Linksys WRT54GL Firmware With Error Logging?
Aug 11, 2011
Cox Communications comes into the house over an RG6 cable to a a 2-way splitter, one leg amplified for TVs, the other leg straight to a Linksys BEFCMU10 cable modem for internet access. The modem is connected to a Linksys WRT54GL router for the PCs.
BEFCMU10: Hardware Version = v1.0; Software Version = v2.0.2.0.7
WRT54GL: Hardware Version = v1.1; Software Version = v4.30.11
The WRT54GL firmware is stock Linksys code which can log addresses but not errors (as far as I can determine). Is there a WRT54GL firmware lump I can flash into my device that logs network errors it encounters between itself and the BEFCMU10 and that it might be informed of by the BEFCMU10 in its dealings with Cox? I'd want to read that log through the WRT's web UI; ideally I'd want to upload it to my PC. If the firmware logs errors on/from its other ports as well.I need it to sort out what Cox tells me are numerous "modem resets" that they're seeing at their end.The resets are the apparent cause of big slowdowns, we see on our end.By the way, yesterday a Cox tech replaced the 2-way splitter and the short coax from it to my modem, then measured signal strength and said it was in the middle of the "okay range".
View 4 Replies
ADVERTISEMENT
Jun 20, 2012
Have a few of these routers internally as well as at various clients. The incoming and outgoing logs show up blank, even when there are 10-20 computers using the Internet and I know there is traffic being generated. DHCP and security logging still works fine. I also have a few E1200s on the latest firmware that are logging just fine... I'm just having issues with the E2500s.
View 6 Replies
View Related
Aug 29, 2006
I am attempting to setup a wireless access pointand want to deny access to a group of IP addresses. When I go to Wireless, MAC setup, Deny or Allow, and select "Edit MAC Address List" my browser crashes. I have tried this on two different Linux systems and three browsers, Firefox, Mozilla, and Seamonkey.Tech Support tells me to downgrade to Firmware version 4.30.2, the only compiled version available on the Linksys website, but with no way to go back to 4.30.5 if the problem isn't fixed or if worse problems come up I am reluctant to try this fix, The only other suggestion Tech Support offered was to replace my WRT54GL with a WRT54G.
View 3 Replies
View Related
May 30, 2007
It appears that there is no firmware I can download for my WRT54GL Version 1.1. While it may never have been updated from what the router came with from the factory, it would still be useful to have it available. In my case, I would like to revert the router from the DD-WRT firmware to factory specs.
View 3 Replies
View Related
Jun 2, 2011
I flashed my WRT54GL with firmware for a WRT54G and now when I go to the configuration page all I see is this: url...I have tried doing a hard reset by doing the 30/30/30 and by using tftp to try and send the correct firmware. The hard reset does not work and the tftp keeps timing out and not sending anything.
View 1 Replies
View Related
Oct 3, 2011
I just bought my DIR-825 from Frys and it came stock with 2.02NA B1 firmware, but everytime I try to update it to 2.03/2.04/2.05/2.06 it errors saying it might not be the same hardware or something on the lines of that. But now when I try to upload it, it just leads me to "192.168.0.1 was interrupted" and can't even get to the error screen now.I'm not too savvy when it comes to routers, especially a D-Link since previously I had a Linksys WRT54GL
View 15 Replies
View Related
Aug 24, 2012
I have an E3000 with firmware v. 1.0.01 build 6. I am trying to upgrade to the latest firmware version. I downloaded the file, and when I went to install from the web page I got the error message: Not enough memory available. I tried from 2 computers and got the same message.
View 6 Replies
View Related
May 14, 2012
Notified of new firmware for my router. Tried to install. Downloaded fine but will not install. Keeps saying error but not what kind, how to fix, not anything.
View 1 Replies
View Related
Jul 3, 2012
I have an EA2700 which I am trying to rollback to the older interface, however it errors out every time I try to install the firmware.All I ever get is this message: Unexpected Error The firmware update did not complete successfully. Please try again later.We've encountered an unexpected error. If the issue continues, please visit our Technical Support site.I've reset the router multiple times, powered it off overnight, re-downloaded the file multiple times, and am still unable to successfully rollback. Sometimes it even errors out when I try to set the password on the router itself and I have to reset it again before I can use the interface.
