Wireless :: Speedstream Se568 Cannot Connect To HisenseTV?
Jul 4, 2011
I am trying to add my Hisense LED42T18GP to my home Siemans Gigaset SE568 WAN. The TV has two modes of setting up access to the Network Neighbourhood DHCP IP (AUTO) and Fix IP (Manual) I can't get either to connect and I suspect I have to change something on the Router.When I select auto setup I get "On: DHCP not ready!" when I set the fixed IP I get "On: Can't get any IP" The TV handbook is no goog, there are 3 things to be set 1) IP address but it does not say IP address of what - Router, Desktop computer or TV. 2) Network mask is no problem. 3) default gateway does not specipy if this should be the IP address of the Router, WAN or desktop computer. I have tried every combination of each and always get the same result. The router has Full internet Gateway Device IGD support enabled.
I'm trying to hook up a Siemens Speedstream 4100 and a Linksys E2500. The internet works fine when I plug the modem directly into the computer. When I try to run it through the router, though, the router install appears to work right but I get a message saying that my internet connection might not be working. I power-cycled everything - unplugged all the cords and waited 20 minutes before restarting. It sounds like putting my modem in bridge mode might be the move? When I type in 192.168.0.1, I get a message that says "Server says: Linksys E2500." It also wants login information, and I'm not sure what that would be.
I already connected the wires to my computer and I already switch on the power of the GIGASET , unfortunately I still cannot connect to the internet using my PSP and LAPTOP
A Seimens Gigaset SE568 Wireless Router connected to a DSL Line and broadcasting a WIFI signal throughout my house. I receive this WIFI internet connection on my laptops using their respective WIFI adapters, and on my desktop using a GASKY GS-28USB Wireless USB Adapter, and use this internet connection simultaneously in both desktops and laptops.Now, I am shifing to a new 3G USB Mobile Broadband service:
Where I can directly connect the 3G USB Mobile Broadband Stick to my desktop or my laptop and use the internet directly, but not all at once through my router as was previously configured.Is there a way using the existing hardware, can I configure my desktop to share this internet connection and broadcast from the GASKY GS-28USB Wireless Lan Card to the Seimens Gigaset SE568 router and then throughout my house for simultaneous access, or directly share the internet through the GASKY adapter itself, or is there some other configuration I can use ?My Desktop has Windows 7 installed as an operating system.
My brother's Speedstream has died. Lights don't work, etc. etc. He has ATT DSL in Detroit; Detroit does not have an internet wireless service, so he has to deal with ATT. He's po'd that he's paying $92 a month for service that doesn't work. I told him he needed a new DSL modem.
I fiddled with the configure screens using the admin/admin id/password and using the settings from the modem I was given from YAK I now have the SpeedStream 6250 working! If you enter in all the addresses into the various locations the modem will work. Even though it's the Bell interface"
I had windstreams modem "speedstream 4200" but parents for whatever reason thought the 4300 would change everything. With the 4200 I was open for gaming, could connect. With this 4300 I can't connect to anyone at all. I disabled DHCP server in my rotuer and that aving more fails than succeeds. (in connecting to people).My router doesn't have bridge mode but my modem does, I don't know what it does in the modem. My friend had the exact same problem I did and he put his router in bridge mode which I do not.
How I connect internet through wi-fi using BSNL Broadband I want to know primary DNS step 1/2, My Mobile set is Nokia C3-01 and Router is Seimen gigaset SE568. My Mobile Nokia C3-01 is not connecting internet through wi-fi using BSNL Broadband. I need to fill the primary DNS step 1/2 in the settings so I want to know the primary DNS
I have a wireless Linksys E1500 router, and for quite a few months now, my router just stopped working properly. It quit, I unplugged everything and plugged it back in, and it worked, but from that point on, it's been displaying this:
I just bought the e1000 router today and I'm already having trouble. I got it setup the first time and all my computers set up with it and it works fine for internet. Everything is snappy and responsive and I don't have any of the problems I did with my old belkin. However, I am unable to connect to the router using cisco connect or the web interface. I need to forward ports, configure wireless security, etc etc. All I did was disable the guest account through cisco connect, and then when the software just sat there doing nothing with the spinning circle in the middle, I opened task manager and killed the process to get it to go away. Now I can't connect using either cisco connect or the web interface.
