Remap URL To Different IP Address?
Feb 14, 2012
I have a print server that uses ip address 192.168.1.74. The share for the attached printer is 192.168.1.74/LP1 Problem is I have a server system that will not accept the "/LP1" part as a valid network printer device. I believe I can get around this if I can remap this complete url to a new ip address...
so: "192.168.1.74/LP1" ---remapped to---> "192.168.1.75"
so a user can send prints to 192.168.1.75 and the print server will pick it up as expected. How can I do this and what is the best way? My network is small but I do have control over local DNS as well as our firewall. Not sure if I need a proxy of some kind setup to do this... perhaps PFsense might be a place for me to start?
View 8 Replies
ADVERTISEMENT
May 15, 2012
Recently purchased a new computer and need to remap to our network drive. the password to the drive is not working so i need to change it.
View 1 Replies
View Related
Jul 16, 2011
I switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies
View Related
Mar 6, 2012
I am having an issue where occasionally the Sidewinder starts to see my internal RFC 1918 address instead of the configured external address of my firewall. This is for peering between the two. The error they see on the Sidewinder is:So instead of seeing the external peer address he sees a 10.220.3.18 address. We are not sure what triggers this becuase normally he see's my 63.117.98.222 address.
View 5 Replies
View Related
Jul 8, 2012
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies
View Related
Feb 28, 2011
Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies
View Related
Jul 3, 2011
I have a Linksys WRT54GS v5.1 router running firmware 1.52.5.I am trying to use Linksys IP Phones SPA942, but these do not seem to be able to log on and just show "Initializing network" even though the MAC address appears in the router with an IP address.The strange thing is that I already have 4 SPA941 phones that work with no problem and just log on to the network.Is there something about the SPA942 that I need to configure differently, I have factory reset it with sucess, but still unable to log on to the network.
View 1 Replies
View Related
Oct 13, 2009
Is it possible using any module in CW to get the MAC address and IP address of all switchports on a 6500?
View 6 Replies
View Related
Jun 3, 2012
I have been trying to clone my PC's MAC onto my Linksys WAG120N adsl2+ modem router .
I click the the clone my PC's MAC button in the MAC address clone tab. I get the following error :
"Mac address cannot be the multicast address"
The MAC address starts with 1C:C1:XX:XX:XX:XX
I even tried to update the firmware.
View 9 Replies
View Related
Aug 23, 2009
I recently switched routers to the DIR-615 and I'm trying to troubleshoot why one of our laptops keeps losing the IP address and gets a self-assigned IP address. I see the following messages in the log, I am wondering if the reason codes are listed and explained somewhere? I tried searching the manual but could not find any information.
View 9 Replies
View Related
Jun 1, 2012
We have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
View 1 Replies
View Related
Apr 26, 2011
On my cisco IOS 12.4 router,Can i make it so only lets say mac address 11:22:33:44:55:66 able to use ip address 10.10.10.2?I want this so that only this IP can configure servers, and so if the computer using it is turned off, any other device cannot use the IP address.
View 6 Replies
View Related
Mar 2, 2011
I recently configured and installed a 1941ISR for a customer. The customer purchased a 25-User SSLVPN license with the router, and I configured it for remote SSLVPN access. This is working nicely except for one issue: when users initiate an SSLVPN connection request by browsing to the assigned webvpn gateway IP, they get the "There is a problem with this website's security certificate" browser message. They are in the process of working with their DNS hosting provider to get a DNS entry assigned to the IP address so the users won't have to specify an IP address in the URL address box, but they will continue to get the certificate error until/unless I can figure out how to resolve the issue.
I've tried the following "How to make IE8 trust a self-signed certificate in 20 irritating steps" that I found via another forum link but with no luck:
1.Browse to the site whose certificate you want to trust.
2.When told "There is a problem with this website's security certificate.", choose "Continue to this website (not recommended)."
3.Select Tools->Internet Options.
4.Select Security->Trusted sites->Sites.
5.Confirm the URL matches, and click "Add" then "Close".
6.Close the "Internet Options" dialog box with either "OK" or "Cancel".
7.Refresh the current page.
8.When told "There is a problem with this website's security certificate.", choose "Continue to this website (not recommended)."
9.Click on "Certificate Error" at the right of the address bar and select "View certificates".
10.Click on "Install Certificate...", then in the wizard, click "Next".
11.On the next page select "Place all certificates in the following store".
12.Click "Browse", select "Trusted Root Certification Authorities", and click "OK".
13.Back in the wizard, click "Next", the "Finish".
14.If you get a "Security Warning" message box, click "Yes".
15.Dismiss the message box with "OK".
16.Select Tools->Internet Options.
17.Select Security->Trusted sites->Sites.
18.Select the URL you just added, click "Remove", then "Close".
19.Now shut down all running instances of IE, and start up IE again.
20.The site's certificate should now be trusted.
