I have recently purchased a PS3 and can sign into my PSN account but cannot access PSN when i try to play games on multiplayer.My university doesn't allow routers so I was wondering if:
1)Having a router would let my ps3 work properly online?
2)How to set up a router without it being detected.
What are the list require for setting up Data Center for either University or Government?
View 4 Replies View RelatedSo I can't seem to access ANY site related to my university (www.concordia.ca) anymore from my home network. I've tried to visit URL or any of its' sister sites from my desktop, my laptop, my iTouch, even my ps3, I've also tried cross-browsing to no avail. I've checked the router page, apparently my Hardware Version is B1 and my Firmware Version is 2.00NA. Access Control is unchecked and there are no sites at all listed under Website Filter. I've also tried resetting using the reset-hole and also by pulling off the power chord. Also did a factory-reset from the router page, the problem persists despite all of that.Every other site works just fine, it's just my university site that refuses to load up. I've browsed the last 7-8 pages of this forum, this doesn't seem to be a common problem based on that little sample. So what gives exactly? I used to be able to visit those sites just fine prior to few days ago.
View 8 Replies View RelatedI have recently installed a new motherboard (Gigabyte X58A-UDR3R) and i've been having a problem where when i plug my ethernet cable in to my on board lan nothing is being detectedOn start up the with the cable plugged in the ethernet light will flicker letting me know its being detected then randomly shuts off when i reach my desktop. This happens and i dont have a connection to the internet
View 1 Replies View RelatedThe building's IT specialist has provided a program I think he made himself which changes a computer's settings to allow the user to log on and enter their student username and password in order to connect to the internet.Usually, when I get back from his place, I:plug in my Ethernet cable,open network and sharing center open the properties for my wired connection go to authentication and untick 'enable IEEE 802.1x authentication'and this works fine. However, I came back from his house two days ago and this did not work. I've tried system restore multiple times, rebooting, unplugging and plugging in the cable, and even going back to his house, setting myself up there and coming back to test if I can get back to normal again.
View 2 Replies View RelatedI was connected to my university's network through VPN from my personal computer. All websites are routed through their servers. Many people connect and use the network.I forgot to turn the VPN off and went to an xxx website. Actually I watched a video on megavideo. Then I realized the VPN was on and turned it off.My question is, can an automated system determine what I did and will any IT person go ahead and click the link to see the video?
View 1 Replies View RelatedI want to setup a DC++ HUB for sharing data within the university local network. We have addresses of the form 172.31.*.*. These addressed are accessible within the university bu non routable outside on the internet. My plan is to setup a local HUB for DC++ for sharing data within the university intranet. So even if internet is unavailable data can be exchanged through LAN. This HUB must not be accessable outsied the university network.how should I do this all..implementing network sharing other than DC++. My basic idea is that everybody can share their data and the data is searchable from one common interface( Web interface is better option, if possible). And data featching should prefferably be from many hosts, using multiple connections so that speed can be improved..
View 4 Replies View RelatedI currently have my wired cable internet hooked into my wrt310n. I have that hooked into a linksys 10/100 ef3124 switch. From there, I have cat5 run to the back of my house, where the wireless signal is weakest. I've got an E2000 router and would like to hook that in at the back of the house. What settings do I need to make in order to set up a completely new wireless network in the back of the house?
View 1 Replies View RelatedDoes the E1000 router come with a default security setting upon installation using the supplied CD?
View 9 Replies View RelatedI have a very large house with many people using wireless laptops. i used to have verizon internet and I purchased a wlan 11g mini router from radio lads. After it was set up it worked great. I have just switched to comcast internet (my first mistake) and I can't get the mini router to work.
View 1 Replies View RelatedIf i want to setup a router and switch in my small business... 11 computers. Can i run 2 switches into one router or is it better to run one larger switch into one router. Second is when I set it up do I need to assign addresses to each computer or do I just need to plug them in and setup the network with windows network wizard. I will have a shared drive on one of the computers or possably some network storage.
View 1 Replies View RelatedI'm often on my university WiFi, which is unsecured. I have a new ASUS router that supports a VPN network, so I've created a VPN network and it seems to be working-- I connect to the VPN through the unsecured WiFi and I can see my home computers on my network.I want to tunnel all my internet browsing through the VPN, for security, but when I'm on my VPN, I can't browse the internet. I understand that I can go into advanced settings and set it up so that I'm on the VPN while still browsing on the unsecured wireless (I think that's called split-tunneling), but that seems to defeat the purpose. I think I have to set up port forwarding, or maybe a DNS server...
View 1 Replies View RelatedA friend of a friend has a business with 8 computers (3 lap tops) and then desktops. He uses Verizon. I have no idea about how to set this up correctly but, would like to try.He got 2 Linksys routers and asked if I could get them to work on his network. I said I'd try.
There are NO INSTRUCTIONS -
do they go to the "boss computer" and then? I just don't know and feel too stupid to say I'm not sure.It's probably very easy but, it's been years since I've worked on Networks.
i want to set up my wireless router it is currently set on a static ip but i want to set up in pppoe(username/password) mode i set up once in pppoe but internet is not working?
