How To Set Password D-link Dwl-2100

May 29, 2011

i have a dwl-2100 access point. first can this be used as a regular wireless router, and second, i tried the, and connection got reset a few times, so what else can i do to set out a pswd?

View 2 Replies


Cisco :: Changing Password On WLC-2100?

Aug 31, 2011

I am currently running WLC - 2100 with software version :
My question is :
How to change the existing password ( not reset )  but change the password with the web interface ?
If that cant be done, then my guess is I have to do it via telnet/ssh session

View 4 Replies View Related

D-Link DCS Network Camera :: DCS-2100 - How To Change From Wired To Wireless

Feb 13, 2011

I'm trying to re-setup this EOL camera on a new router.I've been able to reset the cam to factory defaults and see it wired using dhcp.  I then was able to change the address to a static address, still wired and still can see it with IE.  However when I disconnect the rj-45 cable, power down and restart, I can't access the cam.

View 2 Replies View Related

D-Link D-ViewCam :: Older Cameras Like DCS 2100 / 3220 Not Fully Supported

Feb 17, 2010

Downloaded DVIEWCam 3.0. Are there any plans on supporting older Dlink Cameras like the DCS-2100 etc ...?  Even my DCS-3220 is not fully supported, however the 3420 worked in the config menu.

View 3 Replies View Related

DLink DWL 2100 CD Missing?

Jan 2, 2012

How do i setup my d link dwl 2100 ap at my new address. I have moved and my installation cd has gone missing. The install wizard wants to work off the cd

View 2 Replies View Related

Cisco :: How To Integrate WLC 2100 With ACS 5.0

Jan 17, 2011

i have a cisco ACS version 5.0, I need to authenticate a wireless users connected to WLC 2100 controller when i connect the controller to a Dot1x port in the switch , the port go down.

View 6 Replies View Related

How To Switch On Wireless On Compaq 2100

Oct 10, 2012

How to switch on wireless on Compaq 2100

View 1 Replies View Related

Cisco :: ICMP / SSH With LWAPs Behind WLC 2100

Feb 27, 2011

I'm new to the Cisco WLCs and recently implemented a wireless infrastructure using a WLC 2100 with 1262 LWAPs. I have two of the 1262s plugged into ports 7/8 using crossover cables. They're functioning correctly with the exception of the inability SSH and send pings to the LWAPs behind the WLC. Is there anyway to ping/shh through the WLCs to the LWAPs behind it? I use an NMS (Nagios) to monitor the status of the LWAPs and it can't monitor them if it cannot ping them. Also, is there anyway to configure the WLC to monitor the status of LWAPs?

View 2 Replies View Related

2100 - Killer Nic Dropping Connection On LAN

Mar 13, 2013

I have a Killer Nic 2100 installed on an 1155 setup under Windows 8. I can upload large files to anywhere on my home network .. but when I pull large files off of my main computer with the Killer Nic in it .. the connection drops out on my main rig... no network connection of any kind on my main rig until I reboot ..

I don't have this problem with the onboard nic ..

sometimes the network will drop when the power flutters .. all the other computers I have will have internet connection .. but my rig won't ..

View 15 Replies View Related

Cisco Wireless :: Getting 3500 AP To Talk To WLC 2100

Jul 18, 2012

I am trying to config my wireless lan controller (WLC) 2106 to discover my new 3500 access points.I followed the example Cisco configuration doc.69719.I am using a Cisco 3760 switch to interconnect the AP and WLC.I set up DHCP in the switch. [code]

View 6 Replies View Related

Cisco Wireless :: WLC 2100 And LAP1131AG Are Disconnecting

Oct 10, 2010

Since few days the WLC 2100 series controller and 3x LAP1131AG are getting disconnected and the controller gets offline via the local ip address.  At that point I have to reboot. To get anywhere and after I connect wirelessly to the AP before I know it it disconnects.  It worked for 3 years straight no fuss. And now nothing. I reconfigured the WLC 10times and no diffference.  


View 6 Replies View Related

Cisco Wireless :: To Join 1262 With Wlc 2100

Apr 1, 2012

I have a cisco AIR-LAP1262N-A-K9  and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?

View 1 Replies View Related

Cisco :: Unable To Access GUI For 2100 Series WLC?

Sep 2, 2012

I have powered ON WLC(2100 Series) and connected LAN port from WLC to my PC. To access WLC GUI what is the factory default IP address?
I connected Console Port of WLC to Serial port of my PC. I have configured WLC as per the WLC quick guide.

