D-Link DIR-655 :: 802.11n Only Getting 54mbps?
Jan 19, 2011
why I would get only 54mbps on an 802.11n connection with laptop sitting right next to the router with 100% signal strength according to the router? Setting are mixed mode: 802.11n & g, Enable channel scan, Best Transmission Rate, Auto 20/40 width.
Could it be due to WEP security (need to use this for my kids Nintendo DS to connect)
I don't care about getting 300mbps like a lot of other are talking about. I just want more than 54mbps!
View 4 Replies
ADVERTISEMENT
Apr 29, 2012
I bought a new system case, installed everything from the old case added 2 additional fans and now my wireless network speed dropped from 150 to 54 aand I have no clue why. New case has a bottom mounted PSU and old had a top mount so netcard sets about 4" higher then it used to but other then that nothing has changed. Also when I brouse thru things I noticed this "LocalSystemNetworkRestricted" allot of places and do not remember seeing this before, I have used a different system to check out my router and it is same as always.
[code]...
View 11 Replies
View Related
Sep 19, 2012
My laptops wifi speed drops from 54Mbps down to 1Mbps which is often causing me to disconnect from web application etc I am currently using a usb wifi dongle and the speed does not drop from 54Mbps which has made me believe the problem lies with the laptops internal wifi settings, after re installing my internal wifi's driver to a more recent version the problem is still the same, I am using a lenovo t61 laptop and my wirless router is a D-LINK DSL-240R, how to fix my internal wifi so that its speed is a constant 54Mbps as my 2 other laptops and notebooks are all at 54Mbps, because of this I believe this is an isolated problem.
View 14 Replies
View Related
Feb 12, 2012
I currently have a 802.11 G router of 54mbps (its claims its a super G 108 mbps tough). My notebooks have 802.11 N built in. Im thinking of upgrading my router to a 802.11 N 300mbps.However, I know that this may be irrelevant unless I have a internet conection that can achieve such speeds. So how do I test my internet speed to see if G is bottlenecking?
View 4 Replies
View Related
May 5, 2012
Im trying to install this on a Dell Demension 4700 with win xp professional, I get as far as the setup, but can't go any further, the software wont let me set up any wireless.
View 2 Replies
View Related
Feb 24, 2012
I just installed a WRT320N for someone's home network, with the intent of providing better speed for network printing.
Unfortunately, all four of his n-capable Windows computers will only connect at 54mbps. Four different computers (Win7, Vista, XP), each with a different brand/model of n-capable network adapter.
I suppose I could try setting the wireless to n-only instead of "mixed". However, he's got a couple g-only devices as well, so that wouldn't work.
I tried updating the firmware to latest/greatest - no effect.
View 5 Replies
View Related
Dec 26, 2011
My E3200 is having issues with keeping the speed up on wireless G. I'm about 20 feet away from the E3200 and there is 1 6in wall between me and the E3200. My connection will not hold 54Mbps, its constantly dropping to 36Mbps, even down to 5.5Mbps faily often. Around 30 feet away there i will lose internet connection yet my laptop says excellent connection to wireless.
View 2 Replies
View Related
Feb 7, 2013
I have an SMCWBR14S-N4 router, and I'm using a usb wireless adapter that says it supports n, and promises speeds of 150 mbps. My signal strength is excellent, yet my speed is only 54 mbps. This is the only wireless connection on my network, I have 2 PCs connected at 100 mbps, and a Dish DVR connected at who knows what speed.
I've been trying to read questions and answers from others online, and I keep reading that ISP speed plays a role. How does my ISP's speed affect my wireless network's speed? (Plus, I run speedtest.net all the time and my download speed is usually 260 mbps.)
But my question is simply why is my speed so low and what can I do about it?
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Turion(tm) 64 Mobile Technology ML-34, x86 Family 15 Model 36
[Code].....
View 10 Replies
View Related
Mar 18, 2013
I have encountering a problem with a new installation at my clients side recently.We have a 5508 wlc and a bunch of Laps connected to it.Recently we associated a 1142ap to the same controller.The issue we are facing is that , the client laptops that are connected to THIS ap are showing maximum of only 54mbps in their network information dialogue box.Initially i couldn't understand why this could happen.But after a bit of research , i came to know that this could happen because of ``unticked`` data rates in the controller , or because of not using wpa2 with aes as the security standard for N-series access points.Now i have enabled all data rates in the High Throughput section as well as enabled the correct encryption standard.But still the issue persists.We have checked with multiple laptops , to rule out the possibility of a faulty n/w card
View 3 Replies
View Related
Apr 12, 2013
Region : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
View 1 Replies
View Related
Feb 14, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.
