I have an exisitng ASA5520 which is already working with remote clients using Cisco vpn client configured using ipsec over tcp, I am now trying to get vpn access for Iphones working and having a problem where once connected the Iphone cannot ping any internal device. The configuration on the Iphone does not allow for Ipsec over tcp and therefore uses udp 500 by default, if i create a new profile from a pc and do not use ipsec over tcp it has the same issue where it establishes a vpn tunnel but cannot ping any internal device as soon as I change the profile to ipsec over tcp it works fine.
I just installed a new ASA 5505 for an office with three internal subnets.* The three networks can each get online fine and ping eachother, but cannot browse to shares on the two internal networks other than their own.* How do I configure the ASA to allow all traffic between these three inside networks?
I need to NAT some subnets to one IP and other subnets to another IP. The range command want work because some of the subnets are out of order.For example subnets 192.168.1.0 - 192.168.7.0 and 192.168.25.0, 192.168.28.0 nat'd to 220.127.116.11. subnet 192.168.26.0-192.168.27.0 nat'd to 18.104.22.168
I have a WRT600N dual band router and have only been able to connect to the 5Ghz when it's network mode was set to mixed. I also have a Dell Wireless 1505 Draft 802.11n WLAN Mini-Card. When setting the Network mode on my router to Wireless N-Only I am unable to connect to the network. I have been searching all over the internet for how to fix this, but none of the answers suit me. I have my network security set to WPA2 with an AES encryption, like people keep saying so I know that is not the problem. Others say that I need to set my wireless adapter to N-Only as well, but I have not been able to find anything in Google that shows me how this is done. The driver version for my adapter is 22.214.171.124 and is up to date according to Windows.
I have been using a Lenovo W510 laptop with an Intel wireless adapter (Intel(R) Centrino(R) Ultimate-N 6300 AGN). The download speed has been 15-18 mbps on my home network. I just bought a new Lenovo W520 with a Lenovo wireless adapter. The download speed is about 1 to 1.5 mbps. What changes should I make to the router settings so that it communicates properly with the Lenovo wireless adapter?
I have a Telus modem, that is hard wired to a siemens wireless router.The telus modem assigns addresses to the siemens router in 192.168.254.* address range.There are a lot of other siemens routers operating in my neighbourhood and I keep getting kicked off.So I want to connect my MacBook Pro wirlessly through the linksys WRT600N on the 5GHz band.I've disabled the 2.4Ghz band.
I'm having problems with the access restrictions feature on the WRT600N. I do have the latest firmware upgrade, which was released in 2008 I believe. Anyways whenever I totally block a PC from the internet either by MAC or by IP, it affects the internet on the rest of the house. Logins to sites do not work right. Logouts from do not work right. Different features of different sites will not work properly. There also will be a lag sometimes when entering the url for a new site. But as soon as I turn the access restriction off, everything goes immediately back to how it should be working.
I have a WRT600N router. I have one PC that is connected to the router via a wired connection. I also have an iPad (3rd generation) that is connected to the router via a wireless connection. On my PC, I went to speedtest.net and determined that I am receiving like 20MB downloads via the wired connection. However, my iPad only gets approximately less than 2 MB download speeds. I have tried reseting the router and I do have what I believe to be the latest firmware update (Firmware Version: 1.01.36 build 4). I also receive the slow download speeds when I try connecting the other wireless devices. I assume my problem has to do with some sort of configuration setting found in the router configuration page (http://192.168.1.1/). The router is only a few feet away from my iPad so the signal strength is strong. I just don't understand why I'm receiving such slow wireless download speeds.
I have a Lynksys WRT600N. I had DD-WRT on it and it was working great for about a year. One day I changed some minor settings like wireless signal type, reboot it and it's gone. I can not access it from my computer. The network adapter shows "cable unplugged". The lights on the front come on, but I can't get anywhere with it.
I've done all the resets I know how to do, including the 30/30/30 and leaving it unplugged for a few months.
I cannot upload files through http (e-mail attachments, send images to Facebook, send file to virustotal.com) with Linksys WRT600N router. When I remove connection cable from router and place directly in a computer, everything works just fine. I am using last firmware upgrade.
I fought my ISP (frontier) for weeks trying to get their 7500 DSL/modem/router configured in bridge and working into the WRT600N. Finally gave up and put a new Engenius EVR100 behind the 7500 bridge and it came up fine in 10 mins. Now I would like to use my old WRT600N downstairs as a second router and run it in the range of the Engenius DHCP, with DHCP turned off in the WRT600N.
My question is this ... Do I set the WRT600N as a static IP address and use an address in the range issued by the EVR100?And, if so, what would the sub-net mask, default gateway and DNS numbers be? Also would the router address itself (lets say I use 192.168.0.120 from the EVR100 range) be different then the static IP address?
My DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?
When the Wrt600N came out, it was said that the "Reserved" button would be enabled by a future firmware upgrade to support WiFi Protected Setup. Surely in the three or so years this has come to pass.Does anyone have a link to information on using WPS with the WRT600n?
I am using a linksys wrt600N with easylink advisor version 1.6.0042. I am trying to install a video camera and the instruction manual says under "known issues": LinkSys routers have a factory default setting in the firewall menu called "filter anonymous internet requests". If you want to access your camera from the internet you have to uncheck this option."I see this option in the WRT600N manual, but it references a software choice that I don't have.I have gone to the website and downloaded the latest compatible software version, and I still don't have the choice to uncheck this option.
