I need a tool simulator or emulator for my work, because before a change first i would have to configure in tool and before I configure in the production environment, I have 4506 e-series, catalyst 2760, catalyst 2960 and We need a simulator or emulator that can me configure whit those devices.
View 5 RepliesToday I went to an Extreme Networks training session and they discussed a plugin for the switch that emulates IOS. I'm not sure how in depth it gets and if it stays current with the commands in the latest IOS release, but it did the normal commands such as conf t and sh vlan, etc.
View 5 Replies View RelatedNice for those who want to see what it looks like:
Cisco Connect Cloud: [URL] EA6500: [URL] . And of course all other Linksys devices: [URL]
I have developing a utility which lets a user do the following :-
1)Identify the internet gateway device / router using uPnP
2)Check for the portmappings present in the gateway
3)Add / remove a port mapping from the gateway device
4)some other functions like loopback interface testing etc
Now , I need a router simulator (or any other way )which supports the following to test my work uPnP+ NAT +can be configured using SOAP XML messages although this is not a requisite as I am using Microsoft's SDK for uPnP ?Host 3 (or may be 4 is the RAM allows) virtual machines , connect them into a subnetwork using this software and then testing for the above requirements .
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedI am trying to configure below commands in Cisco 4506 E with SUP 6 LE but these commands are not not supporting in the switch.Even QOS command is not taking in the siwtch....This was working fine in Cisco 4500 with SUP 2..not i upgared to 4506 E with Sup 6 LE.
qos dblqos map dscp 0 to tx-queue 2qos map dscp 16 18 20 22 24 26 28 30 to tx-queue 4qos map dscp 34 36 38 to tx-queue 4qos map cos 3 to dscp 26 qos map cos 5 to dscp 46 qos
We have a Cisco 4506 with Supervisor 6-E. We plan on replacing the existing 4 line cards with
WS-X4548-GB-RJ45V
I need to configure DSL Load Balancing on Core Cisco Switch 4506-E. I have a Router Cisco 2811 with 2GE Ports and a Firewall Cisco ASA5505. I have 8 Physical DSL Connections with 1Mb each. I need to combine that 8 Mb on Core Switch and allow each end user to access the Internet via the available DSL connection which means that every user has 8 Mb available.
View 7 Replies View RelatedI m a Network engineer in company, we have around 800 users in the office.Below is the details of my network infra.We have 4506 chasis with IOS version of 12.4 (44r) SG3HSRP is configured for redundancy.HSRP is configured on VLAN besis
The problem that HSRP is not working working properly, When my active VLAN goes down, Standby VLAN act as a Active VLAN but traffice is fail to route trought that VLAN and i m not able to ping another vlan from that VALN.
I am in the process to route two buildings together. Both building have the same network setup. 2 Core Switches 4506-E Chassis having glbp for layer 3 redundency on about 20 vlan in each building with default intervlan routing in place.Below is a simple sketch of how these are connected. Blue lines are still not connected...
What I need is to setup routing onto the blue fibre links so that networks from building 1 can reach networks on building to and vias versa. I would also need to implement some sort of redundency since I have to fibre links between the 2 building.
I have CNA 5.5 and have upgraded our 4506 with sup. v4 to cat4500-entservicesk9-mz.150-2.SG.bin (latest version). CNA shows the 4506 as an usupported device.
View 4 Replies View RelatedI have a problem about user tracking for LMS 4.0.
For example:Switch 4506 send the endhosts for every VLAN that it has configured, except for one, but I can see that VLAN is configured over the switch.
are there problems directly with the connected endhosts over this VLAN or is it a problem about configuration for user tracking settings ?
Does WS-X4448-GB-SFP line card be used in 4506 Chassis
View 2 Replies View RelatedI want to sizing a CAT 4506 with WS-X45-SUP7L-E supervisor. To support full routing (EIGRP and BGP) I have to choice CAT4500E IOS ENTERPRISE SERVICES W/O CRYPTO.
View 2 Replies View RelatedI have a Cisco 4506 With IOS 12.2 54SG1
Iam new on Acs 4.2 and i want to use Certificates to authenticate my windows XP Client and Igels.
On Windows Xp i selected : IEEE 802.1X Authentication enable EAP (Peap)
But i dont understand the Certification of ACS 4.2.
I generated a Self-Signed Certificate. Is this right ? and under installed Certificates the Certificate Status is okay.
Do i have to create for each windows Machine one user Account under user-Setup to authenticate the Machine?
