Netgear WGT624 V4 - Power Surge - Computer Can't Connect To Wireless
Jul 13, 2011
After a quick power surge forced my desktop to reboot, it can't connect to my wireless network, even though everything else can. It may have been applying windows updates at the time of the surge.
Earlier today I shut down my computer to apply some windows updates. A few minutes after it rebooted a power surge knocked it out for an instant and the computer rebooted again. I don't know if it was done applying the updates but for some reason it can no longer connect to a wireless network. It keeps saying "unknown reason" when it fails to connect. I think I had a static IP attached to it.
My iPhone and iPad can still connect to this network, but this one computer can't. It's a desktop running Windows Vista Home Premium with a broadcom adapter added to it. It's too far away to connect to any wired connection. My router is a Netgear WGT624 v4.
I don't think I can post any IPconfig information here because I'm forced to type this on an iPhone.
There was short power surge ( for a second only), and after that my laptop lost connection with home network. To be more specific, only one laptop lost connection, two other and iPad have no problem to connect. I brought laptop to the store where I purchased it 12 days ago, and there it worked. Brought it home - same thing, it can not connect to home network, and keep getting message that password is incorect ( and is not). Finally, I replaced laptop for completely new one, ant sill have the same problem: can not connect to home network a nd when brought to the store -it works. Of course I did that drill with connect/disconnect modem, router, pc's more than one time.
I recently upgraded to an EA3500 router using Cisco Cloud Connect after my E2700 series router was damaged after a power surge came through coaxial cabling to my house and was transfered to the router over ethernet.
I have my EA3500 running both 2.4 and 5 GHZ networks running as 802.11n only and a Lynksis WRT54GS router for 802.11g network devices that are left in my house connected to the EA3500 over ethernet.
Since upgrading to the EA3500 - I have noticed that I am having some trouble with my internet connection dropping randomly that was not present when I was running the E2700 series using the same configuration.
I have not been able to get my full internet speeds as promised by Comcast over wireless (30 Mbps - using direct ethernet I can get upto 40Mbps). My two printers connected via ethernet through an ethernet bridge are being stubborn, the IP address constantly changes. I have not changed any settings in the router other than the network name and setting it up for dual band configuration.
Moved into my grandparents for the time being. They have a DSL network...not sure how fast, but it seems very slow. I got a new computer and had to download CS:Source again over steam. It took all night to download and now when I try to go find servers none show up
They have a tiny motorola dsl router. Not sure on the model number as some of the numbers o the sticker have faded away. I hooked it up to my Netgear WGT624 v3 wireless router via the gygabyte 54mbps wireless pci card.
Can I test the connection to see if it is capable of running online games? I've got my iphone 4 hooked up to the wifi and it runs fine...same with this computer web surfing
recently a Cisco 3560E switch went down due to a power surge. the switch is getting power but i am only seeing the below message continously. it is keep on rebooting. i try to reset to factory settings/ safe boot nothing worked. is there any way i can bring the switch up or it is hardware failure.Using driver version 1 for media type 2Base ethernet MAC Address: 00:23:33:af:1b:00Xmodem file system is available.The password-recovery mechanism is enabled.Using driver version 1 for media type 2Base ethernet MAC Address: 00:23:33:af:1b:00Xmodem file system is available.The password-recovery mechanism is enabled.
I want to share mobile broadband with another computer.One desktop running on windows7 and connected to wireless router netgear wgt624 v3 via ethernet cable. The other laptop is running on windows7 and has wireless card. Both computers are connected wirelessly via router on private network within workgroup and can share files between each other. The mobile broadband dongle is connected to desktop pc and desktop is running the internet Now I want the desktop pc which is running internet by wireless dongle to share that internet with laptop via wireless router. I have tried setting is up but couldn't do that. When I connect the dongle to desktop pc it use the same IP address 192.168.1.1 which is already used by wireless router. Tried to configure different IP in router but didn't work.
aptop ,i just buy wireless netgear router for wireless net range but it does not work .its saw me the router acess point but some how my internet not connecting . its connecting with linsys but not with my router. its something which i can do ? am thinking of security system on the netgear properties
I have got a TP link wireless router connected by TP link power line ethernet adapters connected to my sky box, one to Samsung Smart TV, which both work fine the third I have connected to my computer. This shows up as as a local area connection but with no internet access. I have similar problems to other people with internet access dropping out after installing Windows * and had hoped an ethernet connection would be more stable. Any thoughts on why I can't connect to the internet via my powerline adapter.
