We currently have 1 T1 coming into a 1700 series router for our internet traffic. We are looking to add 2 more T1's to this and was curious what would be a recomended router for this. Our provider is trying to sell us an adtran for $4200 which can handle 4 T1's.
View 4 Replies
We are facing strange issue in our network. We have a remote branch which is connected to main branch using Leased Line. Remote branch is having Cisco 1700 Router. Every day in the morning time the remote router is unreachable. We are not able to reach (ping/telnet) the remote Router but able to reach L3 switch/ LAN behind this router. The users from remote branch is also not able to reach the local router but they are able to ping the Main branch.Users in the remote branch are not able to access any resources in the main branch during the issue.
During the issue, we have checked the remote branch router and found the CPU utilization of the Cisco 1700 router is very high (99%). If we run "Show process CPU" command (please find the attachment) specially IP input process is very high (97%).
I have a Cisco 1700 series router (i dont know exact series number) running:
ROM: System Bootstrap, Version 12.2(7r)XM4, RELEASE SOFTWARE (fc1)
ROM: Cisco IOS Software, C1700 Software (C1700-K9O3SY7-M), Version 12.3(7)XR3, RELEASE SOFTWARE (fc2)
installed is a WIC-4ESW card.
This should be simple, cant get it working. in a nutshell... I'm trying to configure fa0 as a vlan "trunk" port trunking vlans 1 and 20 from my managed switch (switch is configured correctly) and i want fa1 on vlan 1 and fa2 on vlan 20.
another words:
fa0 tagged with vlan 1 & 20
fa1 untagged with vlan 1
fa2 untagged with vlan 20
Code:
! Last configuration change at 20:35:48 EST Sat Feb 12 2011
! NVRAM config last updated at 20:47:38 EST Sat Feb 12 2011
version 12.3
[Code] .....
I'm trying to configure 1700 K9 router to act as PPTP client and connect to Microsoft VPN server (in order to enable all clients on LAN to seamlessly access host on remote location). [URL]
I'm using GMS3 to test everything in lab environment. I managed to connect to Microsoft VPN server but the connection drops immediately. Below is debug info from router R1 (router R2 just simulates host on LAN) and configurations for both routers. The only clue I got from debug is that immediately before closing connection there's a message "CCP: Failed to negotiate with peer"...
R1#sh debug
PPP:
PPP detailed event debugging is on
MPPE Packet Details debugging is on
[Code].....
i got a big problem, during a configuration reset i got an electrical blackout. I have set the configuration back after a password reset and send the reset prompt. At the restart of the router the blackout take all for 10 seconds out. When i restart the system an connect the router with the hyper terminal i get the following output:
[Code].....
I think the config was lost but how can i restart the router and enter a new one?
We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
I have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedI was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View RelatedI have two sites with a dedicated, point to point, LAN, site 1 has a Cisco 1700, LAN IP: 192.168.0.101; Site 2 has a Cisco 1800, LAN IP: 192.168.1.101.From site 2 I can ping the router on the other side: 192.168.0.101, but nothing else on that network
From Site 1 I can't ping the other network at all,Both sites ping fine to their respective local interfaces. I also noticed, when trying to ping site 2 from 1, the "WIC ACT/CH" light blinks, otherwise it's off.
Site 1 has it's own web connection through COMCAST, site 2 is set to route through site's 1 connection to go out. The only thing the routers are doing are the actual connection between sites, and in the case of site 2, routing web traffic to 192.168.0.100, which is a Sonicwall on Site 1.
This was all working just fine, for a long time, up until yesterday, when the problem I described started happening.
The wan routers are 2600 and 1700. Conversions between the two? Pros/Cons of one versus the other? Regrets or horror stories for one versus the other?
View 3 Replies View RelatedI have an 1700 cisco Router and a ADSL connection to Internet.How may I use it on my home network?There's any configuration that I should to do?
