Is there a way or software can I use to send messages to all wirelessPCs in my network without doing any configurations or installation on those PC.I've used net send command for that, but is there another way?
i need to be able to find out what application/service is sending out net bios broadcasts on a network segment the requests are for machines that no longer are on the network but something is trying to obtain there ip address as they are not in dns any more i am assuming this is why they are resorting to netbios broadcasts i need to some how isolate what application or service is trying to find out.
I can't connect to the internet. When I double click Local Area Network under Network connections it says it has both sent and received packets. It is set to automatically acquire an ip address. The computer is connected to a router. I can ping 192.168.1.1 but when I try to reach my router's settings it says page can't be loaded. I tried to hook the computer up directly to the modem and connect that way. It said it was connected and it was sending packets but I still couldn't do anything. I've turned off the windows firewall. The computer is Windows XP SP1
I can't connect to the internet. When I double click Local Area Network under Network connections it says it has both sent and received packets. It is set to automatically acquire an ip address. The computer is connected to a router. I can ping 192.168.1.1 but when I try to reach my router's settings it says page can't be loaded. I tried to hook the computer up directly to the modem and connect that way. It said it was connected and it was sending packets but I still couldn't do anything. I've turned off the windows firewall. The computer is Windows XP SP1.
More info: ip config /all netstat -n ping&tracert 192.168.1.1
For a customer I have configured a new ASA 5505 firewall with 8.42 software. I had to build 3 ipsec tunnels to different locations and firewalls. All tunnels are working except one. I have to translate the inside network 1 to 1 to a different private range before it is sent over the tunnel. Each host from network 192.168.133.0 /24 has to be translated to a 192.168.112.0 /24 host and then sent over the tunnel. (e.g. 192.168.133.22 translated to 192.168.112.22)
It did work ok but not now.Even after I put the setup disc into it, it does not show that it has recognised the router. I can only get it to work by using an ethernet cable. I tried to install my router onto it and it came up with a message saying it had "two network adapters, please click on one of them" or words to that effect. It didn't show anything to click onAlso she has recently bought a new desktop computer (Windows 7) and when I was looking into the routers settings it is still showing her name of the old PC she has scapped in the Network. Therefore on the BASIC NETWORK INFORMATION screen it says Network 2. I know this is probably not important but if she ever buys a new PC in the future it will show Network 3So what can I do to get rid of the old computer name on the router settings?
I have a Asus EeePC SeaShell 1005HA-H and i have a LINKSY ROUTER in my home. I recently been having problems with my wireless internet. I know it isnt the router because i have went to my boyfriends house and my laptop usually automatically connects to his internet and the same message continues to show up "Acquiring Network Address message". I try to repair the network and a error comes up. Then i went to check the firewall settings and the firewall is tured off.
I just recently bought a new HP Envy m6 laptop that's not even close to a week old yet and I've run into problems with the wired connection. I have two different belkin ethernet cable cords to use and neither of them seem to be connecting whenever I plug them into the ethernet socket on my laptop. I've tried uninstalling the network adapters and updating the drivers. None of that seemed to have solved my problem so far.
Is there anything that I can do to solve this problem? I would be fine with the wireless connection that I'm currently using if it didn't fluctuate so horribly. I live in an apartment complex that provides internet access to me so I don't know what company they are using nor the router that is providing me with the wireless connection. I will be checking in with the management to see if it's not a problem with their internet tomorrow.
As for the network adapter itself, I have a Qualcomm Atheros AR9485 802.11b/g/n WiFi Adapter and a Realtek PCIe GBE Family Controller. I'm assuming the Realtek adapter is the one that deals with wired connections. I'm currently running Windows 8 on the laptop.
I'm running a home network with 3 computers via a linksys router attached to a westell modem. Is there a local network messaging system I can use to pop a message on a screen to one of the other computers? Can I use DOS?
I received the recovery CD's from Dell and reinstalled the operating system, But now I can't connect to the Internet and get the message that there is no network adapter. What do I do now? Do I need to use the Driver CD and reinstall also? [code]
Same problem ' network cable unplugged' even if it is physically connected. I have sony vaio pczim series with win 2000 xp home edition with a broadband (cpe adsl2+ type) connection. While everything working fine for past two years, suddenly after a thunderstorm night, I noticed the network connection failure with the message. I checked the router, cable and the same are working fine with other hp laptop. Even the vaio is running with the same router while usb port is used and even the wireless and bluetooth are fine, but network with ethernet cable connection does not.
