1 Laptop Connected To 2 Wifi Signals
Apr 19, 2011Can I connect my laptop to more than 1 wifi signals.
View 2 RepliesCan I connect my laptop to more than 1 wifi signals.
View 2 RepliesMy laptop connected to internet with wifi, but it cannot use even my laptop detect connected, when i run trobleshooter it's show 'no valid IP address' even i already set up to automatically detect , restart my wifi router and unplug doesn't make any changes
View 14 Replies View RelatedWe just moved and got a new ISP, and I have not been able to get a good connection through wifi. When I am connected, it usually goes really slow, and drops every so often. It says that I have 5 bars. I sometimes get a decent connect, but it only lasts a couple minutes. My sister has no problem connecting to the wifi at all on her laptop. I also have never had any problems connecting to wifi before, and I have been able to connect and have decent speeds at my friend's house. I'm on windows 7 the router is a Motorola
View 7 Replies View RelatedI installed the DIR-655 on my home network a couple weeks ago to replace an older model D-Link that failed.
I'm having trouble with my laptop maintaining a connection to the network ever since.
Details:
Firmware Version : 2.00NA , Wed, 12, May, 2010
Hardware Version: B1
Desktop WinXP hardwired to router
Blu-Ray player hardwired to router
Dish Network received hardwired to router
Laptop Win7 wifi
Android phone wifi
CenturyLink DSL
It seems that the wifi stays up until I try to access the internet via the laptop. After a few seconds, the laptop will disconnect, and many times the router seems to reset itself, though not always. This does not happen when using a hard-wired connection. Using the wifi-enabled Android phone doesn't seem to affect the network.
Sometimes the wifi comes back up pretty quickly, but other times it does not. Earlier today, the internet globe light on the router turned from blue to amber. I had to reset the CenturyLink DSL modem for it to work again.
When the network goes does, I get a message on my desktop that a network cable is unplugged, and the network disappears from my available wifi networks that I can see with the laptop. Sometimes I get the "limited connectivity" message.
I have tried changing the 802.11 mode around, and I've changed from Auto Channel Scan to Channel 1. Neither of those have fixed the problem.
I receive wifi from an unsecured Linksys tower near by what can I buy to strengthen that signal will a wifi signal repeater work
View 1 Replies View RelatedI just bought a laptop installed with Windows 8. I want to connect my iPhone to the Internet through the laptop. I have tried using Connectify to set up a WiFi hotspot. It works only with WEP and my iPhone can connect to the Internet but my iPhone disconnects from the hotspot after a while and I need to restart my Connectify hotspot, which is really annoying.I googled online and find that I can use the netsh command to set up the hotspot. I run command prompt in administrator mode and type in the following:
netsh wlan set hostednetwork mode=allow ssid=adhocnetwork key=password
netsh wlan start hostednetwork
And then I share the wired network through control panel > network connections > ethernet > properties.I connect my iPhone to the hosted network and typed in the password. I see a tick next to the SSID, meaning it can connect to the hosted network.I also check the status of the hosted network. Both IPv4 and IPv6 connectivity show Internet.But when I open Safari on my iPhone, it says no Internet.
I use a laptop and recently the wifi has stopped working for me. I can still connect completely but it says with "limited access," which results in me being unable to access the internet at all. The rest of the computers in the house work fine on the wifi and I double-checked the securtiy settings (WAP2 and all that) and it seems fine. What can I do? Tethering to my phone allows me to get on the internet and the computer connects successfully, but no websites will load whatsoever.
View 8 Replies View RelatedI got a brand new HP Pavilion dv7-6c20us laptop yesterday. I brought it with me to a buddies house last night, and it was working just fine.