View 3 Replies View RelatedI'm station overseas and it's really hard to access certain websites and servie like Netflix or ESPN. What I had created was GRE tunnel from my Home "A" to my current location "B" and route my traffic from point A to B using 2 cisco 1700 routers ( and It was working great) but now I can't use GRE nomore. I still have PIX and ASA on both sides and I was trying to do that over VPN tunnel but I can't ping VPN tunnel gateway( basicly what was next hoop in GRE) on the other end ( which is the main problem why I can't route traffic to remote site). I was wondering if I can still do the same thing over VPN tunnel that I did with GRE tunnel.
View 1 Replies View RelatedI have an old modem Cisco 1700 with ADSL as backup connection. I have configured PPPoA, the sync is OK and connection is UP. I get Wan IP et Gateway, (routes automatically added). I have added NAT and routes but impossible to go out.I try to ping an external IP but no response.
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname cisco-modem(code)
this is my first time configuring a cisco router. For instance, a cisco router 1700 with 2 ethernet WICs and 1 LAN port. We have 2 ISPs one more stable than the other. We use an RDP session to an external host identified by lets say IP address 200.1.1.2 using ISP2 to get to this computer. We use ISP1 for all the internet usage, web pages, youtube etc. We are thinking of using this cisco router 1700 to make the packet filtering and routing of this RDP session to the correct ISP2 since we only have 1 NIC per computer on the LAN side.
The main idea would be:
| YES -----> ----------- then use ISP2
LAN---------> Are the packets RDP ?
| No--------> ----------- then use ISP1
Does this can be achieved using packet filtering using extended ACLs and to be router from the lan interface to route rdp (port 3389) packets to ISP2 WAN interface?
As a matter of fact i am new to this field .I have cisco 1700 series router which has ea0 and FE 0 port
E0 connected to LAN and FA0 for ISP ,both are configured wit publisc ip.and ststic route to ISP. (E0 connected to switch and fa0 connected to ISP MUX)
When i issued sho arp command i have received more than 30 entries of MAC and IP address . I am wondering how i received this much mac in arp table.
I have a DI-604 D-link router, is it necessay to upgrade to newer router to get faster access to internet? Upgrade Firmware? I have a PD950 processor with Win XP pro and use it for DAYTRADING streaming data and fast executions.
View 5 Replies View RelatedI recently upgraded my internet speed to 10 MB (used to be 5) but the internet speed in my PC got slower.I ran a speed test and the download rate was 2 MB while on my laptop it was 10 MB. My PC is clean of viruses and its connected to the integrated router via cable.
View 5 Replies View RelatedAfter upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites. In some instances, when the page does load, it lacks many graphics. Frequently, I also receive a "server not found"error. In all cases, reloading the page (once it has loaded) results in a complete page display. This is occuring on two MacBook Pros and also on an iPad. The router is a version 1, so no further upgrades are available. I contacted support, but since it is out of warranty, they are unwilling to assist. Prior to the upgrade, everything worked fine, as it has for 5 years.
View 1 Replies View RelatedI have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies View RelatedI just recently upgraded my computer to Vista from XP. Since then my computer connects to the internet and runs applications such as Star Trek Online and Skype ok but it won't load pages in any internet browsers.
View 12 Replies View RelatedI am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
My Netgear DGN2200 (Name NetgearCS) won't check for firmware upgrade because it says no connection to internet so unable to connect to the Netgear Servers - Yet this laptop I am currently using (wireless connection is turned off on laptop but not router) is wire connected to this same Netgear router and I have internet connection because I am able to post this enquiry. Note the Netgear DGN2200 router gets its internet connection from my Sky Router and is connected by wire to this Sky Router. FYI my iPhone is connected wirelessly to this Netgear DGN200 router (NetgearCS) and is able to connect to the internet. Do you know why my Netgear DGN2200 cannot check for firmware updates?
