I just got a wireless router to use with my Hughesnet modem, and it worked fine but my mom turned off the power strip that everything was plugged into and now it won't work. My dad says it's because the Ivip4IP gateway was messed up or something, and I need to change the wireless router's gateway IP to the computer's default.
View 1 RepliesI rdp into our server 2008 via IP. This is a router on ip 0.1, this is forwarded to my server on IP 0.3. This server was setup with DHCP default gateway of 0.1. We added a new outside connection on IP 0.2. I was talked through the changes so that internal DHCP requests went to gateway IP 0.2 but RDP still used 0.1. I plan on getting rid of 0.1.Where is the setting to change the RDP to use default gateway of 0.2?
View 3 Replies View Relatedhow do i change a default gateway? the current gateway 170.130.110.254 needs to be changed to 170.130.110.2 so my two devices at separate locations can communicate with each other
View 1 Replies View RelatedI have four ASA 5505 devices connected via tunnels. All of the tunnels have a single point of exit to the outside, an AT&T T1 line. Because of issues with bandwidth, I added a secondary line to each site. In this case the secondary line is a comcast high speed internet connection. What I would like to do is set up a route so that any traffic that is going to the internet (browser or email) be directed through the Comcast line and all internal traffic (file transfer, ERP, VOIP) can be directed to the AT&T line. Each has a separate ip address. There is a single default gateway set up on the ASA now.
View 1 Replies View RelatedI want to know could we change or remove the Gateway (highlight) within of Routing Information Sources in OSPF routing protocol? [code]
View 9 Replies View RelatedI recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies View Relatedwe do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies View RelatedI have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies View RelatedI have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
Can a router using OSPF propagate that he is a router with default-information originate... at the same time when he got an own gateway of last resort to an IP-adress? If so, how? I can't get it to work.
View 8 Replies View RelatedCan a VOIP gateway device be connected between a DSL or cable modem and an existing wireless router? Here's my problem. The cable and phone lines come into a box in the garage, that's where the cable modem is. But my wireless router is in the attic on the end of 50 feet of CAT5 cable. I want to add a VOIP modem, but want it in the garage where the phone lines are. It's not convenient to bring a second CAT5 cable back to the box from the wireless router, so can the VOIP modem be connected inline with the router, or in parallel (Y-cable) with it?
View 4 Replies View RelatedI have a cable modem that operates cable tv, telephone, and internet. I am looking for the right router to purchase with the easiest set up.
View 1 Replies View Relatedi cant get my netgear to work on my gateway can you
View 1 Replies View RelatedI currently have Comcast as my ISP.However there are only 4 wired ports on the router and I need an additional 2 ports for my needs. I have a 2wire 38000HGV-B Uverse Wireless gateway. I wanted to know if I could use one of the output ports from the Comcast wireless gateway and feed the 2wire Gateway to achieve the additional ports that I need. Also the wireless router from comcast is so difficult to setup that I don't even use the wireless. The 2wire gateway is much easier to setup and use and I could have wireless available where I don't have it right now.
View 2 Replies View RelatedJust got a never used AT+T Wireless Router (2701HG-B Gateway) from a friend to use with my laptop and comcast broadband connection. I have windows vista, and use IE as my main browser. Can I used, or is it set up to only work with an AT+T connection? I do have all the software discs that came with the unit, but haven't run them as they seem mainly for setting up DSL connection with AT+T.
I've recently bought a WRT120N router, when I install the router using the CD an error occured error 322 New router or gateway not detected. I tried to download new version of firmware but it didnt work.
View 9 Replies View RelatedI can't log into the router. Get 502 Bad Gateway - Model EA4500; Have a USB Drive connected to the router.
Power-off and Powered-Back on - no change.
I have a WRT54GX2 router and my laptop is connected wirelessly to the router. It worked fine before but now, the connection is only local, it's not connected to the internet.On the router, it says: Default Gateway: 0.0.0.0.I think that it should say 192.168.1.1 instead.I tried dhcp release and renew but it didn't work.The firmware version is 1.01.22.
View 3 Replies View RelatedI am currently using an E900 wireless router. The router is on the second story so I have to use a wireless router booster to enhance the signal strength. I have been using the booster for well over a month with no issues whatsoever; however, tonight I attempt to get onto World of Warcraft and I keep getting disconnected every 5 minutes. After I run the diagnostic it fixes the problem and says that the "default gateway not available". I tried restarting the router, restarting the booster, unplugging the wireless adapter, checked the firewall, and also restarted my computer.
View 2 Replies View RelatedTrying to login to my router with the default IP address of http://192.168.1.1
Been working fine forever.. I went in and dumped all my cache on my browers IE and Firefox.
Still getting this error. I have unplugged the router and cable model and also restarted the computer.
This seems to be a recent issue since it was working a few days ago..
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies View RelatedI picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
config setup
protostack=netkey
klipsdebug=none
[Code]....
I have been using this router for the last six months and never had a single problem. Then yesterday out of nowhere internet stopped working and I was not able ping my ISP gateway (both wired and wireless) [Received: Destination host not reachable on both Windows Vista / 7]. Rebooted the router but still no luck. Unplugged / Replugged the net connection from the WAN port and then finally ping was successful.Now the weird this is every time I power on the router the Internet does not work and ISP Gateway seems not reachable, but if I unplug/replug the WAN connection the ping reply starts and internet works without any problem.
View 3 Replies View RelatedI am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies View RelatedI have a Linksys E3000 and I see the gateway (192.168.1.1) listed in my DNS server addresses.
1. Why is this listed here in the DNS?
2. How do I remove it from my DNS servers or stop the router from inserting it into my DNS server list?
FiOS gave me an Actiontec router that every other day is getting into a state where it refuses to give out IP addresses via DHCP. I have to reset the router to get it to work again.This seems ot have started in the last year, I assume due to some piece of equipment I added, or perhaps the VPN software or Windows 7 installed on my work laptop. I've not been able to figure out what is tripping up the Actiontec router, so I decided to try moving the DHCP function over the WRT610N that I have. I basically had the WRT610N setup without DHCP enabled, no NAT and no RIP, so it was basically just working as an access point. I left the Actiontec at 192.168.1.1 and assigned 192.168.1.2 to the WRT610N on the LAN side, while the WAN side is left disconnected.
I disabled DHCP on the Actiontec and enabled it on the WRT610N. I also set the DNS server to 192.168.1.1 so it would go to the Actiontec for name resolution. Using nslookup from a command prompt on a PC wireless connected to the WRT610N, I can see that names are indeed getting resolved. However, it looks like the WRT610N is setting itself up as a the gateway at 192.168.1.2. When trying to ping something out on the net, I get a message back saying that 192.168.1.2 is reporting the address as unreachable.
I assume this is because the WRT610N is handing out its own address (192.168.1.2) as the gateway. Is there anyway to get the WRT610N to hand out a different gateway address than itself? Optionally, is there a way to get the WRT610N to route requests coming to it over the Actiontec?I suppose I could just ditch the Actiontec altogether, but it seems a bit easier to use to setup port forwards and the like for various servers we have running. It also has a coax MoCA interface which I believe our FiOS set-top boxes use for their internet connectivity, so I don't want to lose that.
I bought this wonderful voice gateway off the internet from someone. So not sure if they ever used it with Comcast.So far I hatve had no internet once I plug it to the cable. I have asked Comcast tech for activating this device. However they say it is not supported and they have tried sending it the Activation signal but they say it fails. I can see all lights lit up and go green when I connect this device to the cable, is there a firmware upgrade for DPQ3925 ?
View 2 Replies View RelatedI'm unable to access my linksys wireless g broadband router (WRT54G)'s access gateway. (192.168.1.1)The gateway page doesn't load, at all. It doesn't ask for the user or password at all. On any of my internet browsers (firefox, and internet explorer)Anyway of fixing this would be appropriate.
View 2 Replies View Related