Determining IP Address Of NetGear FSM750S Switch?
May 5, 2011
I have a Netgear FSM750S 48 port managed switch that I inhereted from the previous LAN guy who was gone before I got here. I don't know what IP address he was using for the swithc - I have a decent guess for the username/password; but I'm not 100% sure on those either. how can I determine what this devices IP address is so I can telent into it? Do I have to reset the switch to factory config? And if I have to reset it, how do I do that? There aren't any factory reset buttons anywhere on the chasis. [URL]
View 8 Replies
ADVERTISEMENT
Sep 29, 2012
I am installing a network in my small business and was given a spool of Cat5 cable to run wires... I know the length in feet of cable that I was given, but I was wondering if there is some kind of markers on the cable to tell me how much is left... I will be charged for it by foot after I'm done, and I want to know how much I've used. Do I have to just use a measuring tape? Seems unnecessarily complicated... I've checked the wire but can't see any marker of the length remaining.
View 1 Replies
View Related
May 20, 2011
Just wondering if there are any methods or commands, natively, in the asa5510 for determining all traffic in to and from a certain server passing through the asa. This would be without a syslog server or something similar.
View 3 Replies
View Related
Mar 25, 2012
I have a 7609 with a Flexwan module with a PA-POS-1OC3. Is there a command to determine they type of SFP in the module ? sho controllers POS didn't provide the SFP type.
View 2 Replies
View Related
Jan 9, 2012
We have a PIX 501 and I'm in the process of replacing it with a ASA5505. We're currently using the 501 for a site-to-site vpn for disaster recovery purposes and I'm trying to verify the number of concurrent connections we can have.
View 1 Replies
View Related
Feb 4, 2013
Aironet 2600 and 3600 series. I need to know their maximum distance (at least theoretically, in Line of sight, eliminating all other factors...) in order to choose the right number of AP to provide enough coverage for a specific area. If an exact number is not available then can you show me how to determine it?
View 8 Replies
View Related
Oct 13, 2009
Is it possible using any module in CW to get the MAC address and IP address of all switchports on a 6500?
View 6 Replies
View Related
Feb 7, 2011
I am trying to determin if Jumbo frames are enabled on out Nexus 7000, and I am getting mixed info back from the swtich.I looks like the system jumbo MTU size is 9216 by default, but the interfaces all say the MTU of the interface is 1500 bytes. According to this article, the interface MTU should read 9216 is the jumbo frames are enabled globally. Is this correct. Is there a way to verify if Jumbo frame support is turned on? [code]
View 4 Replies
View Related
Jan 16, 2011
is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies
View Related
Aug 18, 2011
I just need to know what numbers to put in this Server IP AddressI tried putting a 0 and 1 at the end.
View 5 Replies
View Related
Aug 31, 2011
I purchases a Sony Vaio Intel i3 2 weeks ago largely because its a Sony and because of the Wireless Display it offered using Netgear Push2TV 1000.My first day the WiDi worked perfectly but then I got busy installing and updating the computer.And now, two weeks later, when I attempted to connect to P2TV the TV screen just says "Could not obtain network address".I updated the drivers. Nothing changed.Reset the adapter. Nothing changed.Enabled My Wifi/checked for Intel Wireless PAN DSCP server/checked firewall. Nothing happened.I looked up other people having the same issue and there seems to be a lot and they all agree that there is no cure in sight. Apparently, BestBuy even had the balls to tell some of them to restore the computers to its original factory setting to resolve the issue which is pathetic.
[code]...
View 4 Replies
View Related
Feb 4, 2011
I have a Netgear DG834PN Router. Connected to it usually are 2-3 laptops (XP, Vista, 7) wirelessly, a Xbox 360 and Win 7 PC via cables, a wireless printer and often an iPod touch, however PS3s, mobile phones etc are connected occasionally.
It had been functionally normally.until we changed ISP after ours was taken over (we didn't change but the provider obviously now has). However, since then (1st Feb) we've been having connection issues, probably an IP address conflict where items can access the router but not the internet.
The iPod and Xbox sometimes don't connect, as do the laptops often after been powered up from a sleep. Yesterday, when powering up one of the laptops, I got an IP address conflict message. Restarting the router sometimes works, but mostly it allows one device on and not another.
