D-Link DIR-655 :: Web Interface Can't Cooperate
Nov 19, 2011
When I log in to my router (192.168.1.1) refuses to communicate with me in IE8 or Chrome. It seems to work 'OK' with Firefox (not as smooth as it used to up until couple of weeks ago, but still works).I am getting either no response when I click on specific links under STATUS, or a very slow one. I also get no details at all.For example - I click on Wireless where you can see 'Wireless clients that are connected' and nothing appears even though there are at least 5 devices that are currently connected.
View 10 Replies
ADVERTISEMENT
Sep 27, 2012
I am trying to configure a recently purchased Barracuda Web Filter, After adding the IP address, DNS Server, Default Gateway and the new setings, I am now trying to configure my Corporate Firewall..I do not know what Coporate Firewall the manual is reffering too.
View 1 Replies
View Related
Jan 22, 2011
I just bought a new router - Medialink wireless-N Broadband Router model: MWN-WAPR150N I had my PC plugged into the router as a direct connection so I can use my Macbook Pro laptop wirelessly. At first, after resetting the modem (Motorola Surfboard model: SB5101), PC was connected properly as internet was working and same for Macbook Pro. However, the PC connection lasted only for a couple of minutes, more or less before it went "dead". I had it diagnosised and repaired but it wouldn't repair the problem. Each time I reset the modem and router, PC connection was fine but again, "dead" after a couple of minutes.Also, I noticed that after Macbook Pro goes to sleep, when it wakes up, it wouldn't connected either and I had to restart it to get it connected. Macbook is the only one that didn't go "dead" after few minutes, only after going to sleep and waking up.Btw, I did reset the router but no luck in resolving the connection for PC.
View 3 Replies
View Related
May 1, 2013
Search for 'DIR-825 timeout' only returned a half page and none were relevant.
DIR-825 2.03NA - The web interface has a ridiculously low timeout value. 60 seconds maybe?
I can't build a list of MAC addresses, e.g., before it reaches the timeout. I try to save.... and I have to log back in. And my changes are gone.
What's maddening is that it WAS working the way I wanted, with seemingly no timeout, until recently when I had to basically re-do my network.
View 4 Replies
View Related
Dec 14, 2012
i can't access to the router interface page at 192.168.0.1 and not from ddns account. but the internet connection working good, and i'm downloading a lot of torrents in background. i just want to check something on the router and can't access to it, until i disconnect from the power adapter and restart it. maybe he's overloaded or something? how to solve this issue?
View 3 Replies
View Related
Mar 2, 2011
Well, I've been using my DGL 4300 as a switch, but now I need to use the wireless capabilities it has. I tried going to 192.168.0.1 but it timed out. I pushed down the reset button in the back and hold it for 15 seconds, tried the IP again and nothing but timeout. I unplugged the power cable, held down the reset for 15 seconds, plugged back the power, and still nothing. I've tried various methods, various IP's, and nothing.
View 1 Replies
View Related
May 27, 2011
After my dir-655 recently bought the farm, I picked up a NIB 601 at a local computer mall for about $20. The drawback is that "local" for me means that the router is in Chinese.
Is there any way for the web interface language to be changed to English?
View 1 Replies
View Related
May 5, 2012
After uploading dir-615 dd-wrt firmware, it did not lead me to the new page so I unplug it after 5 minutes and replug it. I tried 192.168.0.1 but it seem nothing came out. Then I found that there is no gateway ip address shown up when I use command prompt to search for the gateway ip address. what does that mean? did I clear the software in it?
View 2 Replies
View Related
Jan 8, 2009
The setup:
Time Warner Cable Internet Dynamic IP
DIR-655 A3 Firmware 1.21
3 hard wired, fully updated, virus free, windows xp pro machines
The Issue:When only one PC is running or actively being used there is no issue. However, when there is moderate internet usage on a second pc the internet connection will drop (the WAN light on the router stays on as does the ethernet light on the modem) and give this pair of log entries.
