I am currently using a Cisco 1751 w/ 1-WIC-DUS-T1 to connect our branch locations via Frame Relay. I will be adding 2 new locations in about 2 months. What is the 1800 series match for the router I currently use and is there and performance advantages?
View 2 Repliesit's possible to use the Cisco 1751 router without any add WIC , just use the build in Ethernet port behind Linksys or other ADSL router given from ISP, and configure the Cisco 1751 to make and handiling the VPN traffic ?if yes , how can I configure the Ethernet0/0 port ?
View 9 Replies View RelatedI do not have a cross over cable and have to use xmodem. I set the baud rate to 115200 and I can see everything fine. Using Tera Term when you send the file via xmodem it freezes and closes on packet #3 or about 384 bits. When simply clicking the send file button you get the error-
*** Reserved LVL 7 Interrupt ***
PC = 0xfff0bc98, Vector = 0x500, SP = 0x80004c4c
Not sure what to do from here. I have tried everything.Error you get when you boot the router:
System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)
TAC Support: [URL]
Copyright (c) 2001 by cisco Systems, Inc.
C1700 platform with 32768 Kbytes of main memory
loadprog: bad file magic number: 0x0
boot: cannot load "flash:"
about three months ago I set our 1751 router as the NTP server of our domain for both our AVVID phone system and our Microsoft Active Directory domain. Been working excellent up until last night. Our company's building had a power cycle and the router got rebooted. Not a huge issue, since it's actually been rebooted a couple of times since becoming the ntp server.
After it's reboot, the time somehow jumped ahead an hour according to all the devices that sync with it. Phone calls stopped working and Active Directory pretty much became useless.
I finally had to break all the devices off of syncing with the router and set them back to the way they were (phone servers sync with each other, active directory doesn't sync with anything externally). It took a few hours to get everything stable again, and I'm still working on parts this morning.
Here's what I've had setup now for three months, we're in Central Standard Time:
ntp clock-period 17179971
ntp master
ntp server 69.26.112.120
and I set the "clock timezone CDT -6" It's been like that for three months and everything was fine till last night when it went out of wack.
I have a Cisco 1751 that I wanted to use to create another network behind my Actiontec m1424wr Verizon router. My plan was to connect a linksys wrt54gs to the Cisco router for device connectivity. And I wanted everyone else in the house to still be able to use the Verizon router as expected. I know this is probably not the best way to create an internal network. But I am studying for the CCNA & CEH and just wanted to use the Outdated Cisco IOS on the 1751.
View 3 Replies View RelatedI have configured cisco 1751 router for internet with nating. Internet browsing working fine. But We have polycom hdx 6000 conference system to connect from remote site.
1. While calling remote ip it is ringing and connecting but not displaying any thing on the screen but their side is displaying.
2. When they call our side ip it cannot connecting.
I have connected netgear router then video conference is working fine (with out port forwarding also). If I configured that router between 2 local sites (not on internet line) its working fine where i did not configured any thing just given routing. Configure same situation using internet leased line.
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedI have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedMy wife's laptop will disconnect from our ATT Netscape router/dsl modem. The error we get is that the "security types do not match" ultimately we have to reboot the router and then her laptop will connect for a while. (we do not have this problem with any other devices that use this wifi connection.
View 1 Replies View RelatedMy linksysBEFW11S4 router shows a NetWork Key of let's say "mister", when I try to connect a new laptop using this key it comes up with Invalid Key.
View 2 Replies View RelatedI have a Dell Inspiron 1564 with the Dell 1397 WLAN Mini-Card. How do I use its Wi-Fi abilities to connect to the Internet?
Do I need a wireless router with a modem built in? Do I have to use a service provider, i.e. Bell, to make the connection and
therefore pay more service charges per month? Is "Linksys" a good name in routers? Should I buy the router at one of the big box retailers?
even though I have successfully added the network manually, using the same settings as my other laptop which has no trouble connecting. So now, the network appears in my "Connect to a wireless network" box, but whenever I try to connect, it says "Windows cannot connect to *name of network*" So when I troubleshoot the problems, it states "Check your wireless settings. Make sure your computer is in range of *Network* and that the network settings match the wireless router or access point settings." I KNOW it's in range because my other computer is connected properly right next to this one. So it must be a problem with my network settings. Though I don't see how that can be because my settings on both computers are exactly the same, but one's connected and one's not. Could the problem simply be that I haven't logged on to my router online to add this computer to the network?