When I got it home today, I set up the Internet connection and everything seemed fine. I started up a downloader for a video game (Diablo 3) and saw the DL speed climb up to the usual 800-850kb/s that im used to seeing on my desktop PC. It slowly started to decrease in speed, though.. All the way down to 80 bytes/s.. and then it stopped. The icon in the lower right side of my screen told me that I had a Limited Access(?) connection.. i then diagnosed the problem.. and it repaired it saying that "The Connection between your access point, router, or cable modem and ther internet is broken" I thought that it could be just because i was upstairs, and my router was downstairs... it should still be within range.. but i couldnt think of anything else. So i moved downstairs and i got it again sitting 5 feet away from the router.
It stays connected and then for no reason at all it just dissapears..or loses the connection.. when instructed it will repair it.. only to have it happen moments later.. I just tried surfing the internet without having the downloader for the game going and it took longer, but it still happened 5-10 minutes later.
For the time being, I just plugged the laptop in directly to the modem.. kinda ruins the point of a laptop though, you know!
My Router says "NETGEAR RangeMax Next Wireless Router WNR834B..and I have a Motorola Surfboard Cable Modem - SB5101n
Have a new Gateway laptop running W8. I have to use Windows diagnostics in Sharing centre to reset the connection although it looks like it is still up.( page cannot be displayed ). Once reset and fixe all is ok until pc goes into sleep mode, then I have to reset again.
View 1 Replies View RelatedMy laptop will not stay connected to wifi for more than a few seconds before 'limited access' appears. It connects and disconnects repetitively.i have a 3mobile wireless dongle. Other laptops stay connected no problem and i am always beside the dongle with full coverage. if i click the network icon several times on the bottom right it reconnects for a few seconds again,I have discovered that if i run 'funkypool' in the background the connection generally stays, but not 100%, but 90% anyway.this may possibly be because its java and always refreshing itself i think. it doesn't matter whether or not im plugged in or using battery but i did change the controls for automatically putting the wireless to sleep mode so i doubt that unless ive done it wrong.
View 2 Replies View RelatedWi-fi is blinking but not getting the surrounding signals
View 3 Replies View RelatedA bunch of stuff from my laptop was restarted and uninstalled. Now my laptop doesn't even pick up a signal
View 1 Replies View RelatedI've had my computer for maybe a year now, and I have not had problems with my wireless before. Two nights ago I found that I lost internet, and when I tried to reconnect there were no connections available.
My wireless IS on, and my mother's IPad uses the same router as my laptop does for internet and she gets internet with no problem, so it's not the router. I've tried rebooting the computer, disabling and reinabling the wireless, shutting down the computer for the night and trying in the morning, and none of these things worked.
i have a packard bell network.i formatted the whole laptop.and now my laptop doesnot show any wireless network,however connects to dial up connection.i am using windows 7 ultimate 32 bit os
View 1 Replies View RelatedWi-Fi adopter is not detecting the signals? No view is available.
View 1 Replies View RelatedWell while browsing net on my mobile/laptop suddenly the Wifi get disconnected. But the wifi of access point does not drops. Its connected to the router in which wifi drops.Also the net on my desktop connected to the router via ethernet cable, does not go offline. I re,ain connected to net via Desktop even when wifi drops.
View 14 Replies View RelatedI have a problem on my DIR-652.My wifi signal is not detected over the past few days. I went through the settings, everything is good. Outside, in the page information device, wireless radio is off. How to put it ON?I am attaching the screen print.
View 2 Replies View RelatedMy Gateway laptop has stopped sensing wireless signal. It was working just fine a few hours ago, then after I pulled it out of hibernate it stopped sensing the signal. I have switched the button off and on at least 3 times, tried restarting and turning off and starting. Have also tried the Fn-F2 a number of times but still no luck.
View 3 Replies View Relatedi have linksys modem modell wag200g annex-A and stc modem (saudi Telecom company) how can i expand wifi signal to other room
View 1 Replies View RelatedI have D-link 524 router, my problem is that its signals are not being detected ( the devices we connect are ipad 4, htc wildfire S, nokia e-5 . these devices detect other wifi and connect to them.
View 14 Replies View RelatedI have a WLC 4404. I added a new AP to the network and it is associated with the WLC now. But still its not braodcasting the ssids. I compared the configuration with the ones installed before and configuration is same.