View 14 Replies
View Related
Jun 20, 2011
Bought a new DIR-655 Rev B a few weeks ago.It's web admin interface has failed in some way. The device is still passing all user traffic in both directions, but attempts to connect to the admin interface with my web browser, from both the wired inside and the WAN outside fail. I can telnet to the actual tcp port number that it's configured for and establish a connection, but I can't get any response from it. At this point I'm expecting the only way I'm going to clear the condition is to power cycle the device when I get home from work. It is to note I have the device configured for https for the admin interface. Perhaps that's the more 'advanced' feature that's newer and is exhibiting some kind of bug, I wonder. I'm running the latest firmware available from D-Link.
View 5 Replies
View Related
Feb 1, 2011
My DSC-930L's web interface becomes unresponsive about an hour or two after power cycling my camera. It still responds to pings, and it still sends images to FTP when it detects motion, but I can't log into it via web interface, mydlink, or the iphone app. Power cycling the camera fixes the problem for an hour or so but then its right back to not working again.
View 8 Replies
View Related
Jun 19, 2012
owner of a new B1 here. I've seen various recommendations for 2.03 as a firmware, as mine came with 2.04. Why is this recommended? Is there any others that are recommended?Additionally, after connecting up to the router via ethernet (192.168.0.1), the control mechanism for the router is rather slow. I've owned many routers, and this might be the slowest administration/settings page i've seen for a router. Is this normal?
View 8 Replies
View Related
May 11, 2009
I have a DIR-615 rev C with firmware 3.10 and am trying to setup static routing. There is no option to select LAN for the interface
View 7 Replies
View Related
May 12, 2013
Months ago i can enter in the camera interface by using 192.168.1.100 , its correct ip to enter in the cammera ? Now i dont know what is happening i connect the ethernet cable correctly from PC to the camera and i type in the browser : 192.168.1.100 but nothiung happen ?
View 4 Replies
View Related
Jun 4, 2011
I have bought D-Link DIR-600 router from China and I want to change the web interface language to English.
-Router Info.
-firmware version: v1.03CN
-hardware version : A3
View 3 Replies
View Related
Sep 26, 2012
We are having 7600 with POS interface to connect with an STM-4 link, we are planning to upgrade our link capacity to 1 Gig. Can we do so with our existing inventory or we need any other hardware(WIC)? [code]
View 3 Replies
View Related
Aug 16, 2012
how to open the tp-link interface setup for my TD-W896ON? i have a user and a password but where do i add them ??
View 1 Replies
View Related
Mar 22, 2012
I have a new router. this seems to be a very simple problem relating to the most basic configuration options.
Hardware Version: A1 Firmware Version : 1.01NA
go to SETUP -> "NETWORK SETTINGS"
change "Router IP Address" to 192.168.73.1
change "DHCP IP Address Range" to: 192.168.73.10 : 192.168.73.200
Save Changes Wait for reboot. change my client system's local IP address... so that I can reconnect. direct web browser to http://192.168.73.1/
seen: login page has a select-box for a userid, but no text inside. there is no prompt to ask me to login. I press enter (or whatever... I login). every form interface on all web pages looked at have no labels on text boxes.
I did a view source... and used web-dev tools to look at the page. it looks like the apparent js function, show_words(), is not defined.
change ip address and dhcp address range back to default save changes. wait for reboot. reverse changes to local system things are back to normal. login page has useful text. after logging in, there is something to read.
looking at source again. I see, now, that the js function "show_words" is defined in a file called public.js.
View 5 Replies
View Related
Jun 20, 2011
On our ASA 5510 we already have one ISP link terminated on outside interface. There is correspoinding nat and global configured for outbound access to internet.
Now we need to terminate second ISP link on one of the DMZ interface to have redundancy for the primary ISP.
When primary ISP link or router is down we need to send all the traffic to secondary ISP router. How do we configure NAT and global for this condition that only when primary is down then only this NAT -Global should be used. Do we have anything like object tracking associated with the NAT-global.