Management Interface IP address ::
Management interface Net Mask:

The result is same even when below commands are used Configuration modeport adminmode all enablenetwork webmode enablenetwork secureweb enable 

View 12 Replies View Related

Cisco Wireless :: LAP1142 Cannot Join WLC 2100

Apr 2, 2013

I'd WLC 2100 series and 9 access point LAP1142N .8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142  is can not . Part of LAP  is AIR-LAP1142N-A-K9
Apr  2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found
*Apr  2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found
*Apr  2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr  2 10:52:42.284:  status of voice_diag_test from WLC is false
*Apr  2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller


View 4 Replies View Related

Cisco Wireless :: Recommendations For Implementing A Second WLC 2100?

Jan 3, 2013

We have two 2100 WLC's that support 12 access points. One has been sitting in a box for some time, but we're at the point where we need to add additional access points that will put us in excess of the 12 limitation. What is the best way to go for installing the second WLC?

View 2 Replies View Related

Cisco Wireless :: WLC 2100 Series DHCP

Sep 1, 2011

I have a problem with our WLC 2100 series (2125). Basycally internal DHCP server configured on WLC is not working. I have one AP connected to port no 7 (PoE) to bypass and eliminate problem with other equipment.
Port no 7 details:
IP Address:
Default router:
DHCP Server:

View 14 Replies View Related

Cisco :: Can Import A Config From A 2100 Wlc Into A 5500 Wlc

Feb 14, 2012

I just got a new controller (5508).Is it wise to try to import my 2100 config into the new Hw our should I start from scratch?

View 4 Replies View Related

Cisco Wireless :: WLC 2100 Configured To Control Two AP

May 17, 2012

I have a fairly simple WLC 2100 configured to control two APs. We had a power outage a few days ago, and though the WLC was on a surge protector, it did not come back up properly after the outage. The STATUS light sticks at amber and I can't get any console response. At this point I'm not sure what to do except replace the WLC, though I'm loathed to do that as our budget was just cut substantially for next year and we're trying to turn nickels into pennies.

View 4 Replies View Related

Cisco :: Setting Up Wireless LAN Controller 2100?

Feb 7, 2011

I am having trouble on setting up a WLC2100 ver 7. we need to implement a private and public network. private network authenticate to IAS - RADIUS (windows server 2003 server) while the public network is open but when a client connect to AP it will redirect to a 3rd party web athentication - HotSpot Server. the challenge is we want to broadcast a single SSID.

1. when a user/guest connect to the AP a radius server will authenticate thru IAS - Radius.

2. when a user is authenticate via radius a dhcp server will give an ip address of the private network.

3. if the user is not authenticate a dhcp server will give the public ip address and netowrk traffic must go to a different VLAN.
my question is, is it possible to broadcast a single SSID for the two network? is there a document which is related to our scenario?

View 2 Replies View Related

Cisco Wireless :: Internal Temperature WLC 2100?

Dec 17, 2009

The operating temperature for 2100 wireless lan controllers is up to a miximum of 40 degrees celsius according to the datasheet. We deployed some 2112 controllers all displaing a temperature above 50 degrees celsiun. This during normal operation and deployed proper enviromet (aroco ...)

View 2 Replies View Related

DLink WL-2100 - PC To Access Point To Wireless Modem

Apr 2, 2011

I have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?

View 2 Replies View Related

Upgrade Or Add WPA To WEP On Intel(R) PRO / Wireless Lan 2100 3B Mini PCI Adapter

May 5, 2012

Can I upgrade or add WPA to WEP on Intel(R) PRO/Wireless Lan 2100 3B Mini PCI Adapter

View 1 Replies View Related

Cisco 2100 - Data Not Sending Or Receiving From Modem?

Oct 26, 2012

I'm using Cisco 2100 cable modem. It worked fine until some time later where the Data Send & Receive LED's stopped blinking. A man came to check if the cable was the problem by replacing it, but it wasn't. He claims it might be related to the laptop. I have tried several times restarting it. (I'm using mobile broadband) I would really like fast rather than slow internet ( I was limited so now it's slow but free)

View 14 Replies View Related

Cisco :: WebAuth Bundle Not Uploading 2100 Series

May 19, 2012

Recectly we replaced Cisco 2100 Series LAN controller to Cisco 5508 Wirless LAN controller , I downloaded WebAuth Bundle from my Old LAN Controller ,when i am trying to upload to my New Wireless LAN controller ,its not uploading and also it gave me uploading failure error message .

View 2 Replies View Related

Cisco :: 2100 Can Create A Guest User Directly On ISE

Oct 10, 2011

I have an instance of ISE and NCS with a WLC 2100 plus a couple of LWAPs. This is an evaluation POC lab to sell ISE and NCS to our management to make our life easier.The problem I have amoungst many is I can create a guest user directly on the ISE and the guest can login, the ISE monitor shows the guest authenticates but the clients webpage passes them back to the login page not onto the original client url. The web auth is pointed at the ISE/guestportal/portal.jsp page.If I point the web auth at the internal WLC page using a WLC local user account it works.If I set the guest access to pass through it works without issues getting dhcp and dns. On the ISE is there a policy needed to say if guests are web authenticated give them access? The need is for AD authenticated users to be able tocreate guest users. The AD authentication works for sponsorship and guest creation its just the guest access redirection I am having issues with.