The printer has a static IP address (192.168.0.4) that I had to set up to get it working, but this has been active for months now without issue. I've had a look in the router settings and it's set up for DHCP as default with IP addresses from 192.168.0.2 to 192.168.0.254 so I don't understand why it has this issue suddenly. I had a look at the connected devices list, and everything appeared to have its own IP address.
View 13 Replies
View Related
Jan 10, 2012
have an unknown mac address listed in my router's connected devices pane. There is no ip address or device name listed. I know the mac addresses of the machines I have put on the internet, and i don't recognize that one. Router: Netgear N300 WNR2000v
View 2 Replies
View Related
May 3, 2011
I have an old, old Netgear 814v2 that I'd like to use as a switch to, in effect, extend my wireless range and allow other old hardware that is NOT WPA-capable to connect to my network. From what I've read, it ought to be fairly easy: disable DHCP on the Netgear, and connect the Netgear to the router via a LAN port not the WAN port. This should, I gather, convert the former router to a simple switch.Having done this: if I connect to the Netgear-turned-switch via a LAN port (cable) everything works fine (the computer gets valid IP's, subnet mask, DHCP server and DNS server IPs). Great! It's a switch!But if I connect via wireless it gets an oddball IP address out of range of the normal IP's for a client computer, and no default Gateway or DNS server IP's. Which is to say, hardwired network connection through the Netgear-turned-switch works fine; wireless works not at all.Why would the Netgear-turned-switch fail to pass through for wireless, and work just fine for wired? What am I missing?(For those who are concerned, if I get this to work, I'll provide security on the Netgear by specifying MAC addresses that can connect.
View 3 Replies
View Related
Jan 3, 2012
This is an older desktop, Been utilizing the net gear to get on the Internet for months and it was working fine,shows it is connected to ssid but ip shows up as 0.0.0.0 I have other home computers hooked up and work g so I located there ip address, can I input it myself ? If so how?
View 2 Replies
View Related
Dec 19, 2011
basically we got sent this new router from Orange (our ISP) and we have had problems with it for the last week. The router model is the Netgear N150 DGN1000. Sometimes I connect it will be absolutely fine, but then the next time I log onto my laptop it can't identify the network, it says connected but doesn't have the globe in the bottom right hand corner of my screen. Then we have to reset the router a few times everytime until it recognises it, even though the settings are saved when we connected last time. It is the same with my sisters laptop. We both have Atheros network adapters so that may be a compatability issue with the router, but my brother connects fine on his everytime. A similar problem occurs with modern warfare 3 on my ps3, it won't let me sign in to playstation network half the time and keeps saying NAT type failed, even though NAT is enabled on my router. get this problem sorted and to get a consistent network connection that connects every time that would be great. We changed the security type to WEP on it a few days ago from WPA and that meant we could sign into modern warfare 3 some of the time rather than never, but we are still having issues.
View 8 Replies
View Related
Dec 16, 2011
I recently purchased the netgear n300 ADSL2+ modem router. I have tried all day to get it to work, but I have not have any success.
ISP: Verizon (Now frontier I think)
DSL light will be solid green, along with the port, wifi, etc... But the internet one stays solid red.I've tried changing dns settings and things, but to no avail. Though I am able to login to the router, and I can get internet if I directly connect to the modem.
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersRobert>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Robert-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid[code].....
I noticed in the router settings that the internet port had no ip address, as in it was just 0.0.0.0.
View 19 Replies
View Related
Apr 21, 2012
I am trying to add a new computer to my wireless statione access list but have not been successful. I got the ip address of the computer i was trying to add, my issue is how to add it to the list. i tried adding the details and filling in the device name and MAC address but kept getting the error message "invalid MAC address.please enter again.
View 1 Replies
View Related
Jun 20, 2011
I have a USB Netgear WN111v2 that has been working perfectly up until now, it can't connect to the network and trying to manually set up the addresses, reinstalling drivers, and trying a system restore haven't worked. Even though the router has a lease for the computer on 192.168.1.11 it's doesn't work, although it will show that it's connecting, it won't ping anything, including the router... WZC utility is stopped?