I followed all 20 irritating steps to the letter, but am still getting the security certificate nat.Now when I “Continue to this website (not recommended)” and click on "Certificate Error" at the right of the address bar, the certificate error windows says “Mismatched Address”.Is there a way that I can get this fixed without resorting to a 3rd party CA?
View 5 Replies
View Related
Feb 25, 2011
I need to change the ip address on my router same ip address as myDlink router?
View 6 Replies
View Related
Mar 15, 2012
one of my friend can tell me my ip address by using gmail. He don't have any software to know the ip address. but he can tell me my ip address. how did he know it. is my wi-fi not safe? or other? and can we know it any way?
View 6 Replies
View Related
Dec 30, 2011
What is WAN IP address
View 2 Replies
View Related
Dec 23, 2011
We have moved house recently and changed internet provider. The laptop and x-box have both connected ok. However the main pc will not connect. The wireless router says that it is connected but the icons of pc-router-internet is not connected. when you hover over the pc icon, there is no IP address.
View 1 Replies
View Related
Jan 17, 2013
How exactly do you change your IP Address?
View 8 Replies
View Related
Jan 27, 2011
Me finding my friends IP. I know its not good finding others IP but i need that seriously.
View 4 Replies
View Related
Sep 9, 2011
I'm wondering is there a way that i could actually change the IP address of a computer based on its MAC Address that is connected to a network via switch only ? By running some bat file ? I only manage to change a target computer ip,dns,subnet via running the bat file on the physical computer but not through a network with switch.
View 11 Replies
View Related
Oct 6, 2011
need to understand about IP addressing on printer. At work, we have printers with NIC. When the printer was installed first time, I printed the configuration and noticed the printer IP starts with 192.xxx.xxx.xx but when the computer person in-charge installed it the printer IP
[code]...
View 3 Replies
View Related
Mar 22, 2011
I have just had a cctv system installed on my house and am currently working away from home, how do i connect to my ip address to view the cctv images?
View 2 Replies
View Related
Jan 19, 2011
I have a PC that I would like to access remotely though VPN. My internet service provider is Time Warner Cable and it provides me with a dynamic Ip address.
View 5 Replies
View Related
Oct 3, 2012
192.168.1.1 this is ip address is which country&which area?
View 4 Replies
View Related
Mar 15, 2013
I need a user and passs to access my ip...
View 2 Replies
View Related
Jan 16, 2012
I am trying to find a way to find the netid and hostid of any given ip address, given any ip address, I know the left side the IP address is the netid and the right side of the ip address is the host id but I am pretty sure there is more to it than that.
View 1 Replies
View Related
Jan 7, 2013
I have just moved my desktop to another house and now I cannot access the Internet. I have a USB adapter which has connected to the hub and has an excellent connection but it keeps trying to aquire network address. Then stops and starts again.
[code]...
View 14 Replies
View Related
Dec 19, 2011
I just upgraded to the Belkin N750 DB router from the version just below it and couldn't get the wireless card (Ralink RT2760) in my daughter's dual-boot WinXP/Ubuntu 10.04 to connect to the WPA security setting (WEP only) on the Ubuntu side. There is an updated driver, but it's way above my Linux skill set, so instead I just disabled security completely, and used the MAC Address filtering to add all of our household devices.This solved her connection problem, but I am wondering if there is any danger to this method that I might not have considered
Originally Posted by BelkinMAC Address FilteringThe MAC Address Filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client on your network to allow network access to each. To enable this feature, select "Enable MAC Address Filtering". Next, enter the MAC address of each computer on your network by clicking "Add" and entering the MAC address in the space provided. Click "Apply Changes" to save the settings. To delete a MAC address from the list, simply click "Delete" next to the MAC address you wish to delete. Click "Apply Changes" to save the settings.
View 8 Replies
View Related
Feb 21, 2013
For the past 2 days I have been having a problem with my laptop taht, actually a bit old. I also have another pc, a desktop, with a d-link modem and wireless router (DIR-615). The problem is that I can't go on the internet with my laptop, because of a certrain error on the Intel PROSet Troubleshoot: "Did not receive IP addresss", in fact the IP address was written as 0.0.0.0, and when I open the internet browser I can't go on to any page. IO have tried everything, believe me, from switching off every thing, to reinstalling the router, but nothing seems to resolve the error.
View 12 Replies
View Related
May 3, 2011
when I did ipconfig it gave me 174.61.85.170. What to do
View 3 Replies
View Related
Mar 8, 2011
This is a home network and I do use a laptop and a wireless router however I have plugged my laptop directly into the router.
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersSammm>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : demongrunt7-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
[code]....
View 5 Replies
View Related
Jul 9, 2012
we had servers with 10. addresses and they now give out 192. addys when pinged. The addresses haven't been changed manually but what might cause this?
View 1 Replies
View Related
Feb 4, 2013
[CODE]I have just purchased a new wifi repeater, and everything works fine except for 1 of my tabletsAfter checking things it seems that when the repeater is plugged in the tablet has a different IP address, than when it is unplugged I have 2 mobiles and another tablet and all are working fine.
View 14 Replies
View Related