View 1 Replies View Related

Cisco Wireless :: WLC 2100 Per-user Bandwidth Contracts

Aug 16, 2011

One of our customers have one Cisco WLC 2100 (firmware 5.2) with 4 AP Mesh 1522, in a city deployment. In order to achieve local regulatory, has to implement bandwidth limitations per user.
I got screen captures of WLC QoS Profiles options, with Average Data Rate in Per-User Bandwidth Contracts. So my question is, do I need any other equipment to achieve per user bandwidth limitation? Can it be done with WLC QoS options?

View 3 Replies View Related

Cisco Wireless :: WLC 2100 Ipv6 Ready Connection

Apr 30, 2012

We have a 2100 cisco Wireless LAN Controller which manages 3 APs and  assign IP address to clients which connects via wifi.  Currently, we are  deploying dual stack IPv6 and our consultant stated that our current  controller does not support IPv6.
This is rather odd statement because there is an option to enable IPv6  in the advance tab of WLAN.  And sometimes clients (win7 and Mac OS X)  are getting v6 addresses, able to ping v6 sites, and reach v6 sites  successfully.   And other times, clients do not..or getting the v6  address for 10-15minutes, then unable to ping/reach v6 sites.
Our consultant is sticking by his words saying it does not support.   If  this is true, then clients should not be able to get v6 at all....not  sometimes and not other times; very inconsistent.
And what is ipv6 pass through? What is ipv6 bridging?

View 2 Replies View Related

Cisco Wireless :: 2100 / 1130 / 3550 - Couple Of APs Are Down

Feb 27, 2013

I have a couple of AP's that are down and won't let me change to up. When I try to enable admin status I get a pop up window: " error in enabling admin status". 
I have configured the WLC for power injectors with a 3550.

View 2 Replies View Related

Cisco :: 2100 WLC - Guest Access / Passing AD Credentials

Aug 31, 2011

We have a building with 6 Cisco Airnet 1140 connected to a Cisco 2100 WLC, all tied into a nice Central Certificate server and a Win2008 NPS/Radius server on a Win2008 AD. Our trusted PC wireless access is fine, with domain laptops with certificates authenticating with DHCP all round the building. We use GP to apply settings to an AD integrated Proxy server for internet access.
The problem I now have is with guest access...
We are an education establishment, so students could turn up with anything from a laptop to an iPad to an Android phone, which immediately rules out using proxy PAC files to configure the proxy.
What I really want is a method of using the radius to verify the guest user against their existing AD user account, which I believe is possible. The one snag we have is in order to avoid the user having to configure the Internet proxy we would have to switch it to a transparent mode, which immediately restricts our ability to report on AD username, we would only have an IP address to report on, which is next to useless!
We've looked at a Gateway product (Astaro), which integrates the Filtering onto the Gateway, but the downside is that you have to use their APs, so we would be replicating existing work, whilst also managing two filters.

View 1 Replies View Related

Cisco LAN :: 2100 - Browser Access To Wireless Controller?

Jul 29, 2012

I have a wireless controller 2100. I can't access it via browser, when I am connected to one of its physical ports. I use the same subnet ip address as that of the management interface of the wlc.

View 5 Replies View Related

Cisco :: 2100 / Two Network Connections And One Wireless Controller?

Jan 29, 2013

In the near future my company is looking into the option of adding a second network connection (exclusively for customers visiting our facility) to our pre existing WLAN network. We are currently using a Cisco 2100 series Wireless LAN Controller and probably 6-8 APs. Our main connection is made up of 4 T1 lines and the second connection will more than likely be a cheap DSL connection. I'm wondering if this technology supports two separate connections on one controller and APs. For example, is there a way within the controller web interface to separate what is currently our "Guest" connection from the main Internet line? I was thinking of just plugging from the DSL router directly to the controller and save the hassle of changing routing and VLANs.

View 12 Replies View Related

N150 - Centrino Intel Pro Wireless Lan 2100 3a Won't Connect To Netgear

Apr 28, 2011

Dell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...

View 1 Replies View Related

Cisco :: How To Chance Web Authentication Certificate On WLAN 2100 Controller

Feb 8, 2011

how to chance the web authentication certificte on WLAN 2100 controller. My users are complaining that they need to accept the security certificate before proceeding to the actual authentication?

View 4 Replies View Related

Copyrights 2005-15, All rights reserved