View 9 Replies
View Related
Sep 20, 2011
I have an WRT54G2, and I recently bought an new notebook and a new mobile phone. The question is none can connect to my wireless network.My linksys had the following configuration:
Firmware 1.0.03
SSID hidden
WPA2 personal + AES
My note is an ACER 5552-5664 running Ubuntu 11.04 and Windows 7, in Ubuntu I can’t use the wireless. In Windows it works fine.The phone is a Samsung Galaxy and do no connect in the wireless.I had an old notebook running only Windows 7 that works fine too.In my father’s home there is an WRT54G and all my equipment connected there. Other problem is that when I tried to update the firmware, it simple don’t update. I’ve downloaded the last firmware file from Cisco’s page.
View 3 Replies
View Related
Jul 15, 2012
I have been getting the logs in my cisco 6513 switch [code] On further investigating in the module 9 which has a DFC card also , we found the source of this error whether it is a source of any upcoming potential impact or can be simply ignored
View 3 Replies
View Related
Sep 13, 2011
I have a Linksys WRT54GL Router. I'm open to getting another router if it won't suit my needs.Which firmware should I install?Which version/build of the firmware?Any additional modifications I should make to the firmware?
Requirements:Connect an external hard drive to the router, so that any devices connected to the router can access files from the hard drive.Run an FTP server (with SSH) on the router, so files on the external hard-drive can be accessed from anywhere.Run VPN, so that certain computers can access the hard drives over VPN.Run a BitTorrent client on the router with the files stored on the external hard drive.
View 2 Replies
View Related
Aug 14, 2011
I have upgraded the firmware on my Linksys BEFSR41 V4.3 router. On this router i used Statis IP (so DHCP enabled). This worked fine on my network, until this upgrade. Now when i try to ad another static IP , or when i want to change something in the Routing-tab, i get this message ' Wrong Gateway Input! It should be the same subnet with WAN IP'. Strange because i haven't changed anything in the settings.I already did a complete reset on the router, still the same problem.
View 7 Replies
View Related
Nov 16, 2011
I'm encountering what I think is an issue on logging system on FW ASA 5520 - Asa Version 8.4(2), ASDM version 6.4(5). When I disabled the logging inside a rule from ASDM, or from console with the "log disable" option inside ACL, If I check in ASDM logging real time window I continue to see all the entry related to disabled rules. This is a correct behaviour about ASA logging ? How I can "hide" the entry related to disabled rules (this is what I need for troubleshooting purposes) ?
View 1 Replies
View Related
Sep 2, 2012
I get this error when I update to 1.12. Error 324 (net::ERR_EMPTY_RESPONSE): The server closed the connection without sending any data.
View 3 Replies
View Related
Aug 24, 2012
Firmware 2.07NA for version B1 units contains two bugs:
1 - An underscore in the Device Name causes a cryptic "37" error to appear when attempting to save any changes to the network settings. Version 2.03 allowed the underscore character. Other invalid characters, such as a "-", generate a more meaningful "Device name given is invalid" message.
Removing any underscores eliminates the error and allows settings to be saved.
2 - The upgrade breaks SharePort communications; the SharePort client utility cannot see the USB port on the device after upgrading from 2.03 to 2.07. This occurs with the latest 3.1.0 R 1 Utility (SXUPTP Driver: 3.4.6.0).
Downgrading back to 2.03 is a workaround.
View 1 Replies
View Related
Feb 15, 2013
I am using DIR 615 Hardware Version JX... When I check for an update to FIRMWARE I get the following message, "Did not get information".In the past when I clicked on there may be a firmware update on our site. I was taken to [URL] which gave me an 401 error and now redirects me to the US d-link page. Which doesn't even list Rev Jx as an option.I am having a lot of trouble with this router in regards to VPN and must have in China, and am hoping an update is available. [code]
View 1 Replies
View Related
Jun 17, 2012
One of our customers wants to update the firmware of a 5508 wlc, but always gets the following error message: Error Message %UPDATE-3-INV_FILE_SIGN: Error! Invalid image signature!. Image may be corrupt.but the same image works fine on another 5508. The update was downloaded via a smartnet for the wlc, on which the update works fine. does the customer has to download another image for the second controller, or should the image work on both wlc?
View 1 Replies
View Related
Jul 6, 2012
This morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1. Numbers could be off slightly since i'm going from memory. I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades. I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.
View 3 Replies
View Related
Mar 15, 2011
DIR-655 RevA4 - upgraded to 1.35NA, which is shown on http://192.168.0.1/
When I try to re-log in as Admin, I get a message of invalid password. I have unplugged to reset, but still cannot get back in.