View 3 Replies View RelatedCan Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedWe have pair of Cisco Nexus 7018 with four eight port 10gig modules.I have created two VDC's with mixing 10gig ports from diffrent modules.Now we requied some one gig SFP ports and we are planning to buy 48 port 1gig sfp+ card.My question is can
1- Can I still mix and match 1gig and 10 gig ports in two different VDC's? (1-24 for VDC1 and 25-48 for VDC2)
2- All 48 port module hve to allocate to one VDC which alreday have all 10gig ports.
If I want to use the command match protocol xxxx when configuring traffic classification for QoS, is necessary to have the following licence?
-FLASR1-FPI-RTU
-Flexible Packet Inspection RTU Feature License for Cisco ASR 1000 Series.
I have a problem with latest Anyconnect Mobile clients, on any device(iPhone,PC..) I have this error message.Anyconnect cannot verify the VPN serverAll certificates(rootCA,userCER) - installed on client side, all of them are trusted.
View 1 Replies View RelatedI'm getting an "ACL does not match proxy IDs" error that I'm not able to troubleshoot, googled this with a lot of results, tried some; but nothing applied.I have setup 2 tunnels, 1/one from a pix 515e (office) to an ASA 5505 (hosted server) for my guys to access the hosted server2/A second one from the ASA 5505 to my client's firewall so that its equipments can reach the hosted server and from the hosted server reach the equipments.Both tunnels are working fine, my issue comes when I'm trying to join my clients equipments from my office, ie cascading the tunnels.
This is the first time I'm trying to cascade some tunnels, no issues with other vpns I have been building.I'm joining the configuration of the pix and the asa and an extract of the syslogs showing the error, any obvious error I haven't seen!
This is happening to me to multiple computers on my domain. When it happens i can only log in as a local user or if I unplug the network cable, log in and then re-connect the networkThe time on all these machines is correct within at least 1 minute but still it's throwing off this error. When reading about this problem I see many fixes that all relate to how to sych the time on the PC.
View 1 Replies View RelatedData link-ARP,RARP, presentation-SSL,TSL,ASCII,JPG, Session layer-ASP(apple talk session protocol),SCP are these correct?can your provide 2 new protocols for each with the long name?
View 17 Replies View RelatedOn the laptop, the info bar is on the left side, the website tabs on the top, this shifts the other computers screenview down and to the right, it also cuts off the right side and bottom, with still leaving space on the right side and bottom. The pointer on the lap top does not line up with the desktop, because the screen is shifted, but only a portion of the screen is visible anyway. I used the same password and log in on both computers, don't know if they have to be different.There is full a screen option at the top right, but this causes the top tabs and info buttons on the left side to go black.
View 3 Replies View RelatedI live in a shared house, and I am the only one who has been experiencing issues connecting to the internet. I have to ask a housemate to reset the server, as this is the only thing that works.
When I am unable to connect, and I use command ipconfig, the following appears: Autoconfiguration IPv4 169.254.23.29 On the occasions when I am connected, the following appears in its place: IPv4 IP Address: 192.168.0.2
One tip that I came across was to check the box (Wireless Network properties, Connection tab) for "Connect even if the network is not broadcasting". I had hoped this simple solution would assist, but to no avail.
We have some ME3800MX router/switches running ME380x-UNIVERSALK9-M), Version 12.2(52)EY2. The Cisco website says:
The switch does not support these Cisco IOS router ACL-related features: # •Non-IP protocol ACLs (see Table 26-1) or bridge-group ACLs
how we would match ICMP traffic then?
