Is there any way to use an asa 5510 to detect which computer on the inside of my network is connecting to ip 87.255.51.229. I am being blacklisted for w win32/Zbot connection, I need to identify this computer and get it disconnected from the network ASAP.
View 6 RepliesThe Voip pbx resides on a seperate lan, not connected to the ASA. Users from behind the ASA (inside) try to connect to the VOIP pbx using a soft phone. The Voip connection is established, however users cannot here conversations on either end.Im assuming this is possibly a Sip and Pat issue? The ASA firewall is using a seperate Global IP for PAT. Also I have opened ports on the outside interface for SIP udp 8081, 2088,16000-16010 and 15000-15511. I have both SIP and H323 h225 inspection in place as well.
View 5 Replies View RelatedWe have an inside interface, 192.168.10.0/23We have an outside interface, public ip...We have the ASA connected to 5 site to sites, this is working fine and through the internal interface can access all remote sites and vice vera. These are 192.168.20.0/24, 192.168.30.0/24, 192.168.40.0/24, 192.168.50.0/24 and 192.168.60.0/24,When a user connects via Cisco VPN Client they can see the inside network but can't talk to the remote networks connected, for instance 192.168.40.0/24... whereas an internal user can. I understand that the VPN client connection is seen as an outside connection, not an inside connection... but then I read [URL] and I am confused even more.
View 8 Replies View RelatedI have a single 5510 ASA and a paired of 3750 Stacked Switches. I was trying to create an Ether channel on the ASA and connected to the SW Stack port channel to support different VLANs sub interfaced at the ASA. am confused with the following statement from doc. [URL].
Section Guidelines and Limitations :
"The ASA does not support connecting an Ether Channel to a switch stack. If the ASA Ether Channel is connected cross stack, and if the Master switch is powered down, then the Ether Channel connected to the remaining switch will not come up.
What "If the ASA Ether Channel is connected cross stack"? or better. Is it possible to use the ASA 8.4 Port-Channel to connect it to the 3750 ether channel stack?
I am attempting to install an asa 5510 at my hq. Our MPLS network is provided by our ISP and the routers are managed by them. They will be working with me to add the needed routes to the routers. Using version 8.4.1 That said, here is my challenge:
I am connecting the MPLS routers and WAAS device to my core switch(also performing inter-vlan routing) in VLAN 2. There are 3 connections needed for the mpls equipment and they are all in vlan 2 on my core switch. The firewall (ASA 5510 with security plus licensing) also has an interface (outside) in vlan 2.
e0/0
shutdown
no nameif
[Code]....
configuration guides or suggest TAC as they have been a bit inconsistent with this issue thus far. What am I missing because I cannot get to where inside interface of the firewall is pingable by the lan and the outside interface of the firewall is pingable by the lan.
I am migrating over from and old PIX to an ASA 5510. After configuring the new device everything else is functional (Internet) but users are unable to pass traffic when connected through the vpn, they are able to authenticate and I see their session connected on the ASDM but no data is passed..[code]
View 4 Replies View Relatedi acces internet on my pc using tata photon+ mobile broadband service,my problem is that i bought a ps3 and want to share internet connection with pc using ethernet cable via lan modem, for this i connected ps3 and pc using ethernet cable,i go to custom and wired setting of ps3 but my ps3 keep saying 'connect ethernet cable'.
View 7 Replies View RelatedMy laptop connected to internet with wifi, but it cannot use even my laptop detect connected, when i run trobleshooter it's show 'no valid IP address' even i already set up to automatically detect , restart my wifi router and unplug doesn't make any changes
View 14 Replies View Relatedwireless works on other household computer, but not the Sony Vaio
View 1 Replies View RelatedWhen I plug my ethernet cord into my Dell XPS laptop, Windows doesn't detect that I have a connection. I've tried another cord and it works (it's too short to use instead) and my roommate has tried my cord and it works fine on his computer.I've tried diagnosing the problem, disabling and enabling the Local Area Connection, but nothing seems to work.
View 9 Replies View RelatedWe currently have 1 PC and my laptop connected to the internet with 0 hassle. My father brought in his work computer last night and asked me if I could set it up. Only problem is I cannot for the life of me have it connect to the internet.
He has a PC with Win7, and when I search for a network it says there's no connections available. The PC is inches away from the modem. Also, our other two computers had no problem picking out the connection after a quick scan.
