Cisco WAN :: Router Was Not Using Whole Bandwidth Of 3044
Nov 5, 2012
I have a bundle of 2 T1 into a multilink interface. However, I have encounter an issue, last week, our ISP lost one of the T1 and it went down hard for at leats two hours. Once the T1 came up, the bandwidth still was 1544, but once I shutdown and no shutdown command in one of the serial interface the bandwidth came up as 3074. Here is my basic config for the 2911 router. [code]
I just don't know why the router was not using the whole bandwidth of 3044.
View 1 Replies
ADVERTISEMENT
Sep 9, 2011
We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies
View Related
Aug 9, 2011
I am having trouble with a T1 connection between a cisco 7200VXR and cisco 2600. I have no problem connecting across it, but when I run a download across the link I get a flat 6KB/s. I can't seem to find what is wrong in my configuration that would be causing this.
7200 Router:
#show running
Building configuration...
[Code]....
View 9 Replies
View Related
Apr 7, 2011
I live in rural Alaska and use satellite internet with 1.5mbps rate and 4gb rolling weekly download limit. I was wondering if there are any wireless routers I can buy that I can set a bandwidth limit for the specific router. Due to teenage girls in the house we hit the weekly limit in a day or two because of all the music videos and such that they watch on you tube, it is annoying getting limited to the 256kbps download rate so often.
View 5 Replies
View Related
Nov 18, 2011
i have DSL router in my home using wifi by it... it is on sharing by DHCP mode. and my question is how to restrict bandwidth to other users? like full access to one use and 50-60 kbps to another user?
View 1 Replies
View Related
Aug 29, 2012
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
View 7 Replies
View Related
Mar 20, 2012
I have just received Time Warner Cable and get 16Mbps down from them directly through their modem (motorola DOCSIS 2.0 modem- SB5101) to my PC (using speedtest.net). When I then connect TWC's modem through my 2801 router on fa0/0, the download rate I get is considerably slower (on the order of 3-4Mbps via same testing method). What am I missing?
Here is how the passthrough interface is setup:
interface FastEthernet0/0
bandwidth receive inherit
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
I have attempted removing bandwidth command - nothing changed with it not there. I have also hard coded the speed and duplex to 100/full to no avail....
Other possible relevant configs:
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 dhcp
access-list 1 permit 192.168.1.0 0.0.0.255
Basically this things is wide open... for testing but the download speed differential is perplexing to me.
View 10 Replies
View Related
Jan 12, 2011
can i merge two sources of bandwidth into one router ?
View 1 Replies
View Related
Jul 12, 2011
How can I limit the bandwidth of a router (DIR 600).
View 1 Replies
View Related
Jul 29, 2010
I will have this one router. Its f0/0 will be for the Internet connection with bandwidth of 30Mbps. Its f0/1 will be connected to a switch for internal networks. This link will be separated to 3 VLANs for 3 internal networks. I'm wondering if there is a way to gurantee 10Mbps for each VLAN but allow use up to 30Mbps when another two VLANs are not using any Internet bandwidth? I only worry about download bandwidth from internet.The 3 internal networks will all have public IPs and they belong to their own subnets. There won't be NAT/PAT.
View 18 Replies
View Related
Jan 6, 2011
I got connected ASA ----- ROUTER 2811) to metroethernet switch from my ISP , with a 4MB of bandwidth but the internet connections to all my LAN has been frozen and we lost connection to the internet, to restart the internet service I need to boot the ROUTER 2811 - and ISP switch to rollback the internet operation,My ISP support tell me if is possible to set up the traffic bandwidth in one or both borders devices, ( ASA 5510 or ROUTER 2811)
View 3 Replies
View Related
Jul 3, 2011
what maximum bandwidth supoort by CiscoRouter model No. Cisco 7507 RSP-16-MX , Cisco 3745 and cisco 2522 ?
