Is there anyway to configure a 5508 via the SFP ports? Or do you have to use the service port for autoinstall or NCS auto provisioning? It looks like it grabs a DHCP address but it doesn't seem to like telnet,ssh ,HTTP or HTTPS.
View 2 RepliesI have a pair of WLC 5508's. I am installing 7.4.100 on them and they are properly licensed. I am looking to preconfigure these and ship them to our site. My questions are:
1) How much configuration do I need to setup on the secondary controller (ie. same SSID, interaces, ap group, etc...)?
2) Do I need to configure Mobility groups for this HA Cluster?
I have Cisco 5508 Wlan Controller Software version 7.2.103.0 and I have Cisco AIR-CAP3602I-E-K9 Lightweight Access Points network and its working fine now I want to configure the Repeater in this network. Because there is one area we cannot layout the cable. How to add the repeater and how to configure the repeater in wlan controller network.
Do i need the change the software of Wlan Controller to support Mesh Network or this version 7.2.103.0 can support the repeater because for 1 access point i dont want to upgrade the version.
I have configured EAP-FAST local authentication on a 5508 running 7.0.116.0. I am trying to connect using a motorola/symbol MC3090. In the handheld, It appears to be failing due to receiving no PAC. On the 5508, it just looks like a timeout. Are the PACs created on the 5508 automatically, or do I need to generate one?
View 1 Replies View RelatedI would like to know if microsoft 2008 server RADIUS server could be use for authentication on Cosco 5508 instead of Cisco ACS.
View 4 Replies View RelatedConfiguring HP switches for Flexconnect. I am not sure if or not its doable? Access Points are 2600 and 3600 with 5508 as a controller. Idea is to keep the branch traffic local but the switches are HP.
View 3 Replies View RelatedWe use a wlc model AIR-CT5508-K9 with eight built-in ports. I would like to know if it is possible to change the speed of these ports down to 100Mb. At this time, they are set to auto and 1000Mbps.
View 3 Replies View Relatedi have a problem with our new 5508 wireless controller (7.0.116.0).
Port 1 is the system default "management" (Port 2 is backup). Dynamic AP Management is disabled. Port 3 is a new dynamic interface "ap-manager 2" with Dynamic AP Management enabled and has a ip in a seperated VLAN which is not routed.
When i am connecting the AP (1260 series) to the "ap-manager 2" interface, then it will not join and i get an error message on the WLC:
*spamApTask1: Mar 05 14:52:12.783: %CAPWAP- -DISC_INTF_ERR1:capwap_ac_sm.c:1453 Ignoring discovery request received on non-managementinterface (3) from AP
When i am connecting the AP to the "management2 interface, then it is working fine. But i don't want the APs in the Management LAN. I want them in the separated no routed LAN explicit for the APs.
I have cisco 5508 wlan controller with 8 ports can i connect 8 switches on these port. If i connect what will be configuration to work all these ports because only port 1 is working if i connect to switch remaining ports when i connect status showing is enable but not working.
View 2 Replies View RelatedDoes anyone know if it is possible to use an 5508 WLC running version 7.0.116.0 as a DNS box? Was not able to find anything in the config guide.
View 2 Replies View RelatedIf all you have is a high end cisco router available, can you plug in hosts to the router ports, and configure them within the same subnet? (When I try to configure ports within the same subnet, I receive a "same subnet" error.
View 3 Replies View RelatedIhave a 3560 w/multicast support and I'm trying to configure a simple environment. I have 2 ports configured, one for the multicast server and the other for the client. Each are on their own subnet, so I have an ip route between the two. My run config on both ports is:
ip multicast-routing distributed
interface fastethernet 0/3 & 0/4
ip pim version 2
ip pim sparse-dense-mode
I'm using vlc server /client configured to use 224.0.0.1 on my isolated network. I can see the mulitcast traffic going into the port, and I the client is sending reports, but I think the 3560 is dropping the packets, since I don't see them coming in the client port. Need to configure a simple multicast environment using 2 ports on a Cisco 3560.
