I have just built a PC desktop and do not think it has the wireless built-in on the motherboard. I'd like to connect to the local network wirelessly. I know that the easiest answer to this is to get a wireless PCI card. But can I ask that in order to be able to access to the LAN wirelessly, I could plug my PC directly into the wireless access point TP-Link.
View 1 RepliesI have a wireless att dsl modum with uverse and wireless laptop connectivity. the wireless somehow stopped, but i can connect directly and reach the internet. I have ping tested the nic card and it seems fine. I have rebooted the modum, the computer to no avail??
View 1 Replies View Relatedsomehow connecting my PC to my home network as if it was wired. Having a wired connection just won't work because my PC is far away from my modem and router. The reason I want to connect it wired is because I am getting terrible speeds, and the slowest. [URL]
View 1 Replies View RelatedMy question is how can I use this existing wi-fi as input to a router to make a sub wi-fi for four computers and a wireless printer. Some of my computers may need to be wired into the router.
View 5 Replies View RelatedI've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
I have a Netgear WNDR3700v2 that I was very happy with until I got a nest thermostat. Apparently it is an unsupported router and I had to change it. I bought a E2700 since it was supported, but I'm having a huge dilemma...
If I connect the linksys directly to the modem, I'm not getting an internet connection. I've released and renewed IPs to no avail..
but if I hardwire the linksys to the netgear, I do get a good solid internet connection. problem is, I have no need for 2 routers setup on top of each other.
basically, I dont understand why linksys is not able to connect directly to the modem. yet it gets solid connection hardwired through another router.
I'm using Comcast and in south FL. it's a motorola surfboard modem
I recently purchased the router and got the CCC firmware on. It works fine for a while but then I can't connect to the router using my PC unless I log using the remote credentials. Generally if this were the case I wouldn't care but when I do it that way I can't run the speed test. After I reboot the router it works fine again, for a while.
For some reason, it doesn't detect my PC as being connected directly although my PC is connected by wire, directly to the router.
I have external hard drive connected to E3000. It is formatted as NTFS and working fine. However if I disconnect from router and connect to PC usb port directly, I get a message that hard drive needs to be formatted.
View 2 Replies View RelatedI have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
View 9 Replies View RelatedI have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
View 5 Replies View RelatedMy desktop gateway computer slowly started having problems connecting to the internet via the hard ethernet connection to the router(Netgear). Wireless devices connected OK (although often slow). I assumed it was the router so I bought a new one (Linksys), but it's having the same problem. New router I can connect to with my laptop but not with the desktop. Latest errors during setup are Local Area Connection does not have a valid IP configuration and the default gate way is not available.
I restore to factory defaults? I'm running Windows 7 Home Premium on the desktop.
from the main line (internet port), i distribute to 1st 4 ports router (Bluelink R33N) which is 2 connected to the computer + 1 connect to another router (Dlink).. but the 2nd router (DLink) is not working with the internet line.. Tried to connect direct from main server to Dlink, and it's working well, but when use 2 routers in single line, just didnt work.
View 5 Replies View RelatedI wanted to connect to the internet so plugged the same cable into my laptop (running 7) [code]...
View 3 Replies View RelatedI have a Broadband Optical fibre cable which i used to connect directly to my Desktop and Laptop, i am running win7 on on my desktop/laptop, yesterday I installed Belkin router for my Laptop, worked fine, laptop is wireless now. But when I connected the desktop directly there is an error "670 cannot connect to the server/ cannot find the modem" I deleted the dialup and created new one still the same issue. However If i connect the cable through the Router to the desktop it works. I think I lost the direct connection.
View 2 Replies View RelatedWe have a DIR 655 router that I have set up with LAN and WiFi, all good.Today we received our mast and antenna from Vodacom (ISP) with the Public IP's to enter into the router. We connected the LAN cable into the Internet Port and did a manual Internet Static IP setup. But as soon as we click save it says: Type is not for 3G... How do I go about entering the public (static) IP's we received from the ISP in order to get the Internet operational?
View 8 Replies View RelatedSo I recently just built a new pc for gaming, I can't seem to connect to the internet through my router or directly through my modem. I have connected directly on my laptop and it works and through router and it works.
View 1 Replies View RelatedCan i connect my 3g USB modem to my dlink router directly through the usb port.
View 10 Replies View RelatedI cannot connect to the internet via my router. The router is functioning properly two other computers in the house use the router one though Ethernet cable and the other one connects wireless. Things I have done while trying to figure out the problemMade sure all windows updates were up to date Scanned for viruses and malware (none were found) Uninstall the network adapter Made sure the network adapter driver were up to date
I have noticed that when I plug the Ethernet cable from the router to the computer the led on the back of the computer panel does not blink as it does when I route directly from he cable modem.
I want to connect a Netgear FS605 directly to my ADSL router.However I find that this does not work unless I put my Netgear EN2005 Hub in between the Switch and the Router.The Hub is 10Mb/sec the switch 100Mb/s so I would like to eliminate the hub.