View 4 Replies
View Related
Aug 27, 2012
I have a requirement where 3 Branch locations of an organization is connected to their hub location via MPLS.They have an internet connection only at HUB as shown in the diagram (Attached)Now all spoke locations should access internet via hub.At spoke locations is there a way that I can have Cisco 2900 router and dedicate only 30% of the WAN bandwidth for internet browsing traffic.Remaining 70% should be used for accessing applications at hub.
For example if i have 5 Mbps Mpls port at spoke I want to dedicate only 1 Mbps for internet browsing traffic remaining should be dedicated for accessing the application at hub.How can we acheive this? Can it be done by using PBR and rate limiting?
View 2 Replies
View Related
Mar 7, 2012
I got a 5MBps Lease Line Connection via FAST ETHERNET PORT. i got a Cisco 1841 Router.
I want to distribute bandwidth in this ratio 2MBps/2MBps/1MBps
2MBps = Office Connection
2MBps = Computer Laboratory Connection
1MBps = WIFI Connection
1841 has only 2 Fast Ethernet ports
so im planning to add up a 2modules of 2-Port Fast Ethernet High-Speed WIC for Cisco Integrated Services Routers
View 18 Replies
View Related
Aug 11, 2012
my client insisting to set a dscp value of 56 (= CS7 , the highest priority) for their video packet without any bandwith restriction in the input of fast ethernet port and PPP Multilink serial output port of the 7513 router. What will be the outcome at time of video streaming and video conference ? As this dscp value CS7 is the highest priority and reserved for network only.we are using ospf routing (some of the network is connected through this multilink port via ospf routing), also this ethernet is connected to various statice routed ip network via cisco asa and cisco 4507. The keep alive ospf neighbor router will be lost or not?
View 2 Replies
View Related
May 21, 2012
I apologize in advance if this is a novice inquiry, but our company just switched from Point-to-Point T1's to Metro Ethernet.
On one point-to-point, from our main office to one of our high profile locations, we had two bonded T1's. Now this site has a 3 Mbps Metro-E link, but it's being over-saturated. I don't know what type of QOS implementation our T1 provider had, but it prevented flooding. Now, I'm getting horrendous latency as the office peak hours approach since there is no QOS on the mesh by our Metro-E providers.
Ultimately, my question is: what's the best way to set a Fast Ethernet port on a Cisco 1800 series router to limit all bandwidth to 3 Mbps? At the moment, I don't have a preference in which traffic takes priority. I tried the rate-limit command, along with a speed calculator I found online, but that slowed the network down immensely.
View 19 Replies
View Related
Oct 7, 2011
what are branded include bandwidth control function , dual WAN port
View 1 Replies
View Related
Jun 11, 2011
I just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.
I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.
View 7 Replies
View Related
Jul 24, 2011
I have a dell poweredge 830 (3.0 dual core pentium, 2gb ram, 2x160gb hdd in raid 1, dual port intel gigabit card). I'm trying to find a router OS that logs bandwidth by ips on the lan. I tried untangle and clearos neither of which have a feature (or one that I can find) that logs the bandwidth by ip. Apparently pfsense has a package you can install but I have never been able to get pfsense to work on this pc, it always errors in one way or another (on the 2.0rc3 I can't access the web page, it says it is missing a file).
View 19 Replies
View Related
Jan 13, 2013
limit the bandwidth used by certain wireless devices on my network. The problem I'm having is of priority. For some reason when someone is watching Netflix on my laptop (wireless) no other device has any bandwith available to it, so while someone is watching Netflix my hard wired desktop can barely load Google.com much less do anything useful.I'm using a Cisco ValetPlus M20 wireless N router.allocating at least a minimum amount of bandwidth to wired devices?
View 1 Replies
View Related
Apr 22, 2011
We have some point-to-point sites linked with our HO with 10-30mbps speed. We have provided DID telephone lines to these sites as well.