So that as long as Primary RTR - object is up ASA will use the first NAT-Global pair. When primary ISP is down RTR-Object is not reachable then ASA will perform the second NAT-Global operation.
Also can we have default route pointing to Outside interface (primary ISP router) and in case of primary router failure it will point to secondary ISP. Do we have "track" in the static route commands on ASA.
View 2 Replies
View Related
May 22, 2013
LINK L2, Between SW4500 and SW6500.
I have experience too much traffic between the link L2 (Fastethernet - GigabitEthernet),, 90%. What can I do to fix that, any command? rate-limit or something?
Here is some outputs of the interfaces:
FastEthernet2/30 is up, line protocol is up (connected)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 247/255, rxload 27/255
Encapsulation ARPA, loopback not set
[Code].....
View 1 Replies
View Related
Oct 30, 2011
I have a problem with System-defined Link Port Interface Utilization Poller. When I generate Interface Utilization Report, this one just displays few Interfaces (see the figure in my attachment). I checked the default poller for interface utilization and recognize that it just associate with few Interface (same as in Interface Utilization Report) instead all. I need to display the utilization of all interfaces in my report
Is Link Port Interface Utilization wrong or Is it necessary to creat user-defined poller that associate with all interfaces of devices?
View 1 Replies
View Related
Aug 8, 2012
All, we have a cisco ISR 2921 router. We want to connect century link dsl via PPPoe on Gigabit int 0/0. G 0/1 is configured for a switch LAN. I think I may have missed a configuration on the router as It is not passing traffic. Do I have to configure anything so that it passes traffic to G 0/1 from G 0/0? Below is the running config
cts#show runBuilding configuration...
Current configuration : 5868 bytes!! Last configuration change at 22:49:20 UTC Thu Aug 9 2012 by ctsversion 15.1service timestamps debug datetime msecservice
[Code].....
View 8 Replies
View Related
Dec 4, 2012
I finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
View 2 Replies
View Related
Nov 28, 2012
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version : 6.0.0 Build 120213 Rel.30335
ISP : ETAPA
I am writing in from Cuenca, Ecuador. I have a TD-W8901G Wireless ADSL2+ Modem Router. I have accessed the interface using the default ip address:192.168.1.1.When I select Interface Setup from the menu, it only shows Internet and LAN as the only 2 options. Wireless is no longer there. It just disappeared! The LED indicator light for WLAN is also "OFF." When you try the Quick Start wizard guide, it cannot complete the setup because there is an IP address error.
I have changed the firmware 2x since, trying to remedy this, I have also tried factory resets at least 3x. Nothing has worked up to this point.
View 1 Replies
View Related
Feb 11, 2013
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 121225
ISP : Online
Recently I replaced my Linksys WRT54G for a TP-Link WDR4300. But unfortunately this did not result in an increased speed.On both the 5GHz and 2.4GHz speed is limited to roughly 2.5-3 MByte/s, which is OK for watching movies etc. but I could reach those speeds with the 802.11g router as well!
I'm using the WDR4300 as access point, so I disabled DHCP server and NAT functionality, left the WAN port empty. And I set fixed IP in the subnet range of my modem/router. (horrible Speedtouch device). All works fine and stable, but too slow.
In the wireless settings I tried the 20 and 40MHz bandwith, disabled WMM, tried to lower the transmission power, tried to set a fixed channel. But all those changes do not have a significant influence on the transfer speed. (both on 2.4 and 5GHz) I'm the only 5GHz access point in my neighborhood, so interference cannot be a problem.
The clients indicate a link speed of 300mbps very close to the router, and this drops to indication of 54mbps further away, but effective link speed remains fairly constant (and stable!) (I find it strange that indicated link speed already drops at 3 meters with clear line of sight to the router)
I did the tests with fixed IPs on two laptops and no devices connected on the LAN ports, to rule out problems caused by the modem/router or other clients.The tests were done using a Lenovo x220 and Asus Zenbook, both with Intel dual band 802.11n wifi interfaces. The Lenovo reaches 22MByte/s via the Cisco access point at my work (with less signal as at home).
