Cisco :: BBSM-1190-K9 - Way To Upgrade BBSM Memory
Aug 20, 2012
We have an old BBSM server (BBSM-1190-K9) with win2000, that we hopefully will replace soon with ISE.I have tried to upgrade the memory in the server but the problem is that the server refuse to start after I have changed the memory.The original memory capsule is Apacer 512 MB ECC PC2-5300CL5, and we have tried with this.
Corsair Server DDR2 PC5300/667MHz ECC Reg. CL5 2GBand MT18HTF12872PY-667D2 BTC 1GB 240p PC2-5300 CL5 18c .There is no response at all on the screen, not even any pre boot messages or BIOS . Power on button only blinks slowly.
View 2 Replies
ADVERTISEMENT
Apr 25, 2005
i have a bbsm server I'm bringing up on line. Trying to add the first site, i configured everything i think right, but the client gets a network error page, and the event log shows:
EventID:28
Source:BBSM_AtNotify
Description:
Failed to locate client ip:10.233.1.10 MAC: 00 00 00 00 00 db on any network device.
i did a debug on the AP1200 (12.3(4)JA) i am using and see that the bbsm is talking to the bbsm. I just can't figure out what i am doing wrong.
[code]....
View 2 Replies
View Related
Mar 24, 2011
Upgrading the memory on an 1841. After inserting a 256MB/PC133/SDRAM/DIMM it would not post during the boot, hangs.If i take out the chip it works fine.The on-board memory is 128, so the 256 is the max it would take to a total of 384. According to the documentation this should work.The memory chip is a Transcend chip, basically Samsung.
View 2 Replies
View Related
Jan 30, 2013
I wanted to know how many sodium memory slots the 1841 Routers have so i can upgrade to more then 128mb of DRAMI want ideally 256+on the Cisco website in the diagrams they dont say if it has 1 or 2 slots
View 8 Replies
View Related
Jan 30, 2012
I am trying to get experience with 8.4 code on my 5505. I purchased a Cisco 512MB memory upgrade and installed it. It booted up once and I thought I was ok. I then looked down and noticed that all lights were blinking on the front panel and I had no console access.
[code]...
View 5 Replies
View Related
May 11, 2011
Trying to figure out if I can upgrade this flexwan to 256MB and not sure is the card below already has 256MB total or 1 64MB per PA equaling 128MB total.
View 1 Replies
View Related
Feb 25, 2012
Currently I have C2801 with 256MB of memory and 64MB of flash. I want to upgrade it to 384MB / 128MB.Do I need to get MEM2801-256D or I can use any PC133 SDRAM (144PIN) for memory? 384 is maximum I can install? Do I need to get MEM1800-128CF or I can use any compant flash card? 128MB is maximum I can install? (I saw 256MB flash on for C2801)
View 10 Replies
View Related
Feb 20, 2013
I am upgrading 6500 switch from old ios to new one and the new one requires 512/512 memory to be free below is the show ver and sh sup-bootflash,
sw-cta2-i8-off>sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-VM), Version 12.2
[Code].....
View 1 Replies
View Related
Sep 16, 2010
I need to add memory to my ASA 55xx's (running 8.2(2)), some of which are config'd active/active or active/standby. The docs say that ram must be identical, which makes sense for production. My question is this: can I upgrade the standby units first, make them active, and then upgrade their mate? Or must I schedule downtime to take the pair down for the upgrade?
View 4 Replies
View Related
May 10, 2011
I upgraded our ASA5540 to 8.4, THEN noted the increased requirements for Memory. I purchased the 2Gig upgrade, but when installing in the Primary unit today, noted that there were 4 slots. Slots 1/3 had 512Mb modules, so I installed the 2 x 1Gig modules in slots 2/4.
The ASA5540 came up clean, and it "sees" the entire 3Gig of memory.
My question: Is this a SUPPORTED configuration? All documentation I have read only mentions 2Gig of memory. Also, If I had FOUR x 1Gig memory modules, would the ASA5540 support the 4Gigs of memory?
View 1 Replies
View Related
Jul 6, 2011
We want to run ASA 8.4.x on an old ASA5540. We need to upgrade its memory to 2 GB with the following memory upgrade: ASA5540-MEM-2GB=
I suspect that we will completely remove the existing 1 GB of memory and replace it with 2 GB. If this is the case, can I use this 1 GB of memory removed from the ASA5540 and put it in a ASA5510 instead of buying a ASA5510-MEM-1GB= for the ASA5510?
View 2 Replies
View Related
Aug 29, 2012
I have DSL 8Mbps DL and 768kbps UL,Internet -> Modem -> Cisco Router -> Firewall -> Switch Core - > Multiple switches like sfe2000p,CiscoRouter: i use port gig0/1 for PPPoE and i use port gig0/2 for LAN static,Router port gig0/2 with 122.54.144.153/29 connected directly to Firewall port13 with 122.54.144.154/29,i want 122.54.144.153/29 will my default gateway,Please include no limit bandwidth,filter etc at router, Firewall will be DHCP Server and control the bandwidth, filtering etc and the client computer should get