At the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG). In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG". None of the SSIDs are "anchored".
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs. This site contains two customers. One customer is the Main customer with the second customer leasing space.
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan). I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500. It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site. This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
For my test, I am starting simple. I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low). I have anchored this test WLAN to that controller. At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site. I am unable to obtain an IP address from the remote site. I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?
How to configure ssh in all access points ( cisco 3500 Access points ) under wlc 5508 ?
View 3 Replies View RelatedIs possible connect and configuring two cisco wlc in high availability to 3 switches in stack 3750 in difference ports?For example
WLC A (Primary) - SWITCH MASTER
WLC B (Secondary) - SWITCH SLAVE
How can i connect the wlc's in HA to get a redundancy in the stack?
I have a Cisco 5508 controller and am considering using LAG. Can I enable LAG but only use 2-4 of the 8 available ports on the 5508? I am asking because currently I don't have enough ports on my 3750G switch to accomidate all 8 ports on the 5508.
View 2 Replies View RelatedCan you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies View RelatedIs there a way to associate spare firewall ports with another port that is being used..For example...int gi 0/2 is being used currently for my web dmz. Its ip is 192.168.10.1..Is there a way for me to associate gi 0/3 with the same layer 2 as gi 0/2 ?
In my webdmz I use 2 ACE 4710 proxys in FT mode. I used a layer 2 switch to connect firewall and proxys together.
I would like to eliminate this switch if possible..and connect both 4710's (layer 2) direct to firewall.If I could make gi0/2 - 4 part of the same vlan, then I would be good to go.
How many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies View RelatedOne of techs accidentally connected two access ports from different switches together. Since then, LMS is alerting them as being Link ports down. I tried to default the config and set them to access ports without any success. what I should do in LMS to recognize them as access ports?
View 2 Replies View RelatedI'm using two cisco 1242 AG access points to configure WDS feature. I've named the accesspoints as AP1(acts as WDS) and AP2. Since I've only two accesspoints, I've configured the AP1 to act both as a WDS and as a regular accesspoints.Further I'm using the local radius server within the AP1 to authenticate both clients and infrastructure accesspoints. And both APs are connected to a router (which act as a dhcp server) via a unmanageble switch and both accesspoints are getting registered with WDS.But the issue is when I tried to connect to the configured SSID, it promts me a "authentication window" but after entering the configured username and password, i'm not getting authenticated by the AP.
I've attached the configurations of both APs to for your reference and I've used the following cisco document as a guideline to crate the WDS. [code]
I've created two configurations. One for the router side and one for the AP point side. However, I am having trouble getting the internal AP to bridge to the router properly. It is my understanding that the Wlan-GigabitEthernet is the internal interface connecting to the AP and the BVI1 together. I can't ping any ip address on the router side from the ap and the radio is active and we can see it but it seems that it doesn't give an ip address. [code] Is it a VLan issue or an ip issue but I could use a second opinion. I've included both configurations.
View 1 Replies View RelatedI have an access point 1310. I want to add to the WLC as an access point. It have been configured with IP address correctly and the radio interface is up. I need to add it to the WLC as CAPWAP.
View 5 Replies View RelatedNeed to configure Cisco 1142 N access Point togetherwith the Cisco Switch . I have a POE Switch 4510 and Cisco 1142 N Cisco AP . I have one management vlan 5 & User VLAN for WIFI VLAN 10 . The problem is when i make the POE port which is connected to the AP as trunk port means : [code]I am not able to ping the management IP allotted from VLAN 5 . However when i make it as access i am able to ping the managament IP . But for both the VLANs to work it should be in trunk mode & in cisco i can either assign the port as access or trunk .Post this i would configure the 1142 N with Cisco SG300-10P POE Switch . I guess if issue with my 4510 gets resolved the same way i can configure SG300-10P as well .