We have an HQ site with a 2811 (w/ADVSECURITYK9-M) acting as the firewall. We currently have 1 ASA5505 that has an established ipsec l2l VPN. I'm trying to connect a 2nd ASA, but I've noticed I can only add 1 cryptomap to the outside interface. A show ver shows 1 Virtual Private Network Module... Surely that doesn't mean only 1 VPN?Do I use one crypto map, and add a second 'set peer' & 'match address' inside the crypto map itself?
View 10 Replies View RelatedI've Cisco7609-S with IOS 12.2(33)SRC2 met an issue is that "show ip route x.x.x.x" and "show ip cef x.x.x.x" shown next-hop is not actual switched next-hop.
For example, "show ip route 192.168.1.1" and "show ip cef 192.168.1.1" shown correct next-hop is 10.1.1.1, but the traffic destine to 192.168.1.1 actually not through 10.1.1.1, but always through the default route next-hop. Everything works normal after rebooted the router. Suppose it should caused by a bug? BTW, my Cisco7609 is runing BGP with ISP which received about 10K routes.
is it possible to construct the L7 HTTP class-map expression to match all URLs except one? I have 1 correct url, for example: /correcturl.* and want to redirect requests to all other possible URLs to this one, without the need to list them all in "possitive match" statements.
View 6 Replies View RelatedI have a 10Mbps connection link which I will like to reduce to 5Mbps on a 6509 switch as indicated in the config below. [code] After applying the service policy on the vlan interface, i got this "match vlan is not supported for this interface". I actually tried the rate limit command but I cant see the effect using the speedtest.
View 2 Replies View RelatedI created several rules to balance on a specific server somes apps. Everythings works great in http but no in https.In my example, i would like [URL] to be redirected to my server2 but it's always using the default rules instead of the L7CLASSSrv2. Today [URL] is well redirected. All other apps are correctly loadbalance with the stickyness effect but I can't handle the https connections.
class-map match-all L4-WEB-IP
2 match virtual-address xxxx tcp eq www
class-map match-all L4-WEBHTTPS-IP
2 match virtual-address xxxx tcp eq https
class-map type http loadbalance match-any L7CLASSSrv1
[code]....
I am running ASR1002 with latest XE IOS version asr1000rp1-adventerprisek9.03.02.01.S.151-1.S1.bin configuration bellow
router bgp 65000 bgp router-id 1.1.1.1 bgp log-neighbor-changes timers bgp 5 15 ! address-family ipv4 vrf LABR01-VRF bgp router-id 1.1.1.1 neighbor bgprrclient peer-group neighbor bgprrclient remote-as 65001 neighbor bgprrclient password 7 1234 neighbor bgprrclient update-source Loopback0 neighbor bgprrclient version 4 neighbor bgprrclient route-reflector-client neighbor bgprrclient route-map set_weight in I then tried to create new route-map and get error that match next-hop can not be used on inbound
route-map set_weight permit 10 match ip next-hop prefix-list thirdparty match as-path 1 set weight 1000
LAB-ASR1002(config)#route-map set_weight permit 10LAB-ASR1002(config-route-map)# match ip next-hop prefix-list thirdparty% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match Not sure why Cisco is not supporting a pretty basic feature for BGP route maps.I tried looking into matching other variables but I am unable to get same result as I have same routes on bgp table from multible inbound peers.
I also get this message when configuring tacacs. I looked for "new" cli but no luck:LAB-ASR1002(config)#tacacs-server host 2.2.2.2 This cli will be deprecated soon. Use new server cli
i want to ask , how to match youtube in my qos, i want to give youtube the best priority in the rush hour. currently im using an acl that match the ips of youtube but i think its not sufficeitt :
View 5 Replies View RelatedI am setting up officeexten. I have placed the officeextend wlc in the dmz with an mgmt ip of 192.168.10.2. in the process of anchoring this to the internal wlc. Also the ip on the firewall for this interface is 192.168.10.1
1. does the mobility group need to match the same on the internal wlc ?
2. Now do i need a NAT transnational on the firewall for the external WAN ip (AP primed address say 66.10.10.10) to NAT back to 192.168.10.2 ?
3. The 5508 WLC is running on ver6.0.199.4 (license level base) - will this support office extend?