Asus RT-N13U Firmware Restore After DD-WRT
Jan 27, 2013
Yesterday, I flashed DD-WRT, latest beta version, to my router, an Asus RT-N13U B1. After flashing DD-WRT, I couldn't get the 3G USB modem to work with it, and thus, I decided to flash back the original firmware onto it. I needed to put it into restore mode, but it was just not going into the restore mode. Then I read somewhere that after installing DD-WRT, other people had the same problem. [URL] So I connected to my router via telnet, using PuTTY, and ran the "mtd erase linux" command without the quotes. Even now, it isn't going into restore mode.
View 11 Replies
ADVERTISEMENT
Feb 8, 2013
I can get my router into recovery mode, and after disabling all other network adapters and setting a static ip on the one I use to connect to my router, I was able to get into it using the Firmware Restoration Utility.But yet another problem is being faced now. When I try restoring the firmware, it goes up to 51%-54%, it varies, stays like that for like 10-15 seconds, and then throws this error message : "Failed to upload the firmwarecheck the connection between your computer and router."
View 3 Replies
View Related
Dec 10, 2012
I flashed my router to DD-WRT, but I could not access the web UI which is suppose to come on typing 192.168.1.1 in the web browser. . It used to come fine before but I reflashed to Asus Firmware but now I cannot access it. I have tried several times to flashing it to Asus Firmware and Back to DD-WRT, but it didn't work. When I flash to ASUS everytime my old settings are still the same. I tried assigning a static IP also.
View 1 Replies
View Related
Dec 12, 2012
with TFTP upgrade SRW2xxG4_FW_1.2.3.0.ros and WEB interface after the restart, the switch will not start, display HyperTerminal link. You can also restore the switches do not?
View 1 Replies
View Related
Dec 27, 2012
I have an E4200 router with 3 WET610N access points. I did the firmware update on the E4200 router about 2 weeks ago so my son could use his xbox when he got home after 4 months of being away. Everything seemed to work OK as far as I could tell....but when he went to sign into xbox live and watch Netflix, it will load to 98% and stop. A friend of his came over with the new Slim xbox 360 with built in wireless and it will connect fine on its own, if we hook up one of the 610N's to it, it will load to 98% on Netflix and stop again with error code R8152. Both of my older xbox's will hook up and play on xbox live, just not work with Netflix.
I also noticed, it shows the WET610N as a hard wire on xbox and will not search for any wireless networks, I have 2. The newer Slim xbox360 will search out both networks on its own if you allow it to use its internal wireless. This only happened since the firmware update. And this equipment was working fine before this. Is there a way I can restore the previous version of firmware?
View 4 Replies
View Related
Jun 16, 2008
I purchased a WRT160N router last Friday. After setting it up, everything seemed to work fine, but after a couple of hours, the router stopped responding to any requests. The LEDs stayed on as if nothing had happened, but the router was dropping everything coming from both the WAN and a wired LAN interface. Since than, I had to restart it 3 times during the last 3 days.The firmware is 1.53.0, which seems to be the latest firmware for the European market - even when I try to get a newer firmware, this site only offers the US version 1.02.2.Should I update the firmware to the US version 1.02.2 ? Is there any difference between the 1.53.0 and the 1.02.2 version ? Is there a way to restore the original firmware in case the update fails ? I haven't found any link to 1.53.0 version..Also, does this firmware updating affect my warranty ?
View 9 Replies
View Related
Aug 13, 2012
3 times in the last 2 hours i have had my new rt-n56u give me the message.You have set the wrong dynamic or static IP address for your RT-N56U.
So i reset the router and it pulls the same IP and info it had before from my ISP.Doing some reading it seems some people have had this issue occur over and over.I am upgrading to the new Asus1.0.1.8i from 1.0.1.8f which is installed now, but wanted to ask if i have other options for this router as this problem gets annoying..Example i am used to DD-WRT for my linksys wrt- models..does the NT56U have something similar...
View 2 Replies
View Related
May 10, 2013
I just got a new Asus AC66U. When I play games I have severe stuttering now using the 5Ghz band. I ran a ping to the router and every 20-30 seconds it jumps up from 1ms to 100-900 for 2-4 pings then backs down. I tried running ping test on two computers with the same result.I tried fixing the 5Ghz to a specific channel. I've tried upper channels, lower channels, I've adjusted the channel width from 20-80Mhz. I've changed the preamble from long to short, I've upped the transmit power, I've turned off PnP. I haven't been able to change a setting that made a difference.
I did notice that the lag spikes were much less frequent in the morning when I tested, before everyone was using the internet, although I saw an occasional ping spike. They must be related to router load.i don't want to change the firmware on the router in case I have to return it. I spoke with Newegg and they're going to send me a replacement router. I doubt that it's the hardware, but this will be a good way to know for certain that it's not the hardware. Once I get the new router I'll test everything again including trying the ping with a LAN cable.