View 3 Replies
View Related
Dec 25, 2011
first one had to get rid of because just wouldn't work with a 3CX server, anyway, I have a DIR-655 A4 factory shipped with 1.32NA I am trying to update the firmware to 1.34NA but it will not let me. It keeps saying Code:
View 6 Replies
View Related
Aug 26, 2010
I have been trying to update my boradcom 5709c firware, or more acurrately trying to install the Broadcom Network Device firmware, family version 5.2.7 from the drivers page for my PowerEdge T110 running Server 2008 R2 Enterprise x64. Once the package extract and starts running, I am getting an error that simply says "BMAPI Error", and the program bails out. I really need to update this firmware, and have been looking for manual steps and other ways to get it done and have come up short.
Any other ways to get the firmware to update.
View 5 Replies
View Related
Aug 14, 2012
Yesterday I tried to install c2960-lanbasek9.mz.12.55.SE4.bin onto my router. When I changed the boot commands, I did not leave the 2nd option in there and the old firmware has an .ex3 extension. After trying to boot to this new image, we receive a looping error message that continues to reboot and go through the same process.Basically the error is "ERROR: firmware not supported by hardware"I have power cycled it a few times but durning bootup, I never see the ################## which would allow me to BREAK sequence and get into rommon. The device simply waits about 30-40 seconds after boot and goes right back to the looping reboot sequence and the error message. Is there any hyper term or putty settings to change on this?
View 1 Replies
View Related
Mar 11, 2013
I'm looking for a tool that will let me log traffic from my Linksys router. I'm interested in seeing which devices are access thing internet from my home and to see what kind of bandwidth they are pulling down.
View 3 Replies
View Related
Dec 15, 2012
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : 120926
ISP : ADSL24
Just bought new router TD-W8968 and tried to do a firmware upgrade to latest version but keep getting Error code: 4503
Have even tried an older version thinking maybe I had to do that one first but got same error code.
View 3 Replies
View Related
Mar 19, 2013
I bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies
View Related
May 10, 2012
A new Cisco 3750V2 (WS-C3750V2-48PS-S) running IOS 'c3750-ipbasek9-mz.122-50.SE5.bin' waspurchased to add to a stack of 3 Cisco 3750 (WS- C3750- 48PS-S) switches. The IOS on the stacked switches is 'c3750-ipbase-mz.122-25.SEB4.bin'.I loaded this IOS on to the new Cisco 3750V2 and deleted its original IOS. Boot up failed with error 'hardware not supported by firmware'. I am now trying to follow the recovery procedure but the I can only initialise the flash (flash_init) and there is no 'boot_helper' command to load the boot helper files. There is no option to rum 'copy xmodem' so I cannot upload the original IOS image via xmodem on hyperterminal.
View 7 Replies
View Related
Jun 11, 2011
I am using firmware version 1.0.04 build 6.I am having a few issues viewing the log; the incoming, outgoing and security logs are completely blank, the DHCP log is the only one populated.Even though it's populated, the time stamp displays the date as Jan 1 1970, time appears fine if I use UDT (Time is set to Mountain), the Router Status correctly displays the current time for my location.I vaguely remember the other logs worked with a previous firmware 1.0.03? Don't recall if the Date Time stamp was working correctly.
View 2 Replies
View Related
Jan 22, 2011
Does MAC address settings allow the administrator of the router to prevent access of computers and devices to a network at will? Basically, in my household I need to have remote control over wireless devices and allow them to use the network at times and others disable it. In other words, I control when and if a certain device has the ability to use the network or not. I think I found the settings in my router when I log into it, but I'm not sure how to use them or if it even does what i described above.
View 1 Replies
View Related
Jan 7, 2013
I'm thinking of switching to another ISP which is faster and cheaper than who I'm currently with. Only problem is they have data caps. Any way to log inbound/outbound traffic usage with this router so that I can make sure I'm not going to hit monthly limits?
View 5 Replies
View Related
Jul 1, 2011
I have Linksys WRT54GL wireless router on the top floor so the devices in one part of the bottom floor (most away from the source) are having trouble staying connected let alone getting good connection. What would be good solution in my case? I'd like something wireless, don't want to drag cables downstairs.
View 2 Replies
View Related
Sep 4, 2012
I upgraded my router Linksys wrt54gl with dd-wrt and i can't connect to internet now. It was all good before. Im hitting my head fo past 5-6hours and cant figure it out.
View 1 Replies
View Related
Jan 24, 2011
I have a zhone dsl modem/router. When testing at shields up I pass all tests 100% - stealthed ports until I add the Linksys. Then I get 4 open ports and all my stealth ports change to closed.
Set up:
Internet ---> Zhone (only 1 ethernet port out) ---> Linksys (internet input) -> PC
[URL]
Should I be running firewalls on both? Would flashing with Tomato or dd-wrt fix this?
View 2 Replies
View Related