I try to maintain a sizable network at my workplace. We have 10 desktops, 3 laptops (sometimes more) 4 printers/fax, etc.etc. I have just ordered a new HP Pavilion Slim-line S5000 Series with Windows 7 Pro. I cannot get it to connect to the Network. I have set up the server (which runs windows server 2008) with an account called "communications" I have named the computer "communications". I go to the system and security>system: computer name,domain, workgroup settings>change settings. I enter all the information correctly, and it tells me it cannont find the network path. This is happening on this brand new computer, and our old dell optiplex 760 (running windows vista pro). We use a netgear pro-safe 24 port 10/100 switch hub, and a linksys wireless G broadband router model WRT54GS.
i load windows 7 onto it and try to get into internet explorer to get google chrome and it says that i need to configure a network so i try and configure one but it says that no networks are connected to it.i had vista on it before windows 7(still couldn't connect)and it said that it was a realtak router but underneath the router it says that it's netgear i don't know which one it is.i have gotten into the router using its ip.also the model for the netgear part is b90-755044-15 it work just fine for this computer although it's on windows XP do i need a driver for the mother board,router,or what.
I have cable broadband internet. My internet modem is a Ubee D3.0. It is connected to my Netgear N600 Wifi router which have my computer and DirecTV hooked up to it via ethernet. My wifi went down the other day. Devices were connected, but were not getting any internet service. In troubleshooting, I attempted to dial in to the router using www.routerlogin.net as well as 192.168.0.1, and I could not get into the router. I assumed the router must have crashed, and I only purchased it a month ago, so I took it back to the store and exchanged it for a new one. I got home and plugged it in, still not working. I can't access it using the above mentioned methods, and the setup software does not detect a router present. I unplugged the router and hooked the computer up directly to the internet modem. Still no luck. The computer does show a network connection in the system tray, but with no internet. I plugged my laptop in to the internet modem, and I am able to get internet just fine from my laptop. I even did a system restore to a restore point last week when I know the internet was working. No luck.
1. Our Motorola SB6120 popped out of existence today; FYI, this was plugged into a brand new APC UPS unit (which does not have coax/cable suppression features).
2. Previously (past days), one interesting thing I have noticed is excessive amounts of distasteful electrostatic shock when working in the closet and touching the metal bearings of the cable & wires. Is the cable not grounded properly, and is it the cause of #1?
Recommend me a surge protector/suppressor strictly for cable (do not need outlets/ethernet/rj45/etc).
I have a Netgear wireless router that is connected to my desktop in my house to broadcast wireless throughout. However, the main computer is hooked up to an ethernet cord for a hardwired LAN connection. For some reason, my desktop will constantly disconnect from LAN and switch to wireless, back to LAN to wireless etc.
I'm using a Netgear WGT624 Router for my firm's intranet. At home I'm using a router called NSW-R2 by Gembird..
What I want to do is connecting my PC at home (Windows XP) to my firm's intranet so I can print on my LAN Printer or edit files on my NAS.
I've heard about VPN tunnels, but I don't want to keep my firm PC on 24 hours a day. So is it somehow possible, to build a VPN or something similar by only using the Netgear WGT624 Router?
Edit/More Information: I've steup a DDNS. My Router supports Port-Forwarding. I'm currently using Remote Desktop. Both PC run Windows XP Professional.
Have two other computers that connect with ease to the Netgear wireless router, but the new computer will not access the internet. I have been searching for answers and have tried about everything I can find nuder similar posts, but I still have not internet access. At varying times, I have had "internet access", but no actual ability to load websites. Right now, I do not even have access. I am at a loss.Even at my low level of experience, I am usually able to tinker until I fix the problem, but I am about four hours in and currently seem to have taken a step backward. I cannot even begin to explain what things I have already tried
I have a NetGear WNR-1000 wireless G router. I currently only have 1 computer hooked up but I have had 3 computers hooked up to it before. It doesn't matter what internet it's connected to or how it's connected to the modem itself. I have had DSL and Cable hooked up to it and I am currently using it as a secondary router behind my roommates old Wireless B router. He currently has all of his things hooked up via ethernet and wirelessly to his router. So, im download the xirrus wifi inspector thing. It doesn't matter the OS either. I've had XP sp3, vista, and 7 all hooked to it and it's the same all the way around and it doesn't matter the kind of wireless card either!
I am trying to add a new computer to my wireless statione access list but have not been successful. I got the ip address of the computer i was trying to add, my issue is how to add it to the list. i tried adding the details and filling in the device name and MAC address but kept getting the error message "invalid MAC address.please enter again.
I have a Netgear CGD24G Wireless Gateway and a Gateway MA8 laptop with after-market Windows 7 (Vista got a virus, went ahead and upgraded.)Now, when I download 100 MB files on my Xbox 360 (Which is wired to the modem) it will be downloaded in a couple minutes, or less. The other computers in my house (There are plenty, and even more that come and go.) get a blazing internet connection, and most of them are wireless.Now this computer, which had an extremely quick connection as well all of a sudden dropped off, while the rest of the computers remain fast.I've gone to Speedtest.net before and after this occurred and my speed before was around 12 mb/s, and one time around 4 AM was even upward of 25 mb/s, all of these tests were performed multiple times on different server locations. I JUST did the speedtest, and it came back with .4 mb/s, and the UL speed was 2.0. I honestly can't remember what I averaged with it prior to the problem, but it was definitely higher as well
I have a NETGEAR XAVB101 Powerline AV Ethernet Adapter and an AMD Llano build HTPC which refuses to work with each other.