View 7 Replies View Relatedi have verizon DSL. Their newest router, the westell 7500, and their older one, the westell 327w. I want to setup a home network. I have heard there is a way to have these 2 routers connect wirelessly (one threw the other) so that i can hook up direct tv dvr to the internet w/out running a long cable.
View 3 Replies View RelatedSETUP CD MISSING - NETGEAR WNDR3700v2Have just received excellent condition 'barely-used' WNDR3700v2 router with ac adaptor, but NO setup cd. Am I dead in the water, as Netgear doesn't provide replacement CD's, or is there a workaround using say, an early firmware upgrade? Or other?
View 2 Replies View RelatedI am trying to setup a wireless router in my dorm but I cant seem to find any solid guide on how to do it. Simply plugging it in to the ethernet port provided in my room doesnt do it. It seems I have to configure it, but I dont know where to begin.
View 6 Replies View RelatedI've just bought a TL-WA701ND so that I could connect my TV to internet via this AP using client mode. However, when I tried to configure the AP into client mode by following the user manual and instructions, I failed in the last step where I need to ping the router IP address (192.168.1.1). It returned "Request Timeout". Configuration of my AP is as shown below and I make causing it couldn't ping the router.
LAN configuration on PC:
TCP/IvP4,
IP address: 192.168.1.150
[Code]....
Setting up a linksys router with dsl Modem.laptop direct to modem works router connected dhcp to laptop Eth. port 1 OK router to modem dhcp does not generate DNS but appears to give IP address. Result: can't connect to internet / diagnosis says cannot resolve ( google.com or yahoo.com etc.)
View 2 Replies View RelatedI have a Cisco RV120W Wireless-N VPN Firewall that provides wireless access to my small business employees. How do I provide customers and guests to the building with wireless access to the internet, while restricting their access to my network?
View 3 Replies View RelatedI bought a N150 belkin router from a friend without the quick installation guide that was supposed to be incuded. I tried to set it up myself using the CD-Rom but wasn't able to so my roomate did it with the CD-rom she had. She didn't know how to put in a password so I was able to connect my laptop by pressing the WPS button on the router. Now I want to connect another laptop but I need the security key. How do I set one up?
View 2 Replies View RelatedHow to put password on my router wifi
View 3 Replies View RelatedI want to setup two WIFI network with one Router at home.
View 2 Replies View RelatedJust purchased a Linksys wireless router without realizing that it comes with a start-up CD and of course my Dell netbook does not have a disc drive.
I thought about bringing my laptop home from work and but then would I then always have to lug it home each night in order to use wireless in my apartment?
A pen test has shown I have crackable transform set on my firewall. I can see the config this relates to and do have higher encryption available. What I dont want to do is remove it until I know my remote sites are not using it.does any one know a command that shows all the policies/encrption in use?
View 5 Replies View RelatedRecently they bought a new Cisco 2911 router and told me that they want it connected to an outside WAN connection that they hadn't used in a while so they could create a little network on the side. They want to just plug the server into the router and go. Unfortunately, I am sort of clueless about how to set up the config for it.
There are 3 GE ports, with the line from the outside coming in on GE0/0. I've already activated the interface and it is up, but that's where I get stuck.
I need to increase my wireless speed higher that what Uverse gateway is supplying. Want to install a 802.11 N router behind the uverse gateway and disable the uverse wireless. Uverse gateway will allow this.
View 4 Replies View RelatedI have a siemens gigaset567 unit.I suspect others are accessing via vlan.
View 1 Replies View RelatedMy router was working just fine when a lightning struck. I cant seem to connect to the router's configuration page (192.168.1.1) anymore, All the lights on the router are on and I tried to reset it to default settings several times but still it wont connect. I tried it on a laptop but I still cant get it to connect. I can surf the net just fine when using the ADSL modem though. I can ping the IPaddress 192.168.1.100 but can't ping the default gateway which is 192.168.1.1. I also tried switching to another cable just in case but to no avail.
Here are some info:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersMiko Luis>ipconfig/all
[Code].....
I have just made a new home network with a Trendnet TEW-652BRP N router.I am trying to set up my encryption but I am confused on it. Under Security "Authencation Type" there is WEP, WPA, WPA-2, WPA-AUTO. What are these settings for and which do I choose for a home wireless net work?
View 3 Replies View RelatedI have a d-link DI-524, Im using a modem Xyzel P600 series, my ethernet card is Realtek RTL8101E Family PCI-E.
I already set-up my router and modem. Most of my wireless devices can connect. My problem is it is not secured. When I tried to add WEP or WPA, D-Link restarts but then it cannot connect to my DSL. it says DHCP disconnected and when i try to renew, nothing happened. It just kept on reconnecting. My Desktop has no internet connection.
I connect to my d-link via 192.168.0.1
ok I have logged in my router & clicked the repeater mode. whats the next step. BTW I am a complete newby to networking.
View 4 Replies View RelatedI have a similar problem to thread with same name dated 31-Jul-2010-that is now closed. I'm using Qwest internet with Actiontec PK5000, and I have to use my Netgear WNR2000v3 as a repeater.The Netgear is working as a repeater however I can't get internet through the LAN connections on the repeater. After checking the settings over and over again I'm beginning to think the repeater will only work with wifi. I need to hook up my desktop in the office, DirectTV, and Blueray player LAN connections to my repeater.
View 1 Replies View Related