View 6 Replies
View Related
Mar 10, 2013
Region : China
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I bought a TP Link router to access internet. Nevertheless the routur interface is in Chinese language which is not convenient for me to set it up.How to change the interface language ? How to upgrade the routur interface to an english one ? (in the website I cannot see firmware for V6).
View 2 Replies
View Related
Feb 3, 2013
Region : France
Model : TD-W8151N
Hardware Version : V3
Firmware Version : latest
ISP : OrangeF
Received today my modem, configured it with some effort but it works... Now i'm trying to save ma config file (rom-0) using web interface, and when clicking on Maintenance > Firmware, i'm always getting:bug.jpg Seems to be a big bug
View 4 Replies
View Related
Apr 9, 2013
I keep getting disconnected from the game "Vindictus". I'm not sure what protocols it uses, but it shouldn't require any configuration on the Router, since it was working fine before. I upgraded the firmware to 4.13 in an attempt to fix the issue, but it didn't work. Some people have suggested "Endpoint filtering" to be set to independent, but I cannot find such an option. Where is the option? I was told it was on the Firewall page, but it is not there (Advanced->Firewall/DMZ). The router is supplied by Virgin Media (ISP) but I'm not sure if that matters.
View 6 Replies
View Related
Nov 12, 2012
Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : TL-WR1043ND_V1_120405
ISP : BT Infinity (1)
I have a TL-WR1043ND v1 with the latest firmware installed TL-WR1043ND_V1_120405.I loose access to the router (can't see web page, can't config, can't restart).I have a Linux server on the Ethernet, and uplink through 200Mbps powerline adapter to the BT Infinity modem. A few other devices on the wireless.The router works well and I prefer it to the BT Home Hub 3 for fiber because it proved to be faster in many cases as tested.But after a few days the web interface becomes inaccessible. It's like the web server died or something. Browser says connection reset, if I try telnet to port 80 says connection refused.Actually I just did a full netcat scan (sudo netcat -z -v -192.168.1.1 1-65535) and all ports say connection refused.Ping works - I can ping it allright.DHCP server works too, just restarted a computer and got IP from the router.Port forwarding works as well and DynDNS seems to work as well as my ISP changes the IP periodically and I can always find the updated one.All works - exept I can't access the router in any way!If I restart (remove power and plug it back in), it boots and I can access the router again.So restarting won't work remotely, I actually have to go home to re-plug it!
View 14 Replies
View Related
Jan 18, 2011
I have two 3750 switch.switch A(main) and switch B is connected by OFC but i have another wireless link for backup.Now if OFC goes down then i manually connect wireless link with switch B for this reasons i am faceing a lot of problem. I want without any changing of cable if my primary link goes down then my backup link automaticaly goes up and vice versa .
Switch-A port gi1/0/9 and Switch-B port gi1/0/9 is connect by OFC Switch-A port gi1/0/8 and Switch-B port gi1/0/8 is connect by Wireless link (backup) i attach my network diagram kindly find the attachment file.
View 3 Replies
View Related
Dec 19, 2010
We want to terminate new 10M link via Ethernet interface on Cisco 1841 router. We have free Gig port on the router. We also have HWIC-FE module inserted in the router. However, our implementation team said that Cisco 1841 doesn't support 10M link. It is not designed to cater to such high Bandwidth.
View 14 Replies
View Related
Jan 3, 2013
My SRP527W has never had its firmware upgraded since purchase. I had a need to do this recently, but could not find the section under Administration for Firmware upgrade.The only two items under Administration are Time Setup and Switch Setting.I've tried different browsers, to make sure that was not an issue, with no success. Any direct URL to the modem web interface that might allow me to update the firmware. url...Otherwise is there another method using a USB stick or tftp or similar?
View 1 Replies
View Related
Feb 17, 2013
-Region : Poland
-Model : TD-W8951ND
-Hardware Version : V5
-Firmware Version : 5.0.0 Build 120522 Rel.23978
-ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
View 2 Replies
View Related
