I have a modem DPQ3212. Downstream led is in amber. Link led is in amber, flashing. My ISP tell me all is OK, but my internet is slow. I need all leds in green. Only one downstream channel is open.
View 1 Replies
I have a new Cisco DPC 3010 modem and the link light keeps turning a amber color. When the light goes from green to amber my download speed drops from 12m to 8m and my upload goes from 2m to 312k. I cant find anything on what the light turning amber means. Also cant find out how to log into the modem.
View 0 Replies View RelatedA couple nights ago, in the middle of my surfing the net, i was cut off and 'checked the modem (working good) and the router, displaying blinking amber lights --modem and internet. I had to restart my router, usually, it would work after that and i could surf again. This time, when it started back up, the router light turned blue and then the modem and internet light started blinking amber. I haven't done anything except chat over the net when it happened. All other lights are blue. I have cycled the modem power, the router power, and restarted the computer and have the same results. I already followed the troubleshooting from Belkin support 192.168... completely restore it to it's factory settings and yet, i still end up not being able to connect in the internet and with that blinking amber lights. I already tried connecting directly from my modem to my win 7 laptop --no problem at all. I could surf and chat. but when i tried connecting it again from modem to router so i can do wireless.
View 4 Replies View RelatedWe just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies View RelatedBelkin F5D8236-4 v1 The Internet flashes amber and goes back to solid blue. It will stay blue on average for up to five minutes (this is not exact times) but on average it happens every five minutes. This is a constant issue. I've contacted my ISP (Comcast) and they said all looks fine on their end. My signals to them are just fine.
Sure, I can bypass the router all together, but my modem will NOT allow me to see any logs to know the issue is happening on their end. I'm feeling a bit confident its a router issue though.
I've reset both Modem and Router. I've made sure my connection was set to Dynamic. My router/security log does not offer up anything at the times this happens, but I do see several listings for "sending OFFER to a local IP of one of our laptops, but this does not match the times the router net light goes amber.
Yes, when the amber light is flashing on the globe/internet icon, I can still access my router page, but it does say DISCONNECTED. It will eventually go back to connected in a few minutes. This router is not very old and I've always praised Belkin routers, so crossing fingers my router is okay, times are tough for so many of us.
What do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router
View 2 Replies View RelatedMake and Model Cisco DPQ3212 (Modem)Netgear N600 Wireless Dual Band Gigabit (Router)So when I first got the router and modem and hooked it all up everything worked. Then the inter got shut off for a day then came back on and now the only way I can use it is by Ethernet cord. This would be fine but, unfortunately the Xbox in in the living room nowhere near the router. I have tried power resets and everything else the companies of both tell you to try but nothing is working.
View 8 Replies View RelatedFor about 3 minutes the 2.4GHz and 5GHz LEDs began to flash in sequence, [2.4-5-2.4-5-2.4-5-Both-Both], it just kept doing that. During that time wireless connections were unresponsive. When they went back to normal I checked the router and it didn't reboot or anything. This is the first anomaly I've ran into running the 2.05NA FW.
View 6 Replies View Relatedjust installed 6 new APs to a client remote site off a 5508 controller. 5508 is running 7.0.116 total of 78 installed APs, mostly 1142's with a dozen or so1242s. All going perfectly until I was about to leave site and noticed two of the APs had no LEDs lit. Checked in the controller, as I had renamed them so knew they were on the system, and they are both there. Connected to each of them and was successful and everything seemed ok - no blue LED though. Rebooted them and the LEDs work as expected during the boot process but as soon as they have entered normal operation the LEDs go dark. urls....but no reports of it with anything other than 3502's.Change process is galacial and heavily monitored so dont want to invoke it if it wont address the concern.
View 10 Replies View RelatedIs it normal for an E1000's LEDs to get dim after a few years??Because my LAN port #1 and #2 are dim, as well as the power LED.I'm guessing it's just because they are always on?
View 5 Replies View RelatedMy Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies View Relatedafter a recovery of a main power failure the RPS LED on my Cisco 2960 is blinking amber. The command sh env power on the Switch tells me: POWER is faulty. sh env rps says: RPS is supplying.
On the RPS2300 the DC output LED is blinking green. Due to the manual this means: The RPS 2300 is backing up the connected device.
So far so true. The RPS has backed up for the time the main power supply was down.
But actually both, the Powersupply from the RPS and the main power are available.
But the Switch didn't switch back to it's bultin powersupply, so still the RPS ist suppling the switch.
What can we do to get the Cisco 2960 into the correct state? Is there a special command which i can use?
I was trying to connect Ethernet cable to my laptop LAN port, there was solid Green on my Hub and there was no light on my laptop LAN. I have swapped with a none good working computer and Ethernet cable everything works fine.I felt the problems is the physical LAN port on my laptop.
View 1 Replies View RelatedI have a WLC 5508, its PS1 and PS2 are OFF state, SYS is blinking amber and ALM is continues amber, Its port s are not coming UP and I am not able to access the Controller, All ports are physically down and in console nothing is showing when I connect through the console cable.