View 5 Replies
View Related
Nov 27, 2012
I have recently acquired an ASUS RT-N16 router. My original plan for it was to install Tomato on it. However, after checking their website i found out that the firmware was not updated in the last 2 years. There seem to be a few updated mods but none of them really seemed mature/stable/well-documented.
I would like to know what other people recommend as open-source firmware for this router. I know the answers will probably be subjective; so i will give a bit of background on my needs:
for now i will only use the Wi-Fi on an Android phone the connection will not be shared with anyone (so QOS is optional)i want a stable (wired) connection on my PC (for online gaming etc.)i want the (wired) download/upload speeds to be as close as possible to those achieved by directly plugging the Ethernet cable to the PC's network card; i have a 100 Mbps connection my ISP uses PPPOE my technical level: i am a software developer and i have good knowledge of bash scripting, but no experience with networking
Also, i know that i could probably just use the stock firmware (and maybe will use it for a while), but i'm interested in trying an open-source version (for more features, flexibility, as a learning exercise etc.)
View 1 Replies
View Related
Jul 17, 2012
I have an ASUS Z77 Motherboard and when I install the AI Suite II which comes on the installation disc it blocks my internet connection. When I uninstall the software my connection is fine. I am using an Ethernet connection by the way. I think it is being blocked by the component called Network iControl. As soon as that component is uninstalled my Internet connection comes back. I want to have the software, but I also want to have my connection.
View 1 Replies
View Related
Oct 5, 2012
I recently moved into a larger 2 story house, and for the first few months I was using a Linksys E1000 I've had for about 2 years now. It's a fine single band router, but the people upstairs and the xbox/PS3 in the living room didnt have the strongest connection.
I shopped around and finally got a ASUS RT-N66U for a really good, strong dual band router that would supposedly give better range and performance than my old E1000.
Unfortunately, since I got it everyone is having issues they never had before, namely:Signal dropping all around the house and having to search for the network much slower performance than before the xbox/PS3 cant hold a stable connection even for a few minutes now, when before you could watch Netflix HD programs easily
I've upgraded the Firmware to 3.0.0.3.178 since I heard earlier firmwares had issues, but other than that and opening my ports for qTorrent it is relatively stock settings.
View 2 Replies
View Related
Aug 9, 2011
I think I've done a wrong move and cancel my company e-mail address.I'm not familiar with this , but is it pssible to restore.??..and if so be as clear as possible for each step to do cause I'm not a computer wiz in that stuff.
View 1 Replies
View Related
Jul 31, 2011
The problematic PC is AMD triple core, with ASUS M3N78 motherboard and xp professional. PC should connect to internet through the router, TP-Link TL WR340GD, along with 3 other PCs which are all working fine. Basically, the PC caught a virus and I performed system restore. After that, the PC was working fine, except that there was no internet connection. I tried to reset winsock from command promp, but that did not sort the connection problem.I noticed that the yellow light on the back of the tower, for the ethernet cable connection, is yellow when the cable is not plugged in, however, as soon as I plug the ethernet cable in, the light disappears. The same cable is working fine when connected to other PCs so it does not seem to be the cable problem. The information in Network Connections says Limited or no connectivity. Full messages when prompted says: "You might not be able to access the internet or some network resources. The problem occurred because the network did not assign a network address to the computer.To restart the connection and try to establish full connectivity, cliick Repair." and then, after clicking repair, it says:"Windows could not finish repairing the problem because the following action cannot be completed:Renewing your IP address.For assistance contact the person who manages your network."I also tried to release and renew IP address from command promp, but that did not work either.
View 19 Replies
View Related
Sep 7, 2011
I'm trying to restore my IP address because my boyfriend's at work and unfortunately not I've been following all the directions I can under this articlebut I get stuck at just the first step! When I hold the Windows and R buttons down and type in command the computer says it can't find that program and also when I open my network sharing center it won't let me right click on it anywhere to get to properties so that
View 2 Replies
View Related
Aug 9, 2012
I just reinstalled windows and am trying to restore my previous settings. I was wondering how to do that, specifically with the bookmarks.I originally saved my bookmarks with an export, and I have the saved file.I cannot seem to get my bookmarks back. I have tried all of the options.I am using the internet browser, google chrome.
View 2 Replies
View Related
Feb 18, 2012
How do i restore my password for D-link Model No.Dl-614+
View 1 Replies
View Related
Jan 3, 2012
I am trying to restore my pc to a previous date but the calendar that displays will not go back to December - it is stuck on January.
View 1 Replies
View Related
Jul 5, 2010
I'm trying to do a restore from one v5.1 box to another. The file is sent via ftp from the configured repository but when the file is sent I get an error saying failed to unpack.
