Cisco WAN :: 2960 - RPS LED Is Blinking Amber

Jul 26, 2011

after a recovery of a main power failure the RPS LED on my Cisco 2960 is blinking amber. The command sh env power on the Switch tells me: POWER is faulty. sh env rps says: RPS is supplying.
 
On the RPS2300 the DC output LED is blinking green. Due to the manual this means: The RPS 2300 is backing up the connected device.
 
So far so true. The RPS has backed up for the time the main power supply was down.
But actually both, the Powersupply from the RPS and the main power are available.
But the Switch didn't switch back to it's bultin powersupply, so still the RPS ist suppling the switch.
 
What can we do to get the Cisco 2960 into the correct state? Is there a special command which i can use?

View 5 Replies


ADVERTISEMENT

Cisco Wireless :: WLC 5508 Sys Is Blinking Amber

Jul 22, 2012

I have a WLC 5508, its PS1 and PS2 are OFF state, SYS is blinking amber and ALM is continues amber, Its port s are not coming UP and I am not able to access the Controller, All ports are physically down and in console nothing is showing when I connect through the console cable.

View 2 Replies View Related

Cisco WAN :: 3550 - Blinking Green / Amber Lights On Ports?

Jul 11, 2011

I am replacing an old Catalyst 3550 (that has 2 Gig ports) with a 3750 (that has 4)- I used the exact same configuration in the new switch.  When I plugged in the new 3750, the trunk ports started blinking from green to amber.  I dont know why this is occuring- it SEEMS to be fine, but we havent thrown a whole bunch of traffic over it. 

View 4 Replies View Related

Cisco Application :: ACE 4710 - System ID Button Blinking Amber

Apr 17, 2013

Command to check system status of ACE 4710 appliace? For example if fan is OK or CPU temperature, or other HW things what could be faulty?
 
For example now I have system ID button blinking amber bot do not know what is wrong. I just know that there is some faulty.I just used show tech-support command and it does not seems that it include some HW statistics.

View 4 Replies View Related

Belkin Router F5D82354 - Modem And Internet Blinking Amber

Nov 2, 2011

A couple nights ago, in the middle of my surfing the net, i was cut off and 'checked the modem (working good) and the router, displaying blinking amber lights --modem and internet. I had to restart my router, usually, it would work after that and i could surf again. This time, when it started back up, the router light turned blue and then the modem and internet light started blinking amber. I haven't done anything except chat over the net when it happened. All other lights are blue. I have cycled the modem power, the router power, and restarted the computer and have the same results. I already followed the troubleshooting from Belkin support 192.168... completely restore it to it's factory settings and yet, i still end up not being able to connect in the internet and with that blinking amber lights. I already tried connecting directly from my modem to my win 7 laptop --no problem at all. I could surf and chat. but when i tried connecting it again from modem to router so i can do wireless.

View 4 Replies View Related

No Amber Light On Laptop LAN

Jan 31, 2011

I was trying to connect Ethernet cable to my laptop LAN port, there was solid Green on my Hub and there was no light on my laptop LAN. I have swapped with a none good working computer and Ethernet cable everything works fine.I felt the problems is the physical LAN port on my laptop.

View 1 Replies View Related

Cisco WAN :: DPC 3010 Modem Amber Color LED

Jan 21, 2011

I have a new Cisco DPC 3010 modem and the link light keeps turning a amber color. When the light goes from green to amber my download speed drops from 12m to 8m and my upload goes from 2m to 312k. I cant find anything on what the light turning amber means. Also cant find out how to log into the modem.

View 0 Replies View Related

Cisco WAN :: 7206VXR - SMI Card Alarm LED Remains Amber

Aug 25, 2011

We are having Cisco 7206VXR with NPEG2 and the IOS c7200p-spservicesk9-mz.124-15.T10.bin.,PA-MC-STM-1SMI is connected to 3rd Slot of the Chassis. The Links terminated on the SMI are working fine and we are not getting any Error Messages on Chassis regarding the this SMI.
 
But here we have Amber LED Glowing on ALARM LED of the SMI Card.
 
As per the below Link: URL 
This means Loss of Signal/Frame.
##Table 1-5     PA-MC-STM-1 LEDs
#LED Label
#Color
#State
[Code]....

View 2 Replies View Related

Cisco Switching/Routing :: 3560C Amber LED But No Error

Mar 22, 2013

I have a PS3 connected to a Gig port on my 3560. When I boot-up the PS3 I have to wait around 30 seconds for it to get DHCP.
I noticed the orange LED would stay on and go green after 30 seconds. I assumed I would have an error-state but I do not, the port show connected with no errors even though it's orange. I have no connectivity from the ps3 until the light goes green and then all is well. The port is access and I have manually configured duplex and speed.
 
