registered Computer :
View 2 Replies
View Related
Dec 2, 2011
I was very happy working with my WRT610N connected to the ethernetport of my previous internet modem. Recently I had to switch to a new modem CISCO EPC3925. Unfortunately this combination does not work anymore. I don't get an internet connection on my WRT610N anymore. I therefore have to connect all computers (LAN and WIFI) to this EPC3925. Especially for the WIFI I'm not fully happy. My IPAD2 sometimes does not want to connect, a problem which never occurred when connecting to WRT610N.
I probably need to change a setting, but where? In the EPC3925 or in WRT610N?
View 4 Replies
View Related
Feb 6, 2012
I'm trying to connect my Xbox 360 to Live by bridging my computer's wireless connection. I've done this before for a friend in a different city and it worked fine, and I felt very proud of myself for doing so. However when I try to connect here, the modem won't assign my Xbox an IP address. I've been into ipconfig/all and tried to manually assign the same IP address to the Xbox but to no avail. Same deal with the alternate MAC address option.
To speed things along here's the readout from my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSamsung>ipconfig/all
[Code].....
View 2 Replies
View Related
Jan 7, 2012
I have a VirginMedia 50Mps wireless router that runs 4 wired connections. These are all working fine and have Internet connection. When the router was installed I could also connect to the internet wirelessly on my Laptop which is running Windows Vista Home Premium. But of late I have been unable to connect to the Internet on the Laptop. When you place the mouse pointer over the Icon in the bottom right hand corner, the following message comes up : Currenlty connected to:Unidentified(virginmediaxxxxxxxx) (where xxxxxxxx is a numeric identifier for the modem). Access: Limited connectivity or sometimes it says Access : Local only.
View 4 Replies
View Related
Jan 19, 2013
I am unable to connect to the internet through my wireless router. However, I can connect using neighbor's wireless connection and other laptops in my home are able to connect to the internet using MY wireless connection. The problem started suddenly, I used to be able to connect, then I had the problem so I rebooted and that resolved the issue temporarily. I tried disabling the wireless adapter card then rebooting, this did not work. I also unchecked the TCP/IPv6.
View 4 Replies
View Related