My restore box is running an evaluation version at level 5.1.0.44.3
View 1 Replies
View Related
Apr 11, 2012
We have cisco works LMS 3.1 and the server have very problems, we need format the server and reinstall the Cisco Works, when I doin backup and restore of data LMS We lost the licenses? or when we restore the data in the server we have the same licenses? or get the new licenses to cisco?
View 5 Replies
View Related
Aug 29, 2011
If i reinialize(restore) the cmf database.do i need to reinialize all the databases.???
or if i reinialize the cmf database and do bulk import the devices is enough?
View 3 Replies
View Related
Sep 21, 2011
My wireless adapter isn't recognized on my computer now :( it was working perfectly before. My computer keeps saying there is no driver for my adapter?
View 1 Replies
View Related
Jun 12, 2011
my name is Nathan and I have ran into an issue with my LAN. I recently did a factory restore by pressing F11 at start up due to corrupted Windows files. Now that I have restored my computer, I get a "limited connectivity" to an "unidentified network" I tried all the Windows repair options, I powercycled my modem and my router and I unplugged and replugged my LAN cable.
View 9 Replies
View Related
Jan 27, 2013
I use a dongle from my ISP as my main internet connection source. I needed to do a full system restore because one of the windows system files got corrupted.After the restore, my internet connection was extremely slow. I restarted the computer and I got my normal fast speed but only for about 10 minutes and it is now very slow again (about 10 mins to load Google home page, for example).Internet speed was never an issue before the restore. Also I tried the dongle on my work laptop at home and it's fine.I'm using Windows XP. I've tried everything suggested at Slow Computer/Internet AFTER complete system restore but it is still slow.
View 5 Replies
View Related
Apr 11, 2011
i deleted my built in wireless connection by accident. how can i restore it
View 1 Replies
View Related
Sep 20, 2011
A I went over to a friend's house to fix some problems with his computer. He has a Windows XP Home Edition desktop. I used System Restore to fix some kinks with it, and now the computer has no Internet access, and I have no idea how to get it back. I tried reversing the System Restore and turning it off, but that's not working. They said that the connection was fine, but that the computer could not read the modem.
View 1 Replies
View Related
Aug 31, 2012
I went to a thread with the same name as this one and tried all of the things in it but it still won't work, although some programs now work a bunch of other ones still can't connect since the restore.
Code:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Mariama-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 12 Replies
View Related
Nov 19, 2012
I wonder how i can restore my router to its defalt settings if my reset button is broken and the router has lock the mac of my pc. Can i connect the router to my pc and access it from it?
View 7 Replies
View Related
Apr 28, 2012
i installed fresh lms 4.2 on new machine and i amy trying to restore lms 4.1 backup via CMD.
View 1 Replies
View Related
Aug 24, 2011
I was trying to erase my lab router 2600 and reset it back to the factory defaults. Well I was able to to reset it all right but I used the erase command which worked a little to well. So now there is no IOS and the router is in ROM mode and I didnt back up the pervious IOS "Nice". So was able to get an updated IOS for my 2600 but I'm trying to install it and don't know how. I was able to get a tftp server app for my windows pc but I'm unsure on how to configure it so I can transfer the new IOS to the router. On the up side I did learn something erasing and reset are to very different things.
View 6 Replies
View Related
Aug 21, 2012
I am facing a failed issue when restoring the WCS Database. Below is the error i get, does any one out there facing it before?
#######################################
[root@egwgwcs WCS7.0.220.0]# ./Restore
Please enter the full path of the backup file name: /opt/WCS7.0.220.0/Backup_File/WCS_Aug2012.nmsbackup
Untaring the backup file...
Failed to untar backup file. Exception: invalid stored block lengths
Restore database failed.
#######################################
View 1 Replies
View Related
Jan 8, 2012
I want to restore a backup from c2960 to other one.Why is recommended to remove any security commands, like AAA?
View 2 Replies
View Related
Dec 12, 2011
I seem to have lost all portlets under the monitor dashboard in lms 4.1. I am not able to add any either. Is it possible to restore theese portlets in some way ?
View 2 Replies
View Related
Oct 20, 2011
I've been setting up building and testing our new ACS 5.x boxes and I've been running into a spot of bother with the backup restore feature. This most likely due to my unfamiliarity with the tool.
As part of my testing for Backup/Restore, I first backup the data using the Removal and backup tool in Secure ACS View (found under data management. I then confirm that the new FULL backup has been populated my test repository and is available in the restore feature. (also under Data Management) My next step is to create a few test Network Device Groups, Identity groups, and users Then I go back to the restore feature select the Back up file I just created, I also check the box Skip View Database backup before Restore and hit the restore button.
The box goes through the expected steps including a reload. When it comes back up I would expect the test users, groups etc I created after the last backup to be gone as they did not exist at that time. Although I find the opposite is true. Any settings I made after the last backup are still present. I do not have incremental backups enabled.
I essentially want to test a backup of the database of users and groups/rules etc make changes and then restore that database to the previous backed up configuration.
View 2 Replies
View Related
