I am trying to setup a vpn tunnel on my AG241 router but not having too much luck. I am not on a static ip, i sort of get the feeling that as long as i know the current external ip address i should be able to get through to my xp machine with the shares on it.
View 7 Replies
This is an interesting and don't know where to begin.From factory reset I connect a latop to 192.168.1.1 and change the IP address to my subnet 192.0.1.5/24. I disable DHCP too.THen i plug it in to my LAN and I can ping 192.0.1.5 but can't http to 192.0.1.5
So I remove from LAN, connect to my laptop, manually change my laptop op to 192.0.1.4/24 and then my laptop can http to the AG241 on Linksys AG241.Is there anything on the AG241 that could be confusing my LAN?
Im having a bit of trouble, how am i supposed to update my router, i have DLed the tarballs from GPL and now im not sure how to update it, do i have to makefile? (im using ubuntu by the way which is handy if i have to build it!) and if i do have to makefile how do i do it?
View 2 Replies View RelatedI'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.
View 1 Replies View RelatedI have Linksys AG241 ADSL router. i have a IPSec vpn client installed on my laptop, so can i connect AG241 & access the hosts behind AG241?
View 1 Replies View RelatedI lost my CD that I used to do to setup the internet for the router.
View 4 Replies View RelatedI recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
View 2 Replies View RelatedIs it possible to set up a vpn tunnel on a 1721 router that uses the following ios:
c1700-y7-mz.124-13b.bin
I thought I had read somewhere that tunnels were not supported on the 1700s but wanted to make sure. If they are I would like to know if they are supported in the above ios.
I do not have a "storage" tab in my setup screen. I have Setup, Security, Wireless, etc. According to its manual there must be a Storage tab between security and wireless. Mine doesn't have it. USB drive is connected and I see "mywag320n" on the network but I can't access it because it requires login and password (which I guess I must set up from Storage tab )
View 8 Replies View Related1) I dis abled the DHCP services on modem router as i was connecting it to a belkin router and after that i cannot accesss the setup of the WAG 120N.
2)If I acces the WAG120N by Lan the internet works fine but if i acces through wirless it does not.
3)Also when ever i connect the LAN cable from BELKIN router to WAG 120N the wirless services stop as well on the BElkin router and i cant figure it out why.
How do I set up a password to secure my home wireless network. Gate is on a XP desktop. Just have my Vista notebook on network. Use WCG200 gateway which was given to me by relative who has upgraded.
View 6 Replies View RelatedI have just purchased a WAG120N and E4200 Router.I would like to use the WAG as modem only and leave all network activity to be managed by the E4200.i have an ADSL2+ service through iiNet.All of my home harware is wireless.Has anyone completed this setup, or know how this might be achieved.Full Bridge mode on the WAG is my obvious thought but the specifics have me a bit confused.
View 2 Replies View RelatedI can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
View 1 Replies View RelatedI have a existing WiFi ADSL router and I have a WAG120N lying spare in my closet. I recently shifted to my room a floor above. I wanted to amplify signals as the current router is not able to beam signals that far. Hence I wanted to set this up as a WiFi repeater to have a complete coverage. I tried N number of ways but could not succeed.
View 1 Replies View RelatedI need to setup some port forwarding on my X3000 to pass through the firewall to my server but cannot find the relevant page in the setup GUI.
View 2 Replies View RelatedI have a Linksys WAG200G wireless ADSL router. So it has one ADSL(phone) line input port , 4 Ethernet ports and wireless router. My router is fine and works well on ADSL connections. But as I have switched to Comcast DOCSIS modem based internet connection now, I want to to setup this router as "Home Gateway" only and not the modem. My intention is to use- use 1 of the 4 ethernet ports at the back of router as an INPUT . I want to put the ethernet output of the DOCSIS modem into this INPUT- and then i want to use the remaining 3 Ethernet ports as OUTPUT ports from the router.- I also want to work my router as Wireless router.
My query is- Is this possible ? Basically use 1 port as an input and 3 as output.- I have tried different things - Using Bridge mode only. DHCP disabled but sometimes only wireless works and other times only LAN bridge setup works but both do not work together.- Also at times, one Ethernet port will work as an INPUT and 1 as an OUTPUT but other two remain disabled.
Is it possible to setup a router to router connection over the internet with fixed IP Addresses with two WAG320N?
View 3 Replies View RelatedI'm trying to set up access restrictions to specify the full url on my WAG200G (firmware 1.00.07). In particular to block a few specific https:// sites without blocking all https://. It it easy with http:// If I try https://blah.com it throws back an error invalid url.
View 3 Replies View RelatedI have a Linksys X2000 modem. Sometimes I see the "Wi-Fi Protected Setup" button glowing orange (amber?) for no apparent reason. The manual says that it "blinks rapidly in amber if an error occurs" but I don't think any device is trying to connect wirelessly at the time. How can I determine if there is a problem?
View 5 Replies View RelatedI upgraded my router Linksys wrt54g to Linksys x2000. I was able to install the equipment with no problem, my problem is with the Linksys Advisor. When I open the adviser it goes to setup wizard, I get a screen that tells me to disconnect my old router which I have done. The next screen gives a list of routers to select from my router x2000 is not on the list. How can I get passed this screen? So I can use the adviser to set up other computers and printer.
View 1 Replies View RelatedI've been trying to get into the web interface for my AG300.
