Have the following set up: cable modem>wifirouter>gigabit ethernet switch>to 16 ports throughout house. When I connect a second wifi router to any port around the house, the internet does not work with connecting to that specific router, however, if I use a lan cable and connect direct with my mac or cpu, internet works fine. wifi routers are not communicating with lag ports
View 3 RepliesI have a D-link WBR-2310 wireless router connected to a ZyXEL P-600 series modem. Everything worked fine untill a couple days ago when I had a power surge; since then the wireless router won't show on the modem that the ethernet cable is plugged in, and I get no wireless or DSL internet. I called the internet service provider, and they told me to reset both the modem and the router, which I did and it worked fine for about an hour; then it didn't recognize the cable again. I thought maybe it was the ethernet cable itself so I bought a new one, and it didn't correct the problem. When I hook any of the cables up directly from the modem to the labtop or the pc the ethernet light comes on and I have internet connection again. Why doesn't my router recognize the cable?
View 1 Replies View RelatedI have a compaw CQ61 that is using the operating system windows 7 64x.
The problem occurred today when logging onto windows. Windows tells me that the connection i have to the router is limited. Other devices i have in the house are capable of connecting to the wifi router. When deleting the connection and trying to reconnect to the router, it brings up the message that it is taking longer than expected to establish a connection and then eventually brings up the message "limited connetion"
When trying to connect the laptop to the router via cable, it doesn't even recognise that it is connected and does not establish a connection.
When using the windows connection troubleshoot, it detects a driver problem with both the wifi adapter and the Lan adapater. Therefore i uninstalled and reinstalled both devices but still suffered the same problem.
When clicking the connection i am attempting to connect to, right click status, details.. everything is in blank, it gives no information regarding to the connection.
I have a Dell XPS M1530 with Vista 32 bit. When i plug in a cable i get nothing, no error, and the comp does not recognize that a cable has been plugged in. I think that this started after my Hard drive failed and Dell replaced it but i'm not positive. No errors (? or !) in Device Manager and I can't find the Marvell 88E80XX 10/100 Ethernet Controller in device manager. I have attempted to Reinstall the drivers. The wireless is still working. I have one Light to the right of the port that is on all the time solid but no flashing with the cable in or out.
View 14 Replies View Relatedmy laptop stopped recognizing my wireless router out of nowhere. One minute it was connected to the internet, the next it was on and off, I reset it and restarted and it wasn't recognized. Currently only working if Ihave an ethernet cable directly connected from modem to laptop or modem to router/router to laptop.
Specs:
Windows 7
Time Warner Cable modem
Edimax wireless router
I HAVE TWO COMPUTERS running Windows Xp that are CONNECTED TO A ROUTER THEN CONNECTED TO A MODEM, COM1 THE INTERNET WORKS FINE, AND IS SHOWING A LAN CONNECTION WORKING, AND INTERNET GATEWAY CONNECTED, AND THE ROUTER SHOWS UP ON THE MY NETWORK PLACES. ALSO MY WIFI WORKS FINE TOO! BUT COM2 CANT SURF THE WEB, IT DOES NOT RECOGNIZE THE ROUTER IN MY NETWORK PLACES, AND THE INTERNET GATEWAY IS NOT SHOWING UP IN NETWORK CONNECTIONS, BUT THE LAN IS, AND IS SHOWING A CONNECTION. i have tried restarting everything, i tried connecting the COM2 straight to the modem, tried new either cables, nothing wrong with my service or modem or router, its just the COM2
View 7 Replies View RelatedSo this morning I was planning to reset my router because my internet was feeling a bit laggy. Omce i did, its lights turned on except for the ethernet light.It was working perfectly last night
Ive tried resetting the router a few times with no results
ive ran the Windows troubleshooter with it recognizing that:
The Local Area Connection adapter is disabled: Detected
Enable the wired network adapter: Not run
My main networking device is the Ericsson T073G HGU ONT, and when I am connecting to the network through the Ethernet there are no problems. However when I connect my Belkin F6D4230-4 router to it (through cable) my router cannot recognize the modem.
View 18 Replies View RelatedMy linksys router all of a sudden stopped recognizing the 3 LAN lines that are hooked up to it, we are only able to access the internet via wireless. any suggestions on why the router would all of a sudden stop recognizing the LAN lines?
View 7 Replies View RelatedI have a Linksys WRT54GS router that is giving my some trouble. I recently got a new PC and moved my old one into my bedroom along with my Xbox 360. So I didn't have to switch my Ethernet cable between my xbox and pc I bought another cable. Much to my dismay this new cable would not work. At first I thought maybe the cable was bad, but when I connect my pc directly into my modem it works fine. This had my come to the conclusion that it was my router. I have two pcs hooked into it that work fine and a laptop that connects to it wirelessly, but if I try to hook my xbox or pc to it using the new cable they just act as if there isn't a cable connected. When I look at my router the light for the ethernet port that the new cable is in will flash on and off. I've hard reset my router and updated the firmware.