View 6 Replies View RelatedI have a Cisco Aironet 1130 Series setup as a Root AP and a Cisco Aironet 1200 Series Access Point setup as a Repeater. However i cannot get this to work. I can connect fine to the Root AP but not to the Repeater.
I receive the folloiwng error on the Repeater AP.
'*Mar 1 00:00:24.887: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response'
The Root access point is connected to a Cisco router (192.168.168.1) which is the gateway to outside and is also acting as a dhcp server.
Both SSID's and authentication/encryption match.
Im using the the below mac-address for Authenticating the Repeater to the Root with the parent 1 command. Should i be using the mac address of dot11radio 0 of the Root AP??
AP_Root#sh interfaces dot11Radio 0Dot11Radio0 is up, line protocol is up Hardware is 802.11G Radio, address is 001b.2b69.6ca0 (bia 001b.2b69.6ca0) MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255
I'm trying to ensure I have wireless coverage in my entire house and having extreme difficulty getting all machines to play nicelyWireless modem router #1 (downstairs in my house) is connected to the ADSL line and has the following config:IP Address = 192.168.1.1 DHCP on DHCP pool 192.168.1.3-192.168.1.100 Subnet = 255.255.255.0 Wifi channel = 1 Wireless router #2 (upstairs) is connected by ethernet cable to Wireless modem router #1 and has the following config:IP Address = 192.168.1.2 DHCP off Subnet = 255.255.255.0 Wifi channel = 11 Different SSID and encryption key to Wireless modem router #1 With this configuration, I can connect to the internet via both routers and all seems to be well. Except... having established a connection through either one, my machines will only make a pretend connection with the other one. By "pretend", I mean that the (Windows) machine says it has an excellent connection to the router but can only see machines on the LAN - it cannot get to the internet even though other machines are connected through the same router to the internet.
For example, if I'm sitting next to the downstairs router and establish a connection with it, all is well. Then I move upstairs and my machine switches to the upstairs router. Signal strength will be reported as "Excellent" and I'll be able to connect to the local NAS or printer but no external devices or sites.I have tried having the same SSID and wireless configuration on both but the result was the same.Today I read the suggestion to enable the DHCP server on the 2nd router but to set it to distribute a different non-overlapping IP range (i.e. router 1 can have a pool of 192.168.1.3-192.168.1.50, and router 2 can have a pool of 192.168.1.51-192.168.1.99)
I know that you shouldn't update router firmware from a wireless connection. The other day, somebody told me that you shouldn't configure a router(such as changing passwords, channels, etc) from a wireless connection. I change my router settings from a wireless connection all the time.
View 1 Replies View RelatedGot road runner already get internet with wifi router, but want to set up password protection for internet access. the wifi is default now.
View 1 Replies View RelatedI have currently Ciso4404 WLC installed which is in vlan4001 with the 172.16.10.0/24 subnet
I have bought Cisco 5508 WLC recently as AP count is increased... Can I install it in same vlan and subnet? If yes what would be the setting for APs to join... If no how can I configure it with other vlan and subnet..
I am attempting to configure two Aironet 1040 series wireless access points for the first time and am having some difficulty. This office does not have a RADIUS server so I would like to set them up to use WPA2 with a pre-shared key. However just how this is accomplished is not immediately apparent. I have attempted using both the command line interface and the web interface, but I get errors in both places. It doesn't seem like it is all that difficult, we're just talking about a few lines in the configuration file.
This is what I have so far:
Current configuration : 1684 bytes
!
version 12.4
no service pad
[Code].....
good docs for configuring a 1260 autonomous AP?
View 1 Replies View RelatedI’m configuring a Cisco 1142n AP in autonomous mode. The networking part is successfully working, multiple VLANs, SSIDs etc. I would like to configure one of my wireless networks to work with WAP2-PSK and the other with WPA-PSK.I’m confused as to what encryption to set on each radio and the ciphers to use on the SSID for each vlan to enable the best possible security. I’m not using a RADIUS sever in my network .point me in the right direction with the right CLI commands?
View 12 Replies View Related