View 4 Replies
View Related
Feb 22, 2012
Trying to setup secure net but when I type in the router IP Address, it shows Netgear, Type in printer IP address and it shows Linksys. How can I access my Linksys to make changes? I believe the Netgear shown is Comcast modem...
View 9 Replies
View Related
Sep 24, 2011
I am experiencing constant DNS issues page not found errors after about 10 clicks it seems to work, and actually get to the page, sometimes it takes longer or i may have to resete the modem again for my system to work, now i have a computer lan buisness with 10 computers connected to it and the internet speed is 4 mbps, i have called the internet provider they did some test, and the modem seems fine they have changed my modem 3 times for that reason , so i know its not the modem , i have switched cables connected to the modem, i use to own a hub i thought that was the problem, so i bought a NetGear's FS116 switch and the problem persists, i have switched over to different inernet browsers , that didnt work, changed my computers modem to assigne ip addresses , and that didnt woerk, also changed my dns servers from my modem by the ones provided by my service provider , and that didnt i am stuck. i have a 15 ft cable connected from my modem to the switch. and all my computers connected to the switch, the problem seems to be more when i have more then 5 computers running at the same time. i have also switched the 15ft cable and the problem still persists, error not found could me a config with the lan settings or dns error
View 3 Replies
View Related
Jun 18, 2012
I an on this form from my cell right now.. so, the computer i want to get Online with is a desktop and i have been days with this problem.
View 14 Replies
View Related
Dec 27, 2011
I'm connected through the router, a few times a day I cannot open web pages, getting error: Error 105 (net::ERR_NAME_NOT_RESOLVED): Unable to resolve the server's DNS address.Skype continues to work. Here are the results of pinging:
Quote:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSri Guru>ipconfig /all[code]....
One technician said that this is the providers problem, but I don't think so. When I restart the modem everything works.I have a Netgear WGR614 v9 router.I use ESET 5 security. Btw, connection drops on all computers connected through the router, so it's not my firewall.
View 3 Replies
View Related
Feb 1, 2013
I recently bought a Netgear switch in order to hook up to wired PCs to my modem. I also have a ASUS n53 wireless router that I am trying to connect to the switch. The problem is I can't seem to get internet access to the wireless router I have tried setting it up as an access point, I have tried disabling the DHCP on it.
View 5 Replies
View Related
Jan 7, 2011
So my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies
View Related
Aug 24, 2012
I am running XP Professional 32 bit SP3 on a Dell workstation.I am in a serviced office with internet connection via single ethernet port. This is set up as a VLAN for which I have 4 assigned IP addresses.I am using a Netgear GS605v4 switch to create a small network on my side of the port. Hooked to this is the workstation, the mybook live, and a laptop.All 3 connected components are assigned their IP addresses by DHCP. Both the workstation and the laptop can see the internet without difficulty. The networking of the components is another matter. Focusing on the workstation for the moment:On the workstation, I can ping the mybook. I have always been able to see its upnp logo in My Network Places, and double clicking always takes me to the web browser based dashboard where I can set up the device. I was initially able to see the public folder in My Network Places too, and could map a drive to this in an Explorer window. Typically after some time, the mapping would be lost (even without re-booting the machine), but I would be able to delete the connection and re-map it. After several attempts at this I could no longer map the drive or see the public folder in My Network Places anymore. After much internet searching and playing with lots of the suggested fixes (checking all required services available, matching user names between XP and the drive, playing with 'net view' etc) I was finally able to see and map the public folder yesterday by playing with the 'enable netbios' function in network connections (currently set to 'enable' from 'default' though this had not made any difference previously). I could see the drive in 'net view' though no master browser was listed, and once again map to the public folder, and access files on it.On turning on the workstation this morning I find that the mapping has again been lost. This time net view is back to reporting a system 53 error. I can ping the drive and use the dashboard, and I can see the public folder in My Network Places, but clicking it or mapping to it results in the usual 'network path not found' errors. The laptop is running Windows 7 and has not lost its mapping overnight, and can still access the public files.
View 2 Replies
View Related
Feb 23, 2012
I am trying to set up a VLAN on my Netgear switch (GS105E). I want to create two separate networks and I want both of them have internet access.
I have configured port 1 and port 5 as vlan1 and port 2 to port 4 as vlan2. I plugged a cable from the router to port 5, and the computer on port 1 has internet access. However, the computers on port 2 to port 4 have no internet access.I had tried to create VLANs with the router but had no luck.
View 3 Replies
View Related
Jan 9, 2012
I have a router TP-Link (without wireless) connected in my modem wich have this subnet : 192.168.0.*, that work fine. But I need a wireless connection too, my wireless router had this ip given by the TP-Link router: 192.168.0.13.
I have a NETGEAR WIRELESS-G ROUTER WGR614 which gain 192.168.0.13 but I need that gives ip's in the same subnet that TP link router. If the person connect to my wi-fi it should receive an ip like 192.168.0.*, I already try to disable the DHCP server in the NETGEAR but it's not working too. How can I do that ?
View 2 Replies
View Related
Oct 24, 2012
I need to upgrade my switch to something that has 24 ports. This is for home, simply to sling media around the house, etc. So 3-4 computers, boxes, AVR's, HTPC's, blah blah blah - just the usual stuff.
I was looking at the Trendnet TED-S24DG and the Netgear JGS524 (both are under a couple of hundred bucks). The cheaper the better to a degree - rack mount is preferrable. Both are unmanaged. Jumbo frames?
I need to buy a new router for my network (using DIR-655 for last 4-5 yrs). Would like to move to a dual band product.As I live in Canada and would like to purchase VPN to rid the geo tagging and enjoy US media content. I plan to buy a wifi router that supports VPN to accomplish my goal.
So, from modem, to router, then to a 24GB port switch, devices include 3 wired computers, tvs, boxes, players, blah blah blah, etc.
Placement of the router is in my basement (has to be as this is where all my network/modem/server rack). I plan to also purchase an AP and place it on the 2nd floor of my home (2200sq ft) for coverage in the house.
Question is, once I add the VPN to get US content, there will be times when I want my own PC to NOT be on the US VPN.So, based on the above which dual band router under $130 and how much for the AP? And how do I setup it up so that my personal PC and be on and off the VPN?
Right now I can get a E4200v2 refurb for 60 bucks from NC$X? I was looking at Asus N66, but perhaps its too much for my needs?
View 19 Replies
View Related
Jan 5, 2012
how to configure a server with net gear switch . I want to restrict access for a few users and use the netgear switch for file sharing between the small network. its got auto configuration .
View 3 Replies
View Related
Jan 27, 2012
I am relatively good at installing and troubleshooting smaller sized networks... I am having trouble with one of my customer's networks and I think I have the problem narrowed down. r issues.I have a customer with a FS726T switch and ~20 computers connected to this switch running DHCP assigned addresses.The switch is assigning addresses in the 10.0.0.xx rangehe customer currently has an old T1 line coming into a Cisco router, which then directs traffic to port 20 on the switch.The problem is, we are replacing the old T1 line with a newer 50mbps cable connection.The cable company pre-configured their router with a static IP address the 68.116.xx.xx range. The Subnet is also different than the Netgear's subnet. I would like to keep the old T1 connection in place. I believe they have data that needs to go to their mainframe/backbone server at corporate.
I cannot log in to the cable modem. IT is an SMC SMCD3G with a staic IP. I tried changing my PC's IP address to the same gateway but cannot get into the cable company's modem, even using a static IP with the same gateway as the modem's gateway address. I don't want to reset the modem/router and lose the cable company's settings.I am pretty sure for the devices to communicate, the following has to be true?:1) Cable modem and FS726T must be on the same 10.0.0.xx IP range?2) Cable modem and FS726T must be on the same 255.255.255.0 subnet mask?
View 7 Replies
View Related
Dec 12, 2012
I have a Netgear N600 connected to a modem. I want to connect a switch to the Netgear N600, my question is, will multiple computers connected to the SWITCH have access to the internet?
Router : Netgear N600 [URL]
Switch: Rosewill RC-405X 10/100Mbps Switch [URL]
View 4 Replies
View Related
Dec 9, 2011
I need to setup my Netgear as a switch/access point. I need the following set-up. My ipconfig /all reports:
View 27 Replies
View Related