View 2 Replies View RelatedI have a setup where there are two networks. A 172.16.0.0/16 and a 10.1.0.0/16 that are separated by the dlink router. I am able to ping from the 172 network to the 10 network using a laptop that is directly connected to the router and that laptop can also browse the web fine. However, I cannot ping to that router or access that subnet at all from the 10 network (if I try to access its LAN (the 172 network)). The 172 network is on its LAN and the 10 network is its WAN. I can access its WAN fine. Also, there the router is not recognizing the laptop as a "directly connected deivce" but its not preventing the laptop from using the router. I have tried to make the router as least secure as possible but still nothing.
I thought about making Static Route to point towards the router's LAN but the only option it gives me is the WAN for the exit interface.
I recently upgraded to the EA4500 and the only issue I'm having is that it will not recognize my static DNS settings, which worked fine on my older E2000. No other hardware has changed except the router.I've tried both Google DNS and OpenDNS. In either case, the DNS settings can be entered and saved in the Basic Settings tab, but when I go to the admin tab, it shows my ISP's deafult DNS.
View 4 Replies View RelatedI attached WD My Book Mirror 2TB to E4200 with firmware 1.0.01 but it was very UNreliable. It would give I/O errors when I tried to access the harddisk. So I upgraded to firmware 1.0.02. Now E4200 doesn't recognize my hard disk at all. Yes, my hard disk is in the list of tested devices using NTFS.I contacted support but no luck.
I also have bad range with this router where I am only about 20ft from the router (2 walls in between) but I get about 3 bars out of 5 on my Windows 7. Could it be because I purchased a refurbished product directly from Cisco?
My laptop is refusing to recognize the router. Until yesterday everything was fine, now it's not recognizing it at all. There are other computers on the network that connect just fine. When i go to Device Manager it is also missing the following:
Base System Device
Base System Device
Base System Device
Ethernet Controller
Network Controller
PCI Device
SM Bus Controller
Video Controller
Video Controller (VGA Compatible)
Since I can't get onto the internet from that computer, where to go to get the drivers for these to download.
My main networking device is the Ericsson T073G HGU ONT, and when I am connecting to the network through the Ethernet there are no problems. However when I connect my Belkin F6D4230-4 router to it (through cable) my router cannot recognize the modem.I have tried literally everything.
View 7 Replies View RelatedMy Motorola 850G router is several years old and working fine. However, my wi-fi connection is presently "unsecured" and I need some assistance as to how to go about setting up a secure network. My browser is not recognizing the router's default IP address.
View 1 Replies View RelatedBought GoFlex Home 3TB, plugged into Cisco WRT310N V2, w/ Desktop PC (Win 7 64bit) does not recognize the drive. Get NETWORK ERROR "Windows cannot access \goflex_home" Error Code: 0x80070035. Can not map netork drive. Under Win Explorer the drive DOES appear as "GoFlex Home:UPNP-AV" in TWO places, 1) under Media Devices & 2) Under Storage. Bother places are treated as MEDIA because, when I click on either of them it opens Windows Media Player! I can type in the IP address in BOTH IE & WIn Explorer and it will take me to the web page for the drive, where i can log in and create users, add folderes, etc. I WANT TO USE THIS AS A BACK-UP DRIVE, but can't get WINDOWS TO RECOGNIZE IT. I have turned off McAfee
View 3 Replies View RelatedI have a E4200 router, and I had previously plugged in a small external hard drive just to test the functionality. The router seemed to recognize the storage, and the computers on the network could see it as a shared drive. Now I have plugged in a Seagate 7200 internal hard drive inside a Rocketfish enclosure, but the router is not recognizing anything. I just upgraded the firmware to 1.0.04, but there was no change. Are there problems using an enclosure rather than just plugging in an external hard drive?
View 1 Replies View RelatedI bought an EA6500 router mid january. Firmware is 1.1.28.146856 from day 1 I used this new router. I attached my 750Gb Maxtor OneTouch 4 USB disk to it to share data over my network. I was able to define shares on it. Perfect. .. until I wanted to copy several GB's to this disk. It indicated it would take more than 1 day to finish this copy. So I removed this disc from the router (after removing it in the USB menu). I copied the data from my pc to the disc and attached it back to the router. From then on, it always indicates that no disc is present. Resetting the router did not work. Attaching a USB stick to the router does not cause a problem. It is visible and I can copy data to it. After attaching my Maxtor again, it shows no stations attached... (sharing a disk via the router was one of the reasons for buying this type)
View 2 Replies View RelatedHow to install single port D-link wifi router through Modem "Single Port Wifi Router"
View 1 Replies View RelatedI would like to connect my USB WIFI dongle directly to my wired router, this would enable me to have wifi access without having my PC switched on all the time, is this possible and if so what kind of adapter do I need? I think I need USB A Female to Ethernet RJ45 Male Router Adapter.