I keep getting the "Problem Loading Page" dialogue - the address has not been changed from the default 192.268.1.1
So far I have tried it in Windows & Ubuntu, and in Firefox, Chromium and Explorer. I have sone a hard rest and rebooted it and the computer numerous times.
if I ping that address there is no result, but I obviously have internet access.
I tried already several times, may be I entered already a name and password, can`t remember. Anyhow this time I was well documented to start again, but after 192.168.1.1, leaving 'name' blank, and password 'admin', this was quoted as wrong name and/or password. What to do to be able to continue now?
View 2 Replies View Relatedi'm facing a big problem with my access point WAG54G ver 2.0 ,i just bought it from 2 days but i find alot of problems when i start using it ,i have read all the user guide and the quick install to see how to setup the access point and make it work with my adsl.i have configured all things right using PPPOE and putting my user name and password and then save settings then go to the status and press on connect , but it don't connect with me just i find connecting and adsl link : Down and still making connecting and nothing after that and my adsl led is off haven't any colors ,and when i get again to basic setup i found the password that i put it in the ppoe login is too long , not my password i tried to see what is this password and recover the hidden i found it " d6nw5vlx2pc7st9m ".i don't know what is the problem i tried alot of times to change setting and also the same problem.i think that it's a frim ware problem and i tried install a new updated frimware but everytime trying to install it get installing and suddenly stoped and white page appeard and all the access point is stopping and when restart it the ac power.
View 3 Replies View Relatedi have a cisco DPQ3925 , im trying to setup user access for my kids to prevent them from accessing the net , i have set up the time of day and the user setup , but cant get it so u have to logon with the set user names to access the net.
View 3 Replies View RelatedI've been having problems with the router portion of my cable modem router. I have a brand new router that I would like to use rather than the crappy router that is part of the cable modem.The problem is that I'm not able to get online no matter how I set the settings. I have disabled DHCP in the cable modem router and am connecting this to the router thru the internet port of the router.
View 12 Replies View RelatedIm trying to setup a cable modem which is also a router that has a printer attached to one of its lan ports. From there it connects to another router which connects to other clients from there i have another router with a VPN connection with other clients. I would like to be able to see everyone on the network. How do I setup the routers in particular the router with the vpn which is the last router. Also the vpn router is connected through its WAN port to the router ahead of it at its lan port so it can use its VPN connection.If it makes it easier lets ignore the cable modem as router and ill find the printer another way of connecting but essentially i need the two other routers for two ip addresses. One for the first router with my regular IP and then the other is for VPN IP.
View 3 Replies View RelatedI have one interface setup to a Cisco 2921 router connected to a Cable modem.DHCP is on the 2921.when I connect to the ssid for my guest i'm redirected to the authentification portal 1.1.1.1 .i'm putting valide credential and when pressing the submit button .. it just go anywhere.
I have setup another SSID with a psk and it's working fine.. getting ip and able to browse internet.From what i have read... it's apparently DNS issue on my router.. but what should I check.
I have a WAG160N wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.
What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ?
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies View RelatedI have two Cisco 2941's going over a IPSEC VPN. I need to push the same network over this connection. For example i need 192.168.255.0 / 25 on my side and i need to plug in a laptop on the far end 2941 with the same network. I have built GRE tunnels before and i found a configuration online to brdige interfaces over a GRE tunnel.
when i get to adding the bridging to the configuration which i will show below i get an error. Please see below. Also when i try to add the same briding command on the GRE tunnel which is needed it doesnt show the bridging command as being available. The Cisco 2941's are both using version: mwr 2941-iprank9-mz.124-20.MRb1.bin.As i stated the only end result i need is to be able to configure a path from point A and B and have the same network on each end.
I have succesfully config an IPSec VPN Tunnel by using a Router Scientific Atlanta Cisco 2320 and a RVS4000 4-Port Gigabit Security Router with VPN.On the site of Router Scientific Atlanta Cisco 2320 this is some info: [code] On the site of RVS4000 4-Port Gigabit Security Router with VPN this is some info: [code] Remember that you can not be on the same range of IP, I mean, you can not have 192.168.0.X if the remote network is on 192.168.0.X, you have to change some of the Routers.I show the configuration on Router Scientific Atlanta Cisco 2320: I show the configuration on RVS4000 4-Port Gigabit Security Router with VPN:If all is correctly configured, you should see on Router Scientific Atlanta Cisco 2320 the Status Connected:
If all is correctly configured, you should see on RVS4000 4-Port Gigabit Security Router with VPN the Status Up.As you can see, I'm connected to the remote Router (RVS4000 4-Port Gigabit Security Router with VPN) by my own web browser accesing by the local IP 192.168.0.10.I have used Authentication MD5, maybe is not the best one but I had no time to test SHA1, I will when I will have time.
I am trying to setup a VPN tunnel between a Cisco ASA 5510 (Version 8.2(2)) and Sonicwall TZ200. I got tunnel up and going and I am able to ping the Cisco ASA internal IP from the Sonicwall LAN but nothing else works.
When I try to ping a host behind the Cisco ASA from the Sonicwall LAN I get the following message "Asymmetric NAT rules matched for forward and reverse flows;
[code]...
I just joined this company and they already ad a VPN to one of their partners that provides them access to some resources. We have now added a 2nd location but the partner wouldnt allow a 2nd VPN tunnel so the decision was made to give the new location a ASA5505 to tunnel thru the main office to access the resources at the partners site.Using ASDM i believe i was able to setup the tunnel to the main office but there is no resource there to use. Now i'm stuck and i do not know what to do to get to the partner site
View 4 Replies View Related