View 9 Replies View Relatedi receive my router signals at my laptop but no internet access. i am receiving this problem from last 2,3 days. Before this it was working fine. I have reset the router settings many time but no results. i get the signals at my laptop but i cant access the internet . some times i got DNS server error.
View 1 Replies View RelatedI have an Aspire 7520 laptop and want to use it wirelessly on my router, it will not connect or even pick up the signal. I have no problems when i connect via the patch lead. i have uninstalled and reinstalled the wireless driver and i have checked to make sure i have an upto date driver as well. I run off vista, whats confusing me (doesn't take much) is that it was ok when i had my bt router but then changed to sky and it hasn't worked since.
View 5 Replies View RelatedI have a Wi-Fi booster that can connect to remote distance networks, and I want to share the Wireless Networks that the booster connects to all the local computers in its range (maybe in Ad-Hoc?). The computer that has the booster has it's own separate built-in Wi-Fi.
For example, the booster gets a signal from Wi-Fi network A, and I want Network A to be broadcast to the computers who can't receive Network A's signal. I really don't mind how this is done, preferably without having to buy new hardware.
Region : Australia
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I have TL-WR740N router. I dont know how to stop and start wifi signals.
I have a Wi-Fi booster that can connect to remote distance networks, and I want to share the Wireless Networks that the booster connects to all the local computers in its range (maybe in Ad-Hoc?). The computer that has the booster has it's own separate built-in Wi-Fi. Is this possible in Windows 7 Home Preium?
For example, the booster gets a signal from Wi-Fi network A, and I want Network A to be broadcast to the computers who can't receive Network A's signal. I really don't mind how this is done, preferably without having to buy new hardware.
i have bootcamp installed on my macbook pro and the windows side wont pic up my wifi signal. It did work once and then wen i had a mac update download ever since then the windows side wont recognize my WiFI name or pw,..
View 3 Replies View RelatedI have D-link 524 router, my problem is that its signals are not being detected previously it was working fine( the devices we connect are ipad 4, htc wildfire S, nokia e-5 . these devices detect other wifi and connect to them.
View 2 Replies View RelatedI used to have an HP Pavillion p6340f desktop computer, and then I decided to build my own. I moved the parts I'd installed in it over the years to the new build, plus the wireless card that came with the Pavillion. Strangely, with the same drivers and setup, the card refuses to find any WiFi signals - not the one it was connected to prior to the move nor the other networks around the area. Changing the drivers, uninstalling the device, rebooting - nothing will work. The symptoms are exactly the same as when I moved the card to another slot on the Pavillion.
View 8 Replies View RelatedI have a TP link TD-W8901g modem router with 1 wan and 4 LAN. My questions is can i use this modem to receive wifi signals through wan and give out through lan. i currently use internet from telephone cable. But i have got a free hot spot near my home. Currently i Am using a pc without wireless card.
View 1 Replies View RelatedI need to have some (maybe four) virtual network interfaces, one face of them connected to my laptop and another face bridged to one of my physical network interfaces.How can i do that?Ive tried VirtNet and Microsoft Loopback Adapter but no success.
View 1 Replies View RelatedMy problem is that we moved house and had to wait for our new internet to be connected in the meantime I used my iphone to tether but now that we have our internet connection back my laptop won't work with wireless. It says it's connected and excellent strength but when I try to open a page it says Page Cannot be Displayed.I know it's not the router because our PC and PS3 is connecting fine, and I can connect to the internet on my laptop via a ethernet cable. My drivers are updated and when I run a check it says the device is working properly. The IP address is correct and I have the correct SSID and Network key. I don't know what else I can try. I have contacted my internet supplier and the ran through everything they they could think of and nothing worked.
View 3 Replies View Relatedmy laptop says not connected, no connections are available. Im thinking thats bizzare because we have wireless connection in our house it was on to and everyone elses computers are working even phones
View 2 Replies View Related