I started to lose hope when I ran an ethernet cable into the PC to see if I could get it to recognize the connection.
No luck. This is not a brand new computer, it's his work computer that before the move was operating just fine.
So I have a wireless router downstairs in my house that usually reaches around the whole house. However as of a couple days ago, whenever I am upstairs I only get limited connectivity. It still detects my router, but I an exclamation point and I can't connect to the internet. However when I am downstairs I have a connection that actually works. This applies to multiple laptops, computers, phones, etc.
View 1 Replies View RelatedMy fianc just reinstalled Windows XP Home Edition last night as his computer was virus-ridden and it was becoming impossible to use. It took a couple times for the computer to even pick up the Windows disc, but fourth time lucky and it was good to go. Once reinstalled we tried to get everything checked and download some anti-spyware etc, but it wouldn't pick up the router. The router is wireless, but connects to his computer via a cable. The router is a Netgear 54 MPBS Wireless Router, DG834G v3. We have been told that the computer should just automatically pick up the router, but the only way it will allow us to try and connect is via a dial up connection.
View 2 Replies View RelatedI tried 3 cables, and even one of them was new. So im sure the problem isn't the cables. For some reason, whenever I connect a ehternet cable to my computer, I cannot seem to get internet connection through it. Some days ago I installed this Wireless Lan device from a CD, that came with a sort of antenne I had to put on my computer. It works great, BUT its slow. Thats why i would like to go on internet with cable again. I remember one day to another that my computer didn't detect the cables anymore, what could be the problem?
View 7 Replies View RelatedComputer unable to detect wireless adapter
View 1 Replies View RelatedI am about to buy a Netbook from HP with windows 7 Starter.But a few days back when I tried to connect my friend's laptop to my network using WiFi ,it accessed the Internet but did not detect any other XP computers on the Network neither could I ping them nor could I access their shared folders.
2)And What is N Draft?? and how is it different from WiFi-N?
3)And can I set up Guest Network so that I can give the connected computers Internet access but no Shared Folder access..
we recently upgraded our home router and have been having trouble ever since. Our old router was a Netgear one, so we bought a newer netgear model. Since installing the new one we can not get my daughters laptop, an iPad and ipods to work on the wifi. My computer is wired into the router and works fine, it is just the wireless. All of these things worked perfectly using our old netgear wirelss modem and all of them can find the wireless network on their list of available networks, they all say that they are connected with a good signal, but when they try to browse the internet or check emails, it comes up saying not connected to the internet. We even bought a range extender because we thought the signal might not be strong enough between the new router and my daughters bedroom which are at opposite ends of the house and on different floors, but it made no difference and wasn't a problem before.
Anyway, the router we bought is a Netgear N150 wireless modem router DGN1000, the cables are plugged in to ports 1 and 4 ( there is only 1,2,3 and 4 to choose from). The extender is a Netgear universal range extender WN2000RPT
I have tried turning it all off and back on again, have uninstalled it and reinstalled it, but still nothing. Daughters laptop uses Vista and she has McAfee security. Exactly as it has always been and has worked fine using our old wireless router, just not this new one.
My EA6500 are not displaying all the connected network devices on in the GUI. How do i force this? Is it a bug? How can I make sure all my devices are showing in the GUI?
View 5 Replies View RelatedMy desktop failed to detect the local area network, but my laptop successfully detects that network. What may be the reason? Both the case, the green light is blinking (Means there is not problem with the cable/line ?). Is it a problem related to the network pin? The same desktop is successfully connecting through another line. So it means, it not an issue with desktop computer or it's configuration.
View 8 Replies View RelatedWe have been having a problem with one computer on our network unable to detect our network, or when it rarely does connect, it only has one bar and barely works.The files we attached are one of the times it could connect, when we finally caught it at the right time.We have a total of five computers/laptops on our network connected at different times. We recently updated the router and we've updated the drivers for the network adapter on the problem computer.Neither has worked.The computer was moved here a few months ago and because of condensation the graphics card was destroyed. We took it to a computer repair shop (which is how we found this out) and they installed a new graphics card. It hasn't worked since it got here.That computer was traditionally used for gaming (before it moved here) but if we can get into an online game, our ping is really high, in the 100s.
View 8 Replies View RelatedSo lately my computer's wireless network has started to get really bad, we have 100mbit, and it only gets about 0.3. This seems to be an issue with the range, or something, since if i move the computer right next to the router, it runs at about 50-60mbit. Now a few days ago i decided to get an ethernet cable to try and solve the issue, but my computer doesn't detect a LAN connection, only the wireless one ( atleast it doesnt show up among the other connections). Some weeks ago the wireless connection worked nicely, but now suddenly it doesnt anymore. Currently i'm typing this from an old mac computer, since my internet doesn't work at all on my pc.
View 11 Replies View RelatedComputer keeps saying that the I need to plug in a ethernet cable but I already did. This is happening on my Windows 7 Ultimate partition. I also have have a Mac OSX partition and the internet is working fine on that partition.Here is what I get for ipconfig/all command:[CODE]
View 18 Replies View RelatedI tried connecting someone else's laptop to a network cable but the laptop refused to detect the hardware device plugged?
View 1 Replies View RelatedI no longer have a software disc, but setup via the 192.168.1.1 page has worked out fine...until the last reset. After the last reset/reboot of the wifi, I was unable to set up the wifi beyond use with my laptop. This is, no doubt, user error.WRT320N.No hard wire, wifi is connected to the cable modem. Everything in the house was on the wireless.
Issue: Laptop finds and connects to wifi just fine, password works just fine.iPhone cannot even detect the wifi in the house (but finds every other wifi in the neighborhood)iPad cannot detect the wifi in the house (but finds every other wifi in the neighborhood)Desktop cannot detect the wifi in the house (but finds every other wifi in the neighborhood)What do I need to tweek in the admin page 192.168.1.1 to allow other computers to jack into my wifi?
I have the WMP54G internal wireless adaptor. It normally works fine, but I have been having problems with it lately when I turn my computer back on from sleep. Even thought the wireless router works just fine, when the computer wakes up from sleep the adaptor does not seem to detect any network. I have to restart my computer, and then the adaptor detects the network.
View 1 Replies View RelatedI recently upgraded my computer (not laptop) from Windows XP to Windows 7-32 bit. I redownloaded and installed Network Magic, Linksys Wireless Manager and my WUSB600N adapter properly (I hope). Now everything was working fine, I was able to get onto my network through the adapter but today I noticed that the Linksys Wireless Manager seemed to not connect to my network, instead my computer some how did it without the wireless manager. Now when I tried to connect to a network through the Wireless Manager it said Error: 211 and said My Adapter may not be installed properly and told me to remove the adapter and attach it back after 20 seconds. I tried that but again my computer connected to the network STILL through the computers own manager not through the Linksys Wireless Manager. That was still saying Error 211. So the problem really is that the Linksys Wireless Manager wont detect my adapter but my computer is still able to detect it and connect to my network.
View 4 Replies View RelatedMy roommate and I are trying to set up the internet, but my computer won't detect the Ethernet Cable. Whenever I go to Network and Sharing Center and try connecting to the internet, the computer simply says "Windows did not detect any networking hardware", even though the light is clearly on and should be working. The cable is also new so it should be fine. I've also been looking around on the internet a bit, and in trying to fix the problem it looks like some of my Services are turned off, which seems to be causing the problem. However, whenever I try and turn them on, I get an error message saying "The dependency service or group failed to start".
View 5 Replies View RelatedHave tried resetting my DNS and have checked my firewalls, I do not know what is going on. I do not have another comp to copy and paste my info from the cmd. Ive also gone into settings and made sure it is automatically picking up the dns. When i go onto my google chrome is says my dns look up failed.
View 19 Replies View RelatedOne computer does not see the other through pinging...but somehow we are connected...strange i know. My confusion ( being network illerate ) is with the names and etc. and some terminologies ie ..client? host? I have found in the past when someone triesthey use words or areas that do not coincide with my system...which is laptop with win 7 prem and desktop XP sp3
View 2 Replies View Relatedscanner is not connected to the computer but printer is
View 1 Replies View RelatedI recently purchased a build computer. Now I can not connect to the internet. It is not reconigizing the connection.
View 2 Replies View RelatedI have a desktop and a laptop that are connected to my router but can't connect to the internet. One of our other desktops is working great. Another had the same issue and I fixed it using the "netsh int ip reset c:
[code]....
My computer keeps connecting and disconnecting from the internet- other computers on the network aren't doing this- i also manually put in an IP address and that didn't work either, whats going on?
View 5 Replies View Related