Switch>show version
Cisco IOS Software, C3560C Software (C3560c405ex-UNIVERSALK9-M), Version 12.2(55)EX3, RELEASE SOFTWARE (fc2)

[Code].....

View 5 Replies View Related

Cisco Application :: 4710 ACE Hardware (Amber Light)

Oct 30, 2011

We have one Cisco ACE in our data center which is working fine but has Amber light on front & Rear.
 
I read the document & it shows that either it is a system fault or internal fan failure.
 
I am sure it is a fan failure because if there was any system fault then ACE dont work properly. should we replace the hardware?
 
unfortunatley we dont have support contract & i am working to get it one.

View 1 Replies View Related

Cisco Routers :: Leds Amber In DPQ3212 Modem

Oct 11, 2012

I have a modem DPQ3212. Downstream led is in amber. Link led is in amber, flashing. My ISP tell me all is OK, but my internet is slow. I need all leds in green. Only one downstream channel is open.

View 1 Replies View Related

D-Link DIR-615 :: Power Light Goes Amber And Nothing Works

Mar 24, 2013

I have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).

View 3 Replies View Related

Cisco WAN :: 6500 Port Turns Amber After Unbind Channel

Sep 12, 2012

We have one cisco core switch 6500 series which was configured portchannel on several gig interfaces. This port is used as a trunk to enable communication between VLANs. The VLANs is where several high-end servers/hosts reside.After we disable / unbind the portchannel, the port turns amber. The following is what we did on the interface
 
1-no switchport command
 
2- make the port as access mode #switchport mode access
 
3- shut and no shut
 
4- clear arp
 
5- clear mac
 
what else can we do on that particular interface. It is just on that particular interface, the rest are ok.

View 7 Replies View Related

Cisco Wireless :: 5598 - New Installation / LED Stuck In Amber Mode

Oct 9, 2011

I am currently supporting an engineer onsite remotely  and have come across a strange problem . I have installed a few controllers but none of them have behaved in this manner. The  model is a WLC  5508-50k9 model wireless controller and software 7.0.98.0, I  have seen as per installation guideline that  amber means th following
 
Distribution ports 1-8 Off: Not present.
#Green: Indicates SFP port is active and link is established.
#Amber: Present with failure
 
This mean that so coherent fault lies as follows on Layer 1&2 . The switch port light does not go green either. We have used both xover and straight but no luck

View 3 Replies View Related

Cisco Firewall :: Solid Amber Status Light On ASA 5505?

Apr 14, 2010

I have a Problem with a ASA 5505 when i power on the ASA  the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.

View 9 Replies View Related

Cisco Switching/Routing :: 3750G - LED Lights Stay Amber

May 8, 2012

I have a Cisco catalyst switch 3750G has all LED lights staying amber still without blinking, I cannot console into it and it can’t boot past the POST.
 
THE ISSUE HAPPENED ON THE NETWORK AND IT WAS ISOLATED FROM THE NETWORK, SO NOW I AM TRYING TO RESOLVE IT OUTSIDE THE NETWORK

View 3 Replies View Related

Dell :: 4600 Ethernet There Is Steady Amber Light

Nov 24, 2012

 I want to switch back to my dell desktop 4600, it is not reading the network or ethernet there is a steady amber light.  I clean inside and pulled network card out and put back in and still have steady amber light. I have dsl with att and it works on my laptop.

View 5 Replies View Related

Cisco Firewall :: Solid Amber Status Light On ASA 5505 Under SmartNet

Oct 14, 2011

I have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?

View 2 Replies View Related

Cisco Switching/Routing :: 6509 Amber System Light On Both SUP32

Feb 20, 2012

I have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
 
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct. 
 
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green? 
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?

View 5 Replies View Related

Linksys Cable / DSL :: X2000 / Amber Light On Setup Button?

May 4, 2013

I have a Linksys X2000 modem.  Sometimes I see the "Wi-Fi Protected Setup" button glowing orange (amber?) for no apparent reason.  The manual says that it "blinks rapidly in amber if an error occurs" but I don't think any device is trying to connect wirelessly at the time.  How can I determine if there is a problem?

View 5 Replies View Related

Belkin Routers :: Flashing Amber Light On N300 Router?

Nov 25, 2012

We just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.