View 2 Replies View RelatedWe are having Cisco 7206VXR with NPEG2 and the IOS c7200p-spservicesk9-mz.124-15.T10.bin.,PA-MC-STM-1SMI is connected to 3rd Slot of the Chassis. The Links terminated on the SMI are working fine and we are not getting any Error Messages on Chassis regarding the this SMI.
But here we have Amber LED Glowing on ALARM LED of the SMI Card.
As per the below Link: URL
This means Loss of Signal/Frame.
##Table 1-5 PA-MC-STM-1 LEDs
#LED Label
#Color
#State
[Code]....
I have a PS3 connected to a Gig port on my 3560. When I boot-up the PS3 I have to wait around 30 seconds for it to get DHCP.
I noticed the orange LED would stay on and go green after 30 seconds. I assumed I would have an error-state but I do not, the port show connected with no errors even though it's orange. I have no connectivity from the ps3 until the light goes green and then all is well. The port is access and I have manually configured duplex and speed.
Switch>show version
Cisco IOS Software, C3560C Software (C3560c405ex-UNIVERSALK9-M), Version 12.2(55)EX3, RELEASE SOFTWARE (fc2)
[Code].....
We have one Cisco ACE in our data center which is working fine but has Amber light on front & Rear.
I read the document & it shows that either it is a system fault or internal fan failure.
I am sure it is a fan failure because if there was any system fault then ACE dont work properly. should we replace the hardware?
unfortunatley we dont have support contract & i am working to get it one.
everything was all good, my brother went crazy and unplugged everything.it effects our house phone too, that could be the problem.i just dont know what wires went where. all the wires are the same color.but i know which is which. just again, dont know where.i would like to get it done before he gets home later on.
View 1 Replies View RelatedI have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies View RelatedWe have one cisco core switch 6500 series which was configured portchannel on several gig interfaces. This port is used as a trunk to enable communication between VLANs. The VLANs is where several high-end servers/hosts reside.After we disable / unbind the portchannel, the port turns amber. The following is what we did on the interface
1-no switchport command
2- make the port as access mode #switchport mode access
3- shut and no shut
4- clear arp
5- clear mac
what else can we do on that particular interface. It is just on that particular interface, the rest are ok.
I am replacing an old Catalyst 3550 (that has 2 Gig ports) with a 3750 (that has 4)- I used the exact same configuration in the new switch. When I plugged in the new 3750, the trunk ports started blinking from green to amber. I dont know why this is occuring- it SEEMS to be fine, but we havent thrown a whole bunch of traffic over it.
View 4 Replies View RelatedI am currently supporting an engineer onsite remotely and have come across a strange problem . I have installed a few controllers but none of them have behaved in this manner. The model is a WLC 5508-50k9 model wireless controller and software 7.0.98.0, I have seen as per installation guideline that amber means th following
Distribution ports 1-8 Off: Not present.
#Green: Indicates SFP port is active and link is established.
#Amber: Present with failure
This mean that so coherent fault lies as follows on Layer 1&2 . The switch port light does not go green either. We have used both xover and straight but no luck
I have a Problem with a ASA 5505 when i power on the ASA the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.
View 9 Replies View RelatedI have a Cisco catalyst switch 3750G has all LED lights staying amber still without blinking, I cannot console into it and it can’t boot past the POST.
THE ISSUE HAPPENED ON THE NETWORK AND IT WAS ISOLATED FROM THE NETWORK, SO NOW I AM TRYING TO RESOLVE IT OUTSIDE THE NETWORK
Command to check system status of ACE 4710 appliace? For example if fan is OK or CPU temperature, or other HW things what could be faulty?
For example now I have system ID button blinking amber bot do not know what is wrong. I just know that there is some faulty.I just used show tech-support command and it does not seems that it include some HW statistics.
I want to switch back to my dell desktop 4600, it is not reading the network or ethernet there is a steady amber light. I clean inside and pulled network card out and put back in and still have steady amber light. I have dsl with att and it works on my laptop.
View 5 Replies View RelatedI have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?
View 2 Replies View RelatedI have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct.
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green?
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?
I have a Linksys X2000 modem. Sometimes I see the "Wi-Fi Protected Setup" button glowing orange (amber?) for no apparent reason. The manual says that it "blinks rapidly in amber if an error occurs" but I don't think any device is trying to connect wirelessly at the time. How can I determine if there is a problem?
View 5 Replies View RelatedIn my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
View 4 Replies View RelatedIn our company 3nos Cisco 3750 (WS-C3750-48P) access switch in stake mode. All port are assigned with voice and data Vlan also Avaya IP connected with this switches. From last few days tow port 2/0/7 and 2/0/8 is showing amber and status is showing err-disable. At Avaya end it is showing a message “ETHERNET WAITING” in phone dispaly. I try to connect laptop directly with these ports but it is showing "Cross Connectivity". [code]
View 4 Replies View RelatedI have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.
View 3 Replies View Relatedour house have a lot of rooms and think walls and the router set up in my room is giving only 2 signal bars in other parts of the house. i already have 2 routers and planning to place the 2nd router in the living room using a long cord. can i use 2 routers in one modem?
View 1 Replies View Related