View 7 Replies
View Related
Mar 3, 2013
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
View 1 Replies
View Related
Feb 26, 2013
when I connect my DIR-655 to the Motorola SB6141 cable modem I notice that the link speed LED on the cable modem never glows blue indicating a gigabit connection, it only glows amber indicating a lower negotiated speed. I am using a Cat6 cable between the two devices and have also tried a Cat5e cable.
When I try and force the WAN port speed to 1000Mpbs in the router interface the cable modem link speed will not light at all with no connectivity. Only resetting to Auto WAN port speed restores functionality albeit at the lower negotiated speed setting.
I'm running the DIR-655 rev B1 at 2.03NA firmware level.
I did connect the modem directly to my PC that uses an Intel Gigabit ethernet card and still had the lower connection indication (Amber) so it seems that the modem might be faulty.
View 4 Replies
View Related
Jan 30, 2013
Region : Others
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP :
After I configure the WAN setting on TL-MR3020, my laptop unable to connect to my TL-MR3020 anymore, the message says "windows was unable to connect to TP-LINK_POCKET_3020_B5F9AD".
View 2 Replies
View Related
May 13, 2013
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
View 3 Replies
View Related
Feb 16, 2013
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
View 4 Replies
View Related
Dec 27, 2012
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies
View Related
Nov 20, 2011
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
View 7 Replies
View Related
Mar 6, 2012
I'm in an issue w/ on of our ISPs. We're using an ADSL line as a secondary light load line ( 16 MBit, /w PBR in place to separate the 80 and 443 from the business-critical applications running via a SDSL link. ).
I am on a 2611 XM with IOS 12.2, mated to a D-Link 321B modem running in transparent mode. After running smoothly for weeks, for a few days now, every night some time between 2 AM and 4 AM the link would die with the dialer showing:
Virtual-Access1 is up, line protocol is down Hardware is Virtual Access interface [code]....
To my knowledge, the only option to bring it up again is to reload the box . Taking into account that the router is our DHCP server and the date gets reset to 1994, interesting effects are the outcome of resetting the box.
Well, the ISP have checked their gear and keep saying that these report a "port error" ( quite unspecific ) and blame me that I have a wrong. config in place - which is here:
interface Dialer2
description ecotel Bridge
ip address negotiated
no ip proxy-arp
[code]...
View 10 Replies
View Related
Jan 30, 2012
I have 1.00 build 0522 and searching the support website I see no link. But reading here I see there is a later version.
View 1 Replies
View Related
Jan 9, 2013
I have a DIR-655 that I have been using for a while (b1 revision). and suddenly I noticed my wifi speed fluctuates constantly. My lenovo Y580 sees speed drop to 130 immediately and then it can slowly progress to 1 Mbps until the hardware is all rebooted. Same happens to my Nexus 7, Dell XPS M1530 and to my roku. I have updated to 2.07 (since 2.10 is advised to avoid). And I have attempted changing channels or factory refresh.What Firmware version is currently loaded? 2.07What region are you located?
What ISP Service do you have? Cable or DSL? Cable (link speed independent of internet speed)What ISP Modem do you have? Stand Alone or built in router? Separate Motorola ((link speed independent of modem)What ISP Modem make and model do you have? Does not matter, router issue.If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. Not bridged
Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic. Independent of issue, not a factor
Turn off all devices accept for one wired PC while testing. Wired works perfect.Check cable between Modem and Router, swap out to be sure. Cat6 is recommended. Wireless issue.
View 6 Replies
View Related
Dec 27, 2011
I can't log in to my router settings because my CAPTCHA just displays a red x.to sign up for this forum the CAPTCHA worked....