View 1 Replies View RelatedI have a Vostro 3300, which was working very well, and when I upgraded my OS from Win7 to Win8 my internet speed through wireless connection became very low, I checked for a driver update but did not find any that is compatible with windows 8. I also tried some old Windows 7 drivers with and without "compatibility Mode" but still not working. I should also mention that when I connect to the internet through Ethernet, I get the full speed.
View 3 Replies View RelatedIs it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies View RelatedRegion : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225
ISP : Rogers
Ever since upgrading my firmware from 120426 to the latest(121225), one of my computer(windows xp, TP-link Nano) is frequently losing internet connectivity.I purchased the router a month ago and firmware 120426 was the version that came installed. The router would stop working about 3-4 times a week, requiring me to reboot it. Because of this I did some research online and found out about version 121225 which supposedly should improve performance and stability. After the firmware upgrade today I noticed that one of my computer is having a lot of trouble maintaining internet connectivity for more than 30 minutes. When checking wireless connectivity it would say that I am connected and that the signal strength is excellent. I'm also able to ping 8.8.8.8 but not www.google.com(I've tried ipconfig /flushdns and it doesn't solve the problem). I also have trouble accessing or pinging the router(192.168.0.1) with this computer.
I am really stuck with router requirement for one of our client. I need 891 SEC router. I think this comes with advanced IP services. What I have is 1921, with IP Base. can I upgrade 1921, so it will become alternative to 891 SEC.
View 1 Replies View RelatedWe have 1841 router (Cisco IOS Software, 1841 Software (C1841-ADVSECURITYK9-M), Version 12.4(9)T1, RELEASE SOFTWARE (fc2)), currently the router up and running on "c1841-advsecurityk9-mz.124-9.T1.bin" and when we try to upgrade the IOS with "c1841-advsecurityk9-mz.124-24.T7.bin" its not taking the new IOS. [code]
View 9 Replies View RelatedI got a new 1811 series router. Its sh version output is " flash:c181x-advipservicesk9-mz.124-11.XW6.bin". I need to upgrade to the latest IOS. How can i find a latest one? How can i upgrade to the latest one?
View 1 Replies View RelatedWe need to upgrade the RAM on our 3825 Cisco Router. Currently, it's 512MB and we want to upgrade it to 1GB. So do I just order another 512MB DRAM Memory? What is the part number that I need to order?
Here is the show ver:
Cisco IOS Software, 3800 Software (C3825-ADVENTERPRISEK9-M), Version 12.4(24)T2, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 19-Oct-09 21:05 by prod_rel_team(code)
We are having Cisco ASR 1006 Router with the XE Code :asr1000rp1_advance entrprisek9.03.01.00.S.150_1.S.bin The basic information we are having is
cisco ASR1006 (RP1) processor with 1717513K/6147K bytes of memory.
10 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
937983K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
Wanted to upgrade to the latest IOS XE 3.4.x but the memory requirement for this IOS is Dram 4GB. But the DRAM actually is 2GB as per show version command.Here the Physical memory is showing 4 GB so can we upgrade this IOS XE?
My professor have asked us to do an IOS upgrade for a Cisco 827 ADSL Router. But I´am having problems to find the appropiate IOS image. The router original IOS is c827-y6-mz.121-1.XB and it supports routing protocols like rip bgp eigrp ospf is-is, etc.
Now, we have to find a newer IOS release that supports the same amount of routing protocols. This Router has only 24 MB DRAM and 8 MB Flash. We have tried with a IP PLUS/FW/IPSEC release 12.3(26) but when I write : route ? it only shows eigrp, odr and rip.
I am searching for a newer release that fits in those 24 MB and which has the other need routing protocols like ospf,bgp, etc.
an IOS image that meets what I am searching for?
I am looking to upgrade a 2811 router to 15.1.2T and see in the release notes that this image is only compatible with the "C Series" older ISR routers? What is a "C Series" ISR and how do I know if I have one?
View 4 Replies View RelatedI have router 1905 which running IOS is C1900-UNIVERSALK9-M , how can I upgrade this IOS ?
View 5 Replies View Related