View 5 Replies View RelatedI am trying to scan a directv device that is connected on my lan it uses port 8080. My hardwired machine returns the expected data, any call from a device connected via my wireless network returns a page can not be displayed. It appears as if the router is blocking ports 8080 over wifi only.
View 4 Replies View RelatedI've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
View 1 Replies View RelatedI'm looking to replace a broken Linksys 8-port router that was connected to a D-Link Wi-Fi unit. I'm not sure what hardware to go with for use in a house ~2000 sq. ft. I'll be using an Xbox (currently hardwired), Wii (wifi equipped), iPad, PC laptop along with a desk top PC (currently hardwired) sometimes simultaneously.
View 2 Replies View RelatedI have just upgraded my Linksys router from an older one to the E-2500 about a week ago. Everything is working great on my wired desktop and 3 wireless laptops except the printer will no longer work from any of the computers. I've checked the printer wireless settings and they are correct (ssid and password) and it says it's connected to the wlan. Each of the computers shows the printer is active and set to default BUT the port light on the back of the new router is not on. I have changed cables and still no light, the printer is set up for sharing and it did work a couple days ago but port light was on then.
I have not added anything that wasn't hooked up on my old router, I"m just trying to get what I had on the old router to work on the new one. Everytime I call support, they have me change something that messes up what a previous agent had me do. Now they want me to pay for a direct connection so they can upgrade my router firmware...they didn't even ask what version I already had which happen to be the same version that is available on [URL] so if I had agreed, I would have paid for nothing. I had already paid $29.99 for additional 14 day support on my old router only to find out I needed a new one.
I've been using Linksys routers for quite awhile but I'm just about ready to change brands. I would really like to give this E-2500 a chance.
When I plug in my Belkin my Netbios over TCP/IP is enabled, however is disabled when the router is connected. I cannot gain access to internet through Belkin G router, but can through my ISP router. I've tried IP/Config/all, (Nothing). The problem started when I changed something in Firefox (About:Config) attempting to change URL Search engine from Yahoo to Google, and that's when the problems started.Now my (Desktop) Computer doesn't recognize network, and I can no longer gain access to Net w/Belkin G wireless router...however, router will allow temporary access to internet when plugged up anyway (2 Android phones, 2 laptops), but the desktop will not connect.
View 11 Replies View RelatedRecently the home wireless network was upgraded to 802.11n with WPA2-PSK security. There are currently 3 laptops successfully connected and running the internet.
I have a desktop computer that recently had the NIC card upgraded because beforehand no connections were being recognised. Now there are connections being recognised but when I go to connect to the home network (Which has full signal) it begins to connect, it says "Waiting for Network" then after 2 or 3 minutes it just stops, no error message or anything. Ive also tried moving the tower closer to the router but this also does not work, it begins to connect to the network and then stops and says "Unable to connect to wireless network".
Another thing that might be of use, I am unable to access "ipconfig" in the terminal, I type "ipconfig" in run, then the terminal will pop up and close instantly.
My network consists of a main computer connected to Internet via cable and a modem. I also have an xbox 360 connected via the modem's wireless. I am using a netgear wireless adapter for the xbox, I also have another pc in the same room as the xbox, keep in mind the main pc and these others are multiple rooms apart. Now my issue is that the other pc is not recognizing the wireless adapter, and I know the adapter works because I've been using it on the xbox and it works perfectly. Now I went into connect to and it's not showing anything wireless or netgear associated.Also forgot to mention I am using the same adapter for both just unplugging from one and connecting to other.
View 14 Replies View RelatedWe have recently bough a couple of the new C3560CG-8PC-S switches, but they are not being recognized by the LMS 3.2;Is there any patch or device firmware I can update on the LMS to have support of that switch on the LMS 3.2 ?
View 1 Replies View RelatedSigned in to the network place and have an excellent signal. When I go to internet explorer it says that no way. I have a desk top and Vista. I believe I can probably get there simply if I just know how. I am showing that the wireless is up and ready to go. Have gone to all the tools and control desk.
View 5 Replies View RelatedI set up a network several years ago. The network was to use a printer between an old desktop with XP and a laptop with Vista. This has worked very well until several weeks ago. I would logon to the network on the laptop through the desktop, type in the password and I was good to go. Suddenly the password does not work. The printer works fine through the desktop. We have had several lightening storms in our area recently.
View 14 Replies View RelatedYesterday I booted up my new custom desktop and today I installed my wireless PCI card. The drivers are installed and it recognizes one or two networks in my vicinity, but my home network and probably about 10 more are not showing up. I tried re installing the drivers but no luck. I was able to get my network to appear about 50% of the time I searched. I also was able to rarely establish a connection, but the speed was extremely slow and was lost in less than a minute.
View 2 Replies View Relatedmy win7 is not recognizing any wireless network
View 1 Replies View Related