View 3 Replies View RelatedI have need to test async communications through a pair of CGR 2010's..This emulates some particular serial-talking-only devices at either end that want to communicate with eachother. I've done stuff like this before but with modems attached to the PC's.
View 1 Replies View RelatedCan not connect computer to Cisco Connect -.Receive error msg 82BD0305. Reset to EA3500 to default and reinstalled software.
View 8 Replies View RelatedI have a wireless Linksys E1500 router, and for quite a few months now, my router just stopped working properly. It quit, I unplugged everything and plugged it back in, and it worked, but from that point on, it's been displaying this:
I've tried changing the Ethernet cables
I just bought the e1000 router today and I'm already having trouble. I got it setup the first time and all my computers set up with it and it works fine for internet. Everything is snappy and responsive and I don't have any of the problems I did with my old belkin. However, I am unable to connect to the router using cisco connect or the web interface. I need to forward ports, configure wireless security, etc etc. All I did was disable the guest account through cisco connect, and then when the software just sat there doing nothing with the spinning circle in the middle, I opened task manager and killed the process to get it to go away. Now I can't connect using either cisco connect or the web interface.
View 7 Replies View RelatedRecently I installed connectify because my uni flat only had one wired outlet, and I wanted to use my xbox at the same time. It worked perfectly, but when I returned home I found my laptop could no longer connect to the home network, it just says it cannot connect, but all the over devices in the house work. My laptop can still connect to the internet via an ethernet cable but this isnt practical at home. I've uninstalled the connectify program, and tried my best to make sure I got rid of all the stuff it's done, but still my problem persists
View 5 Replies View RelatedAny way to connect a wifi usb to a wireless router for better wifi connect?? i have wifi but it only gets in the room of the house im in and want it to work though out the house not just one room
View 1 Replies View RelatedI have just moved in to a basement apartment and can connect to the internet with my wireless but not with the ethernet cord ran downstairs for me. The other computers upstairs work fine on ethernet through the same router. I do not understand what the problem could be. here are my configs:
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
Windows IP Configuration
[Code].....
I can't seem to connect my laptop using my ethernet cable, but I'm able to connect it to the Internet using my wireless connection. Whenever I plug in the cable, my computer tells me that the LAN connection is connected, but I can't open a web page. I tried connecting the cable onto another laptop and it worked, so I don't know what's up with the LAN connection on mine.
Command Prompt Message after ipconfig /all:
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : NVIDIA nForce Networking Controller
[code].....
I got my final assignment from school, and my teacher asked me to configure 2 Access Points (1200 series) directly on a Wireless Controler (Cisco 2106). I can't ask my teacher for any questions, cause he doesn't know how to configure it also, THAT's why he's asking me to do it.I've learned a lot of things about the default static interfaces (the "management" and "ap_manager" interface), but i can't seem to fully understand how to configure it.I want to use the Internal DHCP server of the WLC. How I can get those 2 Access Points working on the WLC. I only seem to get DHCP issues.
This is what i've done:
- Leave the configuration of the "management" and the "ap_manager" default (172.16.1.30 and 172.16.1.30). Bound to port 1
- Made a new interface "AP1" with IP-Address 10.0.0.10 (/24), default gateway 10.0.0.1. Primary DHCP server: 172.167.1.30
- Made a new interface "AP2" with IP-Address 192.168.1.10 (/24), default gateway 192.168.1.1. Primary DHCP server: 172.167.1.30
- Made 2 DHCP scopes within the 192.168.1.0 and 10.0.0.0 networks.
For some reason, when i boot up both AP's, the won't get any DHCP address.
I want to buy a wireless router to which I can connect my USB internet device directly, so I don't have to turn on my PC all the time if I just want to use my moble phone or iPOD or other family members wanting to connect to internet.
View 1 Replies View Relatedi'm using WLC AIRCT5508-K9 software version 7.3.101.0, ISE, cisco prime infrastructure 1.2 (1.2.1.012), and using Odyssey access client manager all running well but here the problem, when a user connected to our SSID, the status of connection information especially on access point.. there appear that "Access point : WLC2-ISC-JKT-GCC".that is the WLC not the access point, is there any miss configuration from me..
View 5 Replies View RelatedCan I use WLC 5508 with OpenLDAP directly (without radius) ?
View 1 Replies View RelatedDoes Cisco have an official number of how many AP541s are supported directly by a UC560? these are standalones and I know they are configured in a max of 10 to a cluster, but how many clusters can you have? We are looking at a hospital installation with one UC560 and 25 AP541s.
View 2 Replies View RelatedI am in the process of opening an internet cafe. I dont know exactly what a pc server does on the network... or do I really need one? Is the switch/hub sufficent to connect all pcs to the moderm to connect to the internet?
View 1 Replies View Related