The power plug works well with my Gateway NV79 laptop and even my Intel Core i5 -2500K desktop, without any problems! I have also used it to connect to my Roku, Yamaha Network Receiver and other networked stuff and all worked great, just the HTPC seems to have issues connecting to the network!
The HTPC is AMD A6-3650 on a ECS FM1 A75 Mobo with Integrated Realtek RTL8111E Gigabit Ethernet Controller, which is what I am connecting the power plug to! Only the connection over the power line adapter does not work, it works great with both a connection directly from the router and with wireless!
The adapter has a 128 bit encryption push button security feature which I'm NOT using. When I connect it the HTPC tries to connect and fails and shows the network as connected to an unidentified network. My LAN drivers on the computer is all up-to-date!
I have a Netgear N150 Wireless ADSL2+ Modem Router(DGN1000) which i need to connect for wireless access..My internet connection is a wireless one(antenna connected on roof) connection available to only one computer with an RJ45 LAN.Is it possible for me to connect the router to this LAN cable and get internet on more than one computer at a time?? I have the following information
IP : Subnet : Default Gateway : Primary DNS : Secondary DNS : MAC of the Registered Computer :
I have two computers. The first is a laptop running Vista and connects to the internet just fine. The second is a desktop running XP. I have a network adapter on the desktop and although it DOES find my network, I cannot get it to connect to the internet. I type in the correct passkey and it just goes on trying to connect, saying that it is acquiring a network address but no connection
I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
My fianc just reinstalled Windows XP Home Edition last night as his computer was virus-ridden and it was becoming impossible to use. It took a couple times for the computer to even pick up the Windows disc, but fourth time lucky and it was good to go. Once reinstalled we tried to get everything checked and download some anti-spyware etc, but it wouldn't pick up the router. The router is wireless, but connects to his computer via a cable. The router is a Netgear 54 MPBS Wireless Router, DG834G v3. We have been told that the computer should just automatically pick up the router, but the only way it will allow us to try and connect is via a dial up connection.
I was upgrading the firmware of the WRT54G router when the notebook´ screen closed and it went to standby mode. It was sttoped the upgrade process.Now only the ports and Internet LEDs light up, but the power LED is off.I also cannot connect to the navigator for show the administrator´s window. What is the procedure to recover the operation of the router in a situation like this?
We had a power outage the other day, and now the wireless router cannot connect to the internet. Network Magic shows there is no connection from the device to the internet. I tried repairing it through Network Magic but it wasn't able to fix it.
My PC is directly connected to the wireless device by LAN cable. If I connect the PC directly to my DSL router I can connect to the internet, but not if I connect to the wireless router and from there to my DSL router. I tried resetting the wireless router to factory defaults and then going to [URL] and resetting up the router security settings. But Network Magic still shows the bad internet connection.
I then tried resetting the router to factory defaults again and installing it from scratch using the setup CD but that failed as well. I'm not at home right now so can't remember exactly at which point it was but I think it was either when the setup wizard tried to detect the device or install the device.This is the second time I've had to reset up my router due to power outage. Last time I was able to get it working by doing the first steps above.
I have 3 computers wired to a Netgear R6300. Two of those computers (both running XP SP 3) I added new LAN Gigabit Cards (Tenda TEL9901G) . One recognized the card right away and had no issue connecting to the Internet (using this computer now). The other shows a 1.0 Gbps connection but I can not get any web pages to come up. I can access other computers and devices on the network without an issue on the computer that doesn't connect to the Internet.
If I type in the web address it says "Server Not Found." If I type in the IP address it will come up with the name of the site in the address bar but it still says "Server Not Found." I've tried several times to unplug the router and modem (Motorola Surfboard) and restart everything but the problem was still there. Also, I tried other Ethernet cables and no change. The LAN card drivers are up to date but I don't think the card is the issue since I swapped the new cards (to see if the card was the problem) and it does show a 1.0 Gbps connection. Also, tried uninstall/reinstall, disable/enable the card many times.I didn't change any setting in the router after installing the cards.Here is the ipconfig output:
For some reason I cannot ping or FTP on a specific computer on my home network. All other computers work fine and the specific computer works fine on other networks. But the combination of this computer and my home network it doesn't like.
I have disabled both windows firewall and my virus software but nothing seems to work. It seems to be a timeout issue as FTP and ping sometimes does work but FTP is increadibly slow when it works and the ping time is very high 670ms and above. I am running windows 7 and my router is a netgear n150
I have an E1200 and if a device - such as my tablet or laptop - is left unused for a period of time - say for 4 or 5 hours - they won't reconnect to the router unless I do a power cycle/reset on the router.
Child at college having significant connections issues with Sony VAIO VPECB trying to connect to Netgear N300 wireless router. Upped the bandwidth - no impact. Other MACs in the house have no issue.
i am trying to connect my netgear wgr614 v7 wireless router and i can't do it. i have the actiontec m1000 modem which is thru qwest i have read the setup manual available online on how to setup the modem with the router but it just doesnt do anything?