Recently I installed connectify because my uni flat only had one wired outlet, and I wanted to use my xbox at the same time. It worked perfectly, but when I returned home I found my laptop could no longer connect to the home network, it just says it cannot connect, but all the over devices in the house work. My laptop can still connect to the internet via an ethernet cable but this isnt practical at home. I've uninstalled the connectify program, and tried my best to make sure I got rid of all the stuff it's done, but still my problem persists
Any way to connect a wifi usb to a wireless router for better wifi connect?? i have wifi but it only gets in the room of the house im in and want it to work though out the house not just one room
I have just built a PC desktop and do not think it has the wireless built-in on the motherboard. I'd like to connect to the local network wirelessly. I know that the easiest answer to this is to get a wireless PCI card. But can I ask that in order to be able to access to the LAN wirelessly, I could plug my PC directly into the wireless access point TP-Link.
I have just moved in to a basement apartment and can connect to the internet with my wireless but not with the ethernet cord ran downstairs for me. The other computers upstairs work fine on ethernet through the same router. I do not understand what the problem could be. here are my configs:
Microsoft Windows [Version 6.0.6002] Copyright (c) 2006 Microsoft Corporation. All rights reserved. Windows IP Configuration
I can't seem to connect my laptop using my ethernet cable, but I'm able to connect it to the Internet using my wireless connection. Whenever I plug in the cable, my computer tells me that the LAN connection is connected, but I can't open a web page. I tried connecting the cable onto another laptop and it worked, so I don't know what's up with the LAN connection on mine.
Command Prompt Message after ipconfig /all:
Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : NVIDIA nForce Networking Controller
I have a new broadband connection and I was kinda facing problems connecting wirelessly with my router.So I did go to my router page and then cloned my MAC book's mac id, and it worked fine. I'm able to connect to the internet wirelessly. However, I can't connect to internet from an Windows XP lappy. I have removed, re-added the network, the network is very much identified but the laptop doesn't wanna connect to the internet wirelessly.Both the laptops MAC Book pro and Dell(the one which has XP loaded) were able to connect without any problem in the previous ISP's case but XP doesn't wanna connect to with the new ISP.
WRT610v2 running latest firmware. xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.
Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars. Connects to 2.4 network just fine, Won't pull an ip address and reports "Not connected" when I select the 5.0 network.
I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network. So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not. If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
Android users can connect to our hospital guest wireless but will not have connectivity. Our wireless infrastructure is WISM based with 2 controllers on 6509 platform. We have a mixed environment of 1231, 1252 & 3502 series APs.
Had issue connecting just Android devices? All other devices connect fine.
I have a WUSB11 Wireless B and wonder if it accepts WPA2 security, I originally had my router set to WPA, and the wireless B worked fine, I have since changed to WPA2 and notice the Wireless B device won't connect.
I have wonder that my laptop has wireless, and when i connect it to router to use internet it show wireless now is connect, but when i open the website it show not work..and this problem occur only my computer. and when the other computer laptop they can connect and use internet normal...
I have just installed the E1200 router to my cable internet and it works great, but my printer is not wireless and is not even being recognized as an device on my computer. How do I now connect my printer?
I have a E4200v2 and im getting wireless connection issues. I have updated to the lastest firmware and have checked all my wireless settings. I dont use usb storeage. I have 1 laptop using 5G, my iphone using 2G and my wife mac using also 2G.. the problem is that, once we stop using the 2G connection (leave it overnight), it just dies the next day.. it wont connect, i double check the password and it wont connect. But the 5G connection is fine.. Do i have a break E4200v2? or anyway of fixing this?
I have a nintendo dsi and a 7" wireless netbook and 7" notebook. It says signal strength good, it even says connected. But when I goto internet unable to connect. We have a wireless laptop that works fine.
My laptop can't connect to the wireless internet at my workplace, but I can connect to the wireless internet at my house.I'm very sure that the wireless internet at my workplace works because all of my co-workers can connect their iPad, smartphones, laptops...etc to the internet.I just can't get my laptop connected. I entered the right password, and then the connecting status keeps changing back and forth between "Connected" and "Limited access". It also shows "Identifying... no network access" all the time.I really don't know what happened to my laptop's setting. I have tried to remove the wireless network from "Managing Wireless Network" and set it back up again, but it doesn't work at all.