View 4 Replies
View Related
Dec 26, 2011
The 2 routers are Di-524UP and Dir-655.I have 2 routers and 2 modems,Computer 1 and and 2 are running on the same router as they have low internet usage.Computer usually does large amount of downloading and streaming and requires a separate connection as not to lag the browsing for computer 1 and 2.How could I link router 1 and 2 together so that my computer 3 could deposit files that are downloaded over the internet through wireless lan into my NAS.Or are there any devices that can bridge 2 routers with 2 different network connections over the same lan network.
View 3 Replies
View Related
Mar 20, 2012
I have a dir-825 and wireless clients connected on the 5ghz ssid can see clients on 2.4 ssid and also out to the WAN (internet) but can't see any clients (my NAS ) connected to the dir-825 wired lan.2.4 ghz clients see everything fine. same with clients connected through the wired lan. I've tried DHCP and static ips. no idea what to do next.I was originally on 2.02 fw and have tried 2.03, 2.05 and now 2.06I'd really like to keep the 5ghz on because I have an AP by my tv and several devices connect from there to stream from the NAS.
View 2 Replies
View Related
Dec 15, 2011
How come my 2.4GHz client can't see my 5GHz client? Shouldn't they be visible through the DIR-825 router?
View 1 Replies
View Related
Jan 2, 2013
Im trying to use my DIR 655 as an access point from my new router, which is a TP-Link TL-R860. I've read about every post and blog I can find about this and still cant get it to work. Currently I have a cable running from the TP main router to LAN port 1 on the 655. I then plugged my computer in to LAN port 2 to configure the router.
View 14 Replies
View Related
Feb 8, 2011
have a TP-Link G router, was getting 736kb download, have set up a TP link N (300) but am only getting 560kb download, (my standard BT home hub N was also not as good giving me 640kb download....
with Wired conection results were....
TP-Link G - 752kb
BT Homehub N - 648kb
TP-Link N - 590kb
laptop - Dell XPS, with N wireless
Windows Vista, sp2.
used [URL] to check all the speeds.
why the TP-Link G is so much faster than both the BT Homehub N or the TP-Link N ?
View 1 Replies
View Related
Jan 29, 2012
I have a TP-Link (TL-WR941ND) wireless router in my living room and I want to expand my connectivity to get to the bedrooms area. I have a D-link (DI-524)wireless G router I want to take advantage of. How can I connect the two routers (no cables to be used) together so I can have acces to the internet from my room?
View 1 Replies
View Related
Dec 17, 2011
I'm looking at getting the DIR-825 and currently have the DIR-655 which works great. I was wondering if I can set the 825 as my primary wireless router, but delegate the 655 as an extra "hub" to connect more components to. So I'd like to directly connect the 655 a port on the 825 and have my devices connect to the 655. So the 825 would server internet and so on.
I don't need the 655 as an AP as I already have my media devices connected to my DAP-1522. I'd like to get the 825 so I can use the 5GHz channel for my media devices via the DAP-1522.
View 14 Replies
View Related
Feb 13, 2012
what is the difference between "link aggregation" and "STP"?
For example:
I have two switches connected with two ethernet cables together. Why I will use link aggregation on trunk ports (without load balancing) when STP will do same service?
View 13 Replies
View Related
Jul 3, 2011
The laptop can access either the internet wirelessly – via the internet connected router OR the nas wirelessly – via the second router. [have to change the wireless network that it attaches to.The laptop can also access the desktop, regardless of which of the 2 wireless networks i attach to.My question is, how do i set up my network more efficiently to enable access to all parts of it and the internet simultaneously from the laptop via wireless?
View 5 Replies
View Related
Aug 24, 2012
I have two subnets, that need to share a common link, and each with its gateway at the opposite end. What kind of switch do I need for the two red boxes?
View 7 Replies
View Related
Jan 6, 2012
I've been working on a project which basically is two motherboards running as a single PC. I've managed to remove all of the bugs etc I've found along the way, as well as blowing up a fair few PSU's and am now at the point of having a fully working system. What i now want to achieve is have them both online and able to access remotely via a VNC application. I can already do this for the top board which has a seimens 3G router plugged into it. I can then use the top board to VNC into the bottom board as they are connected on a LAN (just a standard ethernet cable from one port to the other, no hub/switch etc), however this way seems a bit OTT. What i was wondering is if it is possible to link the bottom motherboard to the top one and have them each running off of a different port on a shared IP.
View 3 Replies
View Related