Where do Windows Xp know whitch Certificate he have to take ?
I configures the Switch on Global Configuration like this:
aaa authentication login default group tacacs+ enable
aaa authentication enable default group tacacs+ enable
[Code].....
Iam triying to configure ist szenario till 4 days and it still dont work.. On Windows i Only get the Error" authentication failed" on the Switch the same : dot1x : Authfailed
I am getting High CPU utilization in one of my switch which has many layer 3 vlan interface and many other routing interface.In the o/p of show process cpu i get 64 % CPU utilization. The o/p is as below
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
30 37656252881151776906 3269 62.31% 63.95% 64.82% 0 Mgmt LoPri
And rest of the other process are very normal. Only cat4k Mgmt LoPri is consuming very high cpu utilization. I have checked all the interface input queue and all are very normal.
I just started a new Position and they have CATos still runing on some of there 4506 and 6509 switches. I amy trying to come up with a plan to upgrade the switches to IOS but I dont know if they will take it or not. I know I need to get flash Cards to hold the IOS but i need to make sure that I get the right IOS for the Switches.
View 1 Replies View RelatedMy existing 4006 chassis is using Supervisor III (WS-X4014). I have another 4506 chassis using Supervisor IV (WS-X4515) and a Net flow Services Card (WS-F4531) build on top of it.
I need Net flow Services Card in 4006, so can I just replace the Supervisor IV (WS-X4515) used in Cisco 4006? Is it compatible with 4006?
I have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedI am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies View RelatedWe have sup engine 6L(WS-X45-SUP6L-E) on two 4506 switch. both switches connected in LAN (HSRP primary and Secondary).
We are going to replace it with Sup7LE. What is the best procedure to get this done with minimal outage?Any other important thing to be noted ? Note : We have Lincence for SUP 7LE
We are attempting to PXE boot from clients obtaining their DHCP lease information from DHCP pools configured on our 4506. The PXE server, and the client are configured in separate VLANs. We have configured option 66 to point to the PXE server IP address, and the bootfile option to point to the PXE boot configuration filename. On the client side SVI, we also have configured the ip helper-address command to point to the PXE server (which also acts as another DHCP server for redundancy).
The PXE boot continuously fails stating it is unable to find the configuration file. If we remove the DHCP pool from the 4506, and allow the client to receive their DHCP lease info from the secondary server (Windows 2k8 - same server as PXE server), they PXE boot with no issues.
We have no problem obtaining DHCP info, just completion of the PXE process.
Does SUP 7E is comatible with IOS? It came with IOS-XE preloaded and there are no IOS software listed under downloads.
View 3 Replies View RelatedYesterday I've faced a Problem that is not letting me boot with the new IOS.
Actually I'm planning upgrade IOS which supports SSH. As part of plan I've downloaded the new IOS image and uploaded via TFTP server to the switch.
After uploading to the switch. I've verified image and MD5 hash also. Everthing is fine. Then after I set the boot variable for the newly uploaded Image.
When I'm rebooting the Device it is not taking the new IOS. It's booting with the OLD image. Even It's not showing any error message while rebooting (ACTIVITY FILE ATTACHED FOR YOUR REFERENCE) I can't take risk by deleting the old IOS.
i have cisco catalyst 4506 switch and i run no logging by mistake and i am trying to enable logging again but not displayed at all
View 7 Replies View RelatedI have 4506 with below sup, my requirement is to enable netfolw , but as i came to know that it is not supported in this sup, is there any additional option which can be explored to get the netflow working without replacing sup.
Card Type Model
-------------------------------------------------------------+-----------------------
Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
we have a cissco 4506-e switch with ios version 03.02.05.SG . We ae currently facing a strange problem . Vlan interfaces configured in he switch are not showing input and output traffic, whereas the traffic is seen on the Gig interfaces mapped to the respective vlans . We also tried configuring the load-interval 30 , but there is no change . Interace 3/5 is mapped to vlan 5 . For this issue we have also done the IOS upgrade from 3.1.1SG to 3.2.5SG recently still the issue is same. [code]
View 2 Replies View RelatedWe have just purchased and installed a 4506-E chassis. It contains a supervisor, two POE blades and 3 non-poe blades. Version is 12.2(53)SG1. Anyhoo, one of the ports isn't providing power to an IP phone. We can plug the phone into any of the other POE ports and it works fine. Is there a way to test an idividual port for POE problems? What could the problem be? The port works for normal data but will not provide power.
View 12 Replies View Related