Use Windows To Configure Wireless Network?
Jan 6, 2012
I can not find the option "Use windows to configure wireless network."
This is what I have done so far:
Control Panel> Network and Internet Connection> Network Connections> Right-click Wireless Network Connection> Properties and a window with two headings opens: General and Advance. There is no "Use windows to configure wireless network" option.
View 3 Replies
ADVERTISEMENT
Sep 10, 2012
I have two Windows7 machines (PC and laptop). I've set PC as VPN server and laptop as VPN client using default built-in W7 network tools. I've disabled use default gateway in remote network on client machine, so client don't try to route all communication through VPN. I've routed port 1723 (TCP/UDP) on NAT to my server and enabled IPSec/PPTP/L2TP passthrough
I've put my laptop in indepedent network (basically I've connected it via 3G network), connected to VPN server and checked ipconfig /all
I've get:
IP Address: 192.168.1.101
Mask: 255.255.255.255
Gateway: (none)
LAN mask in server LAN network is 255.255.255.0 - I am surely missing something obvious, but Google doesn't give me any good advices; How can I access local LAN network from remote VPN client? How can I access local shared documents?
View 2 Replies
View Related
Mar 29, 2011
How to configure in windows server 2008 network NIC1 is WAN and NIC2 is LAN?
View 1 Replies
View Related
Jan 20, 2012
Just picked up a WEC600N Wireless N Express Card and installed. It's working, but it's connected at 54mb and I cannot find out how to configure the wireless settings. I think I am using the Intel Proset wireless software.
Also, router is a netgear wndr3700.
View 1 Replies
View Related
Aug 20, 2011
I am using the wireless router WRT54G2 V1 to configure on windows 7 . How to configure that .... It is working on windows XP
View 1 Replies
View Related
Oct 3, 2006
My lap top and pc were both accessing internet fine. Now my laptop has the message windows cannot config. wireless connection. If you have enabled another prog. to manage this connection use that software. Then it says ifI want windows to config., start WZC service. I am a novice and don't understand any of this. I don't think I have done anything to enable another prog to manage the connection. I have tried reloading isp disc and making new network connection but to no avail. the little network logo has a red x constantly.
View 4 Replies
View Related
Sep 8, 2012
My laptop has windows xp.my home has wireless network.how can i configure to my labtop with wireless network?
View 4 Replies
View Related
Aug 25, 2011
I want to know how to configure a wireless network using an wireless router???
View 1 Replies
View Related
Aug 21, 2012
This past weekend I went out of town and took my Windows 7 laptop with me -- since I returned home, it has been unable to connect to my wireless network. Other devices in my home connect to the network just fine, and the problem laptop has always been fine until now. My network card is an Atheros AR9285, and I'm attempting to connect to a Medialink router with WPA password protection and AES encryption.My wireless network icon in the task bar has a yellow sign with an exclamation point in it. It says "No Internet access."
View 1 Replies
View Related
Aug 30, 2012
I'm using windows XP Pro , in a local Lan, internet connection through a DHCP, and System software on IP 192.168.0.254. I'm the Admin of my PC, I just want to use the Internet and the System program. I want to block any user from accessing my PC or viewing my Processes by other programs like (Ideal Admin.). How to configure the AVG Firewall to do that ??
View 11 Replies
View Related
Dec 6, 2011
How to configure win 7 to a xp ethernet lan
View 1 Replies
View Related
Mar 22, 2011
Networking and troubleshooting windows problem.
View 2 Replies
View Related
May 25, 2012
I am trying to configure wireless network to my computer but it keeps asking for security key which I am not privy to.
View 1 Replies
View Related
Feb 3, 2013
We want to configure a Cisco WAP 321 to NPS on windows 2008.
On NPS system event viewer :
An Access-Request message was recived from RADIUS client XXXXXX with a Message-Authenticatior attribute that is not valid.
We have installed other RADIUS client on Windows 2003 Server and we have the same error.
On the Web interface of Cisco WAP only can configure the IP and password of the Radius server.
View 1 Replies
View Related
Aug 21, 2011
Network set up; wireless router (D-link DIR825) to Cisco switch (SD208p) and have Wap200 hooked to cisco switch to extend range up one floor. Can see it as wireless network, but cannot configure it with web browser. Address 192.168.1.245 just times out via pings as well. Have done all resets, power on reset, etc nothing.
View 3 Replies
View Related
Jun 11, 2012
configure PEAP for wireless with Windows 2008. The doc we have only mentions Windows 2003. When we follw that document we get a faulure when we try to bind the certificate to we have generated to ACS 5.0 .
View 1 Replies
View Related
Apr 16, 2013
I want to set up a domain for a file server and MS SQL 2005 server on my server machine and installed windows server 2008 in it.
Do I need to set up DHCP server and DNS on Windows server 2008R2 or leave them to the router to do the job?
View 1 Replies
View Related
Apr 2, 2013
I have Dlink DWL - 2000AP+.
What I want to do is, to reproduce WiFi signal (from TP-LINK modem) by repeating with D-Link Wireless Access Point.
Here is how web interface looks. There is an option for repeating:
After clicking Site Survey I see all list of available networks. When I select one of them, the D-link saves changes then reboots. After that, Windows shows me something like that on available WiFi networks list:
<Repeated network name> 2
The problem is, when I connect to this network, Windows connects directly into root source, not to my WAP (I see this with inSSIDer utility).
View 1 Replies
View Related
Apr 7, 2013
Is there any way to configure a wired guest network with a combination of 5508 and 2504 wireless controllers? I am aware that the 2504 does not have wired guest functionality, however is it possible to set up a wired guest on the 5508 and using mobility anchors, transmit the l2 information through eoip to communicate with the remote vlan?Home built NAC solution, using 802.1x authentication on switchports for public areas. If user is an employee, communicates with the supplicant on their machine, and places them on an internal vlan.If user is a guest, user fails 802.1x check and is placed on a "guest" vlan with an ACL and external DNS.If placed on the guest vlan, the user has to accept a terms of use form.This is working currently with our 5508s without any issue, however we have some remote offices we'd like to roll this out to that are using 2504 controllers. I'm hoping there's a way that I can use the 5508 as an anchor or vice versa to make this work.
View 1 Replies
View Related
Feb 6, 2012
How do I configure a local area net work with unbounded media?
View 1 Replies
View Related
Jan 29, 2011
I'd like to give my DIR-655 (rev. A4, firmware 1.32) to my brother for use as a repeater, to work with the weak signal in his apartment. But I don't see any way to configure the device to join an existing wireless network. Am I wasting my time?
View 7 Replies
View Related
Jul 8, 2011
I've downloaded the driver for a tenda usb adapter. What else do I need to do to connect to the WRT54G network? I'm currently connected via an ethernet cable. Running Windows/7.
View 1 Replies
View Related
Apr 25, 2011
In my collage i have a LAN to the wind server 2003 again i m also configure a small LAN may be take a 5 computer but the communication is not done.
View 1 Replies
View Related
Jun 27, 2012
I have a Cisco 4200 Wireless Router connected directly to my cable modem. To extend the wireless range I purchased a Cisco 2500 Wireless Router. As the house is "wired," I can connect the Cisco 2500 to the cable modem in a room separate from the Cisco 4200. My question is how do I configure the Cisco 2500 to connect to the network and provide wireless coverage from both routers.
View 6 Replies
View Related
Feb 1, 2013
The situation is Main house running Linksys EA4200, I have a garage apartment rental that is to far away to receive the wireless guest network.I ran a cat5e to the apartment, can I configure the EA4200 to allow the WAP54G access point to use the guest network? I want to prevent my renters from having access to the home network, but just have basic internet access separate/outside my network.
View 6 Replies
View Related
Aug 4, 2012
I have had several Linksys and Cisco routers in the past, and I'm a network engineer. My E3000 died after only 18 months so I had to run down and buy a new router, thus the EA4500.
I use the manual way to configure all my network gear. Nothing on my network changed, except the router replacement.If I leave the router default address at the 192 range, DHCP will issue a IP address. However, I do not use that range and after cdhanging the range, setting my start IP address, etc, I save everything and even tried rebooting the router to no avail. The router will not issue a DHCP addrss if you change the default range.
I can manually configure my clients with a static IP and all is good, no issues at all. I just can't get DHCP to work. My E3000 was configured exactly the same way and worked just fine, well up until two days ago.I have tried upgrading to the latest router firmware, so I'm not on 2.0.37 and I did set the router back to Factory Defaults, rebooted, then configured it, and still no DCHP.
View 7 Replies
View Related
Feb 6, 2012
I have windows vista, and forgot my network password. I reset my router to factory settings by pushing the reset button on the back.I tried reconfiguring the router from the network icon, but at the end of the process it says it cannot configure my router.I lost my internet service in the process
View 1 Replies
View Related
Feb 7, 2011
Is it possible to configure split tunneling for default Windows VPN Client and ASA 8.0? Everything works fine with Cisco VPN Client
View 3 Replies
View Related
Feb 4, 2013
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I have an unused TD-W8151N. I also have a smart TV that requires a wired connection, with no way of getting a wire to it.
Can I configure my spare TD-W8151N as a client of the existing WiFi network and connect the TV in to the TD-W8151N with a cable?
View 2 Replies
View Related
Jan 6, 2013
I got error message everytime i try to configure home network defender and i tried to find the solution but no luck but everytime i click and enter my email and password i get this message, i bough this router recently and the only troubles i have is with this
View 2 Replies
View Related
Apr 5, 2011
I'm trying to configure my BRI interface in "network protocol-emulate network" and "layer1-emulate network" but i don't have this second command.Is someone have allready to that with this type of interface ?I've to configure this because the ISDN line of my telco is in user mode only.
View 5 Replies
View Related
Aug 6, 2011
Is it possible to configure the apple airport express to extend a linksys wrt120N wireless network? if so how?
View 2 Replies
View Related
Jan 14, 2013
I need to configure two VLANs in my home network to separate a server 1 with VM from another part of network with server 2 and wifi clients. Is it possible to keep DHCP server and internet access on E2500 enabled for both vlans? If so, how should I configure ports tagging (variant shown on screen shoot below doesn't work).
View 5 Replies
View Related