So I have an issue with getting a laptop hooked onto the router signal. The router is a brand spankin new Linksys EA4500 and the laptop is an IBM which is running Win XP (not sure of SP version as it is a customer's comp. at a hotel I run). Anyway, the error message I am encountering is:The network password needs to be 40 bits r 104 bits depending on your network configuration. This can be entered as 5 or 13 ascii characters or 10 or 26 hexadecimal charactersAt first I thought is was my router password since it contained a $ symbol so I changed it to only letters and numbers but still didn't work. I have never encountered this error message on any laptops and no other rooms have been affected.
My roommate has just gotten a second hand laptop and he's trying to connect it to the Wireless network so that he can browse the internet from his room.However, although all the settings are correct, attempting to connect to the network loops.It comes up showing the Wireless Networks available, I select the network and click connect, it then asks for the encryption key. I enter the key and hit connect again, it comes up with the 'Connecting' pop-up and then loops back to the Available Networks screen again.There are no error messages, it just goes back to the starting screen and it hasnt connected.The Laptop in question is a Lenovo T60 with a Intel PRO/Wireless 3945ABG card.The router is a TP-Link TD-W8960N.
Laptop connects to wifi network. But it shows "No Internet Access" message.My Macbook connects to the internet just fine and the wifi on my iphone works as well.The ethernet on the laptop works and I am able to access the internet this way. The laptop does connect to some of the other access points but I've had issues with my router.I tried the usual debugging mechanisms - disable/enable adapter, reset the router, reset the tcp/ip stack. [code]
I have a Netgear WNR612 wireless router, which worked fine for a few weeks. Then something happened and I can't keep the connection anymore. It happened right after I used iTunes to update my iPhone, perhaps a coincidence, but I'm mentioning that just in case. Internet still works fine with ethernet cable straight from the computer, only the wireless connection doesn't work. This happened about a month ago and I haven't been at home much to fix the problem. I have turned off and unplugged everything for several days at a time while gone. I get a Network Error message saying, Windows has detected an IP address conflict. I have tried restoring the router back to factory settings and reinstalling the wireless card. I have tried changing the IP address settings both in the Network and Sharing Center and the router admin page. What I think I should do is change the IP address in Command Prompt, but when I type "ipconfig /release", it says "No operation can be performed on Wireless Network Connection 2 while it has its media disconnected" and the same for Local Area Connection. I don't understand what this means, because there is a wireless key in my keyboard and there is a white light (not orange) like there should be. Also in the Network and Sharing Center, I can see that the connections are enabled.
I'm new to IT, and have been put in charge of managing our servers hile my boss is on vacation.We currently have a Sonicwall Network Security Appliance that handles our Firewall/VPN and have web content filtering set in place.I have a user who belongs to 2 CFS policy groups that we have set up. I've double checked with Active Directory, and he is a member of both groups.
This person SHOULD have access to Job searches/ and Restaurants,but receives a "content blocked" message on his browser.It appears to me that the settings in Sonicwall are correct, as well with AD member groups.
One Day the internet is fine the next day The Internet Stopped working. The problem is my pc is sending packets but not receiving any i though it was a bug or something so i restarted my pc after i restarted my pc the internet was working fine until a couple of minutes passed it stopped receiving packets again.i tried resetting the modem but nothing worked.I tried winsock fix or resetting TCP/IP and stuff but nothing workscause its starting to frustrate me.
Our computer is sending but not receiving packets. We've tried 3 different wi-fi adapters, and that wasn't the problem. We have no idea what's wrong? It won't pick up any wireless signals by the way, and it works fine while connected via Ethernet.
No School havn't own email server, Just we want email within the Lab. (There are 20 PCs on all PCs Windows XP (Service Pack 2) & MS Office 2003 installed.Now tell me how can we send/receive email via using outlook.
I had a customer call me and her desktop (wired connection only) is sending and receiving packets but she still cannot connect to the internet. Customer has tried power cycling her modem, router and desktop with no avail. Her system is running XP.
Alright, so we have about six computers on average all on at the same time, working just fine, last night one of the laptops just, stopped working, saying there is no internet access, With every attempt it doesn't send any information. When I disconnect it from the wireless, then reconnect it, it immediately receives packets but won't send any.