I have just purchased a WAG120N and E4200 Router.I would like to use the WAG as modem only and leave all network activity to be managed by the E4200.i have an ADSL2+ service through iiNet.All of my home harware is wireless.Has anyone completed this setup, or know how this might be achieved.Full Bridge mode on the WAG is my obvious thought but the specifics have me a bit confused.
View 2 RepliesI was using Linksys ADSL router ( WAG120) as modem router. Recently I bought new Linksys x3000 and installed a modem router in place of WAG120. Now i would like to connect the both routers to get the signals in first floor of my house.
View 9 Replies View RelatedI am connecting the E4200 to a Sonicwall TZ100. I want the TZ100 to assign IP addresses to devices that connect to the LAN via the E4200.
How do I have the E4200 act as a WAP only or not assign IP addresses and push that responsibility to the TZ100?
I'd still want the E4200 to have a SID key for LAN access security.
I have XP 64bit OS and I can't seem to get the setup CD to install E4200 Router. I have looked at the FAQ and it says it should be compatible with all Windows OS. Is there a link out there to the drivers I need to do this?
View 1 Replies View RelatedI use my e2000 as router and want to use the e4200 as repeater. so if i connect wireless to my e4200 i can see all my devices also the one on the e2000. How to setup the e42000 ?
View 5 Replies View RelatedHave been trying for the past two days to install a new E4200. It gets to 25% in the setup and then errors out and says I need to contact customer service.
Connecting through a brand new DSL modem that I know works as I can get access through my old router.
My PC (Windows 7) is directly connected to the router. I got to the point where I named the router in the install process the first time, but then it hung.
Have tried to use the CD to re-setup with no success. I've tried the hard reset holding in the button for 10 seconds and unplugging but nothing has changed.
Our internet provider has no intention of providing a IPv6 DNS so I have a crippled at best service. We live in an area where our only option is through satellite service, so changing providers in not in the cards, yet.
If I "Disable" the DHCP Sever, the setup menu provides a method for me to force feed up to three Static DNS addresses, all with IPv4 addresses.
There are several locations that provide "free" DNS service, but how does one verify the security of such sites? Does Cisco keep track of the status of this kind of service or am I on my own? Cisco seems to endorse two DDNS services, but for home use, the extra charges seem otherwise unnecessary, and do not yet address the IPv6 question.
The first few that I have investigated that do provide IPv6 service also provide their addresses in IPv6 format. The E4200 menu does not seem to allow me to do that.
Am I going to be forced to live with crippled IPv6? I have already discovered a software product that has failed since changing routers, but works if I take my laptop to a particular WiFi location.
how to setup the E4200 so that I can access the media server when I am in office? I was browsing on the Cisco website and unable to find it.
View 8 Replies View RelatedI've got an E4200 at my house. I'd like to know if it's possible for my to establish a VPN connection from a remote location to login to my E4200 to get access to my computers behind the firewall.
View 1 Replies View RelatedI just purchased e4200 from a friend of mine. Got an issue with setup of this device. I use a model from internet provider. Have 2 computers at home. One is pc with cable, another one mac with wireless.SO my issue is that i can not connect none of them. I was trying to use cd that comes with router but he can not locate a router. When I connect cable directly from modem to computer everything works fine. As soon I connect cable to a router I can not see a router and I can not connect to internet.
View 1 Replies View RelatedSo, with the latest firmware update I could add a second e4200 to my network to use as a bridge or access point? What I need is another device in my living room that can pick up the wireless signal and dish out network connectivity to my receiver, xbox360, and ps3. With the new firmware update can this be done with a second e4200? How does one connect to each e4200 on the network for setup (dohave to change the default ip address of 1?)I just bought a trendnet TEW-687GA 450 mb/s wireless gaming adapter and a trendnet 5 port switch to accomplish what I mentioned above. I'm just wondering if there is an advantage to switching over to two e4200's. The trendnet adapater does not have a 5ghz channel.
View 2 Replies View RelatedI got a problem with my setup main computer, It work wery god wireless, with very fine speed about 82 mbit in and 24 mbit out. The problem is that it almost don't work at all with cable, even if i turn off the wireless network, the speed is about 2-3 mbit in and about 6-7 mbit out All other computers, tv. printer wireless work very fine.
View 2 Replies View Relatedif it is possible to access a modem setup page with a E4200 router? My router is on 192.168.254.200 and modem(WAG-200G) is on 192.168.254.100, ethernet cable is on internet port on the e4200 and on port1 on the modem. Modem is set is bridge and I set up a ppoe and dhcp on router. Everything is ok, except that i can not access modem setup page to see adsl conection speed and settings.
View 1 Replies View RelatedTrying to setup port forwarding for an XBox 360. Set fixed IP on XBox using IP outside DHCP range. DHCP range is .50 to .80. Set XBox to .49. Gateway is .1. Mask is 255.255.255.0.Added four port forwarding rules per directions on xbox site and also portforwarding.com for ports 53, 80, 88, 1074 to the static IP Turned off DMZ, Turned off UPnP, Turned off SPI. Windows firewall is on, running XP Pro SP3 and Win 7 Pro on other devices.Making the rules active for the fixed IP shuts off internet access for other devices.Single router (E4200 V2), switch, then remaining devices. Private IP addresses in the 192.168.xxx.xxx range. Rebooted router, same issue. What am I missing?
View 9 Replies View RelatedI'm pretty new to networking. Purchased a E4200 for my home line. When i connect directly through the modem i see speeds of about 600mbps but when i connect through the router via an ethernet cable on an empty port on the back of my e4200 my speeds drop to about 180mbps. I expected a speed loss going through wireless but why i am experiencing a speed loss by using the ethernet as a passthrough? I thought the ethernet ports on the e4200 were gigabit and support up to 1000mbps?