I have the latest flash installed. I am making use of all the options available to this router. USB drive set up as a file server, both radio bands have devices which attach. All wifi security is wpa2 with a complex key string. Also have pc’s attached to all lan ports. I also have all the wireless devices registered on the mac address filter for access set to enable/allow. I have a total of 9 mac address in the list. One lan device is on the DMZ. One address is reserved. Not sure what other details you need.Router is used for online gaming, video streaming, and typical internet browsing.
Writing my first router config from scratch for an 1801. I have wireless devices able to connect & authenticate with WPA. Wired devices can talk with wireless devices & on both interfaces devices obtain a DHCP lease. I can ping web based resources from the FA0 interface; the problem is, LAN devices can't ping has FA0. I'm pretty sure (well a hunch) that this is going to be down to NAT
version 12.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname Router0
Panasonic TV (DLNA Device) - Ethernet WDTV Live Plus (DLNA Device) - WLAN Windows 8 PC - Ethernet Windows 7 PC - WLAN Samsung Galaxy S3 - WLAN
The WDTV can act as a media player for both the Windows 7 PC and Samsung Galaxy S3.The TV can act as a media player for the Windows 8 PC.If I connect the Windows 7 PC via Ethernet, then the TV sees it and can act as a media player for it and the WDTV no longer can.The TV can't act as a media player for the Samsung Galaxy S3 nor can they see each other to use the Galaxy S3 as a wireless remote (Viera remote android app) .Why can my wireless devices talk to each other and my wired devices talk to each other, but the wireless devices can't talk to the wired devices?
I've got several devices (two laptops, Xbox, WiiU, Apple TV, 2 ipads, and an iphone) that can connect to my home wifi network just fine. However, when connected it seems these devices cannot communicate with one another.
Homesharing between my iphone/laptop and Apple TV is no longer functioning. Also, I can not sync my windows media player with my Xbox, and I can not connect my iphone to the Xbox using AirMusic.
Here's my hardware: Motorola SB5101U SURFboard modem, Netgear Wireless N WNR2000 router.
Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:Windowssystem32>ipconfig/all
have the following set up: cable modem>wifirouter>gigabit ethernet switch>to 16 ports throughout house. When I connect a second wifi router to any port around the house, the internet does not work when connecting to that specific router, however, if I use a lan cable and connect direct with my mac or cpu, internet works fine. wifi routers are not communicating with LAN ports
I lost internet from the ISP and parts of our LAN went down.We were able to reproduce the error.Problem: Internet from ISP drops, program using port 10541 within the LAN stops communicating with a server.The computer and server are on the same switch, neither require access to the internet.How we fixed the problem, temporarily: Unplugged the power from the cable modem.How we reproduced the problem: Unscrewed the cable drop to the modem and powered it on.I have checked our firewalls logs and have seen nothing that stands out. I was able to ping the server from multiple computers, including the one that had the program running on it.Also while the internet was down, I tried removing the DNSs from the computer running the program, this made no difference.
I have a cisco 2811 with security bundle with IOS 12.4(13r)T I am planing to use this router as a VPN gateway for company ( i.e)
1. LAN 2 LAN VPN ( Supporting if remote site is having dynamic IP)
2. Remote access VPN for VPN client
I have configured the router ( attached is the configuration) I have not tried to use the LAN to LAN VPN ( first i complete remote access VPN and then check L2L) I tried to use the remote access VPN I am able to connect from vpn client software and got the IP address but unable to ping the servers in LAN.
We ran a D-Link DIR-655 for about 5 years on our home network of 7 desktop computers (LAN) and two laptops (wireless) with essentially no problems. However following a power outage last week the router stopped communicating with the cable modem (WAN port failure?). From the web site we determined that the DIR-825 is a fancier version of the DIR-655 (extra 5 GHz transmitter) so we upgraded to a new 825 three days ago. I did not use the wizard on the CD to set up the new router -- rather did it manually because I thought I'd configure the new router exactly the same as the old one -- this was probably not a good idea in retrospect. (FYI our new DIR-825 is a ver. B1 unit with ver. 2.02NA firmware.
After setting the router up -- it lit up like a Christmas tree and I could see all 7 desk top computers (3 are WIN7 & 4 are WINXP) in the LAN and all would go on-line with no issues. (FYI 3 desk tops are directly attached to the DIR-825 and four attached via a switch). However, when I tried to map the network I find that only 5 of the desk tops we assigned to our named home network -- 2 or them could not be mapped as they were assigned to a "public" network. So while they all still communicate with each other two are no longer in our home network. I do not think this was anything that I did -- knowingly at least.
I logged back on the the router home page but I see nothing that clues me in as to what I did wrong.So I'm wondering how the DIR-825 made these "assignments" and what I can do to redirect the router to bring the other two computers into our home network. (BTW one of the two "miss-assigned" computers is WIN7 and one is WINXP so its not a window version issue).
I enabled dual stack on my rv042g router but its not recieving ipv6 information from my isp. My isp is Time Warner in Milwaukee. They assure me that they are ipv6 ready and assume the problem is on my end. All they want to do is have me connect one computer up to my modem. What good is that when I have a network that needs service. The router needs to be working not just one pc. My ipv4 is working perfectly. It is obtaining all information automaticly.
We have NAM-2 installed in 6500 chasis. Some times in GUI It does not analyse the traffic and shows the error msg"error communicating with RMon daemon". But at the same time we can login to NAM through CLI,
The issue resolves by reseting the module by hw-module switch "" module "" reset but not always and happens not very often,
Device details: NAM application image version: 4.0(1a) Maintenance image version: 2.1(5) NAM Daughter Card Micro code version: 126.96.36.199 (NAM)