We want to limit the bandwidth with 1mb bandwidth only and also make sure that the voice traffic (DID telephone lines) gets the priority over all other traffic even if they are utilitizing the 1mb link completely. We have some Cisco 1841 routers that we are planning to configure on the main uplink on each of these sites. how to give the priority to the voice traffic yet limiting the bandwidth to 1mb.
View 8 Replies
View Related
May 1, 2012
I have a cisco Swtich SGH 300-20 Gigabit switch i configure 2 vlan one is default and one is vlan 10
Vlan 1 ip range 172.16.0.0/23
Vlan 10 ip range 172.16.2.0/24
Client on Vlan getting Proper IP from DHCP Server all i need is to distribute internet bandwidth we have 6/3 mb and i want to give 4/2 mb to vlan 1 and 2/1 mb to Vlan 10
Int Gi16 on switch is configured as trunk port and is connected to cisco 2811 router
what are the command used to distribute bandwidth between these 2 vlans
View 3 Replies
View Related
Oct 20, 2011
I have the following setup:
Cisco 1921 is my core router and connected to it is a 30 Mbit fiberline
VLAN1
VLAN2
Now, the thing is that i want VLAN2 to have a 5 Mbit bandwidth limit to Internet but full speed to VLAN1.
I have played around with Rate limit without success.
I also have access to cisco switches that can limit the bandwidth.
View 23 Replies
View Related
Aug 11, 2011
I cannot find this info on the cisco site.
View 2 Replies
View Related
Apr 8, 2011
I am using using 2 broadband with tp-link dual wan router 10 pc using the broadband.does any one know about the router who controls bandwith there is option available in Tp-Link Dual wan router but its not working...is there any router which automatically takes bandwith and allow as per my details.
View 1 Replies
View Related
Oct 12, 2011
i have tenda ADSL router using the internet of Nepal Telecom, Nepal and distributed to two users. now i want to limit the speed of the other user to least and i want to achive maximum speed of the subscription but have no idea to manage it
View 1 Replies
View Related
Jan 7, 2013
So my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
View 1 Replies
View Related
Sep 10, 2012
I have about 4 different devices accessing the same network, which lags my pc gaming severely. I was wondering if there is a way to set my IP to the main priority. I am using a Westell 7500 router.
View 1 Replies
View Related
May 15, 2011
I currently use Verizon FiOS 20/5. The speed has been great until the day my cousin and his parents moved in. They also use our FiOS connection and I have came to the conclusion that my cousin's laptop is eating away all of the bandwidth which makes all devices using FiOS have extremely slow internet speeds. I know it is his computer because I logged in as admin to the Verizon FiOS page (192.168.1.1) and I saw that he is using several P2P applications and downloading torrents as well. Is there a way I can limit the bandwidth he is using so that the internet speed can improve? I looked at the QoS tab and tried to play around with the settings, but I don't want to mess it up. The router I have is Actiontec M1424-WR (Verizon FiOS 20 Down/5 Up). A lot of sources I am reading says that I have to use the QoS, but I don't know how to use it on the site.
View 3 Replies
View Related
Mar 3, 2011
I would love to see this added in a future firmware release. I imagine others would welcome it as well that have caps with their isp.
View 9 Replies
View Related
Jun 8, 2012
E4200 V1 QOS can add downlink bandwidth？
View 3 Replies
View Related
Mar 1, 2012
Telefonica router (this my internet provider) --> WRT12N --wireless/eth--> my laptop
With that configuration I get a 1Mbps band with But in this configuration Telefonica router (this my internet provider) -- wireless/eth--> my lapto I get 7Mbps.Using always the same port of my telefonica router.Why the WRT120N is not providing the whole bandwidth? Is there any option in the router that divide the whole bandwith (7Mbps, almost 8Mbps) among the four ports of the wrt120n (giving 1Mbps per port)
View 1 Replies
View Related
Apr 10, 2013
Any idea for limiting bandwidth on cisco 892F router? We have 2 VLANs through our LAN and one must be limited upto 1Mbps or 512Kbps.
View 2 Replies
View Related