View 1 Replies View RelatedI am finally duffing my WRT 610N (N=Never consistent in performance) main router and WRT54G that I am using up in my shop as an expander. Now I am going to a E4200 Main Router and E3000 for my secondary router (Truthfully a dual band expander).
Am I going to just simply Flash my 610 to default , disconnect it and pack it away , Setup my new E4200 , Plug in my E3000 into port 1 and go about giving it a separate IP Addy? Or can I expect a **bleep**? Any setup tips?
Wirelessly I am running 2 laptops , a PS3 , Xbox 360 , Epson printer , a picture frame and Samsung Blue Ray and TV, and on occasion 2 android phones. On the Wired side (Ethernet) I have a Sling Box , a Desktop , and the router up in the shop. This is the normal load and never everything all at once (Although it has been done).
Have high speed cable and find that the wireless speeds using Speedtest.net are faster than when hooking directly into the E4200. Do I have something set incorrectly?
View 3 Replies View Related[URL]I have a Linksys E4200, even if i put wireless on manual WPS is still working, any answer from Linksys?
View 5 Replies View RelatedI do not have a "storage" tab in my setup screen. I have Setup, Security, Wireless, etc. According to its manual there must be a Storage tab between security and wireless. Mine doesn't have it. USB drive is connected and I see "mywag320n" on the network but I can't access it because it requires login and password (which I guess I must set up from Storage tab )
View 8 Replies View Related1) I dis abled the DHCP services on modem router as i was connecting it to a belkin router and after that i cannot accesss the setup of the WAG 120N.
2)If I acces the WAG120N by Lan the internet works fine but if i acces through wirless it does not.
3)Also when ever i connect the LAN cable from BELKIN router to WAG 120N the wirless services stop as well on the BElkin router and i cant figure it out why.
How do I set up a password to secure my home wireless network. Gate is on a XP desktop. Just have my Vista notebook on network. Use WCG200 gateway which was given to me by relative who has upgraded.
View 6 Replies View RelatedI can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
View 1 Replies View RelatedI have a existing WiFi ADSL router and I have a WAG120N lying spare in my closet. I recently shifted to my room a floor above. I wanted to amplify signals as the current router is not able to beam signals that far. Hence I wanted to set this up as a WiFi repeater to have a complete coverage. I tried N number of ways but could not succeed.
View 1 Replies View RelatedI lost my CD that I used to do to setup the internet for the router.
View 4 Replies View RelatedI need to setup some port forwarding on my X3000 to pass through the firewall to my server but cannot find the relevant page in the setup GUI.
View 2 Replies View RelatedI have a Linksys WAG200G wireless ADSL router. So it has one ADSL(phone) line input port , 4 Ethernet ports and wireless router. My router is fine and works well on ADSL connections. But as I have switched to Comcast DOCSIS modem based internet connection now, I want to to setup this router as "Home Gateway" only and not the modem. My intention is to use- use 1 of the 4 ethernet ports at the back of router as an INPUT . I want to put the ethernet output of the DOCSIS modem into this INPUT- and then i want to use the remaining 3 Ethernet ports as OUTPUT ports from the router.- I also want to work my router as Wireless router.
My query is- Is this possible ? Basically use 1 port as an input and 3 as output.- I have tried different things - Using Bridge mode only. DHCP disabled but sometimes only wireless works and other times only LAN bridge setup works but both do not work together.- Also at times, one Ethernet port will work as an INPUT and 1 as an OUTPUT but other two remain disabled.
I am trying to setup a vpn tunnel on my AG241 router but not having too much luck. I am not on a static ip, i sort of get the feeling that as long as i know the current external ip address i should be able to get through to my xp machine with the shares on it.
View 7 Replies View RelatedIs it possible to setup a router to router connection over the internet with fixed IP Addresses with two WAG320N?
View 3 Replies View RelatedI'm trying to set up access restrictions to specify the full url on my WAG200G (firmware 1.00.07). In particular to block a few specific https:// sites without blocking all https://. It it easy with http:// If I try https://blah.com it throws back an error invalid url.
View 3 Replies View RelatedI have a Linksys X2000 modem. Sometimes I see the "Wi-Fi Protected Setup" button glowing orange (amber?) for no apparent reason. The manual says that it "blinks rapidly in amber if an error occurs" but I don't think any device is trying to connect wirelessly at the time. How can I determine if there is a problem?
View 5 Replies View RelatedI upgraded my router Linksys wrt54g to Linksys x2000. I was able to install the equipment with no problem, my problem is with the Linksys Advisor. When I open the adviser it goes to setup wizard, I get a screen that tells me to disconnect my old router which I have done. The next screen gives a list of routers to select from my router x2000 is not on the list. How can I get passed this screen? So I can use the adviser to set up other computers and printer.
View 1 Replies View RelatedI've been trying to get into the web interface for my AG300.
I keep getting the "Problem Loading Page" dialogue - the address has not been changed from the default 192.268.1.1
So far I have tried it in Windows & Ubuntu, and in Firefox, Chromium and Explorer. I have sone a hard rest and rebooted it and the computer numerous times.
if I ping that address there is no result, but I obviously have internet access.
I tried already several times, may be I entered already a name and password, can`t remember. Anyhow this time I was well documented to start again, but after 192.168.1.1, leaving 'name' blank, and password 'admin', this was quoted as wrong name and/or password. What to do to be able to continue now?
View 2 Replies View Related