View 2 Replies View Related

Belkin Routers :: F5D8236-4 V1 Internet Icon Flashes Amber

Dec 12, 2012

Belkin F5D8236-4 v1 The Internet flashes amber and goes back to solid blue. It will stay blue on average for up to five minutes (this is not exact times) but on average it happens every five minutes. This is a constant issue. I've contacted my ISP (Comcast) and they said all looks fine on their end. My signals to them are just fine.

Sure, I can bypass the router all together, but my modem will NOT allow me to see any logs to know the issue is happening on their end. I'm feeling a bit confident its a router issue though.

I've reset both Modem and Router. I've made sure my connection was set to Dynamic. My router/security log does not offer up anything at the times this happens, but I do see several listings for "sending OFFER to a local IP of one of our laptops, but this does not match the times the router net light goes amber.

Yes, when the amber light is flashing on the globe/internet icon, I can still access my router page, but it does say DISCONNECTED. It will eventually go back to connected in a few minutes. This router is not very old and I've always praised Belkin routers, so crossing fingers my router is okay, times are tough for so many of us.

View 9 Replies View Related

Belkin Routers :: Light Stays Amber Even After Reset N300

Apr 25, 2013

What do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router

View 2 Replies View Related

Cisco Switching/Routing :: 3750 (WS-C3750-48P ) Two Port Showing Err-disable And Amber

May 10, 2013

In our company 3nos Cisco 3750 (WS-C3750-48P) access switch in stake mode. All port are assigned with voice and data Vlan also Avaya IP connected with this switches. From last few days tow port 2/0/7 and 2/0/8 is showing amber and status is showing err-disable. At Avaya end it is showing a message “ETHERNET WAITING” in phone dispaly. I try to connect laptop directly with these ports but it is showing "Cross Connectivity". [code]

View 4 Replies View Related

Cabling / Cards :: Belkin Connect N150 Router Has Solid Amber Light?

Oct 16, 2011

I have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.

View 3 Replies View Related

Cisco Switching/Routing :: Add 2960 To Stack Of 4 X 2960 Switches

Feb 7, 2012

I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.

View 12 Replies View Related

Cisco Switching/Routing :: 2960-S To 2960-LST Configuration Over Fiber?

Feb 11, 2013

I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber.  The link is up on the LST but will not come up on the -S.  What command should I use to bring up this link?  I have tried no shut from the (Config-if)# prompt.         

View 3 Replies View Related

Cisco WAN :: 1131 - LED Blinking Red And Off

Sep 28, 2011

I have the 1131 hardware manual and it is stating that this is caused by a boot loader issue or the AP did not get the IOS file from the controller. We have a Cisco 4404 controller that this AP reports to. It was one out of 30 and after a reboot it is working fine. What can i do in the future to catch this and prevent this from happening.

View 1 Replies View Related

Router's LAN Is Not Blinking

Sep 4, 2011

My router's LAN is not blinking and also my internet is not working!!

View 1 Replies View Related

Cisco Wireless :: AIR AP1131AGE K9 R Led Is Blinking With Red

Mar 22, 2012

My aironet AIR-AP1131AG-E-K9. has 2 small LED, which is E and R , This R led is blinking with red color, I want to know what does it mean.

View 4 Replies View Related

Cisco Firewall :: PoE Blinking On ASA 5505

May 16, 2013

I have a 5505 firewall deployed in a home office with two 7941 telephones behind it.  The phones pull PoE from the ASA.  The firewall was deployed a couple weeks ago, and everything worked great for about 2 days.  (This configuration has been working for a couple years, but I just upgraded the 5505 to a new one with more RAM so I could run 8.3 and higher.)  Then the phones lost power from the ASA and they now "blink" about every 3 seconds.  They go on, off, wait three seconds, then go on, off, wait three seconds, etc.
 
I was not able to solve the problem by shutting and no shutting the ports, and there is little-to-nothing that you can do from the CLI to configure the PoE.  I changed software versions for troubleshooting, but the problem persists. A reboot fixes the problem for a couple days. Then, the problem reoccurs.
 
A "show power inline" yields the following when everything is working.
 
Home5505# sho power inline
Interface   Power   Device
---------   -----   ------
Et0/0        n/a    n/a

[Code].....

View 1 Replies View Related

Cisco Switches :: Broken SG 200-08p Switch - Blinking LED?

Aug 21, 2011

I turned unplugged it and plugged it back in.  Now its blinking green power LED.  Is it dead?

View 2 Replies View Related

Router :: Dlink Dir-628 Logo Is Blinking?

Dec 29, 2011

i have a dlink dir-628 and it not working problem. the power light, local network led and even the dlink logo is blinking. it was working fine yesterday but it just stopped working randomly, i tried to reset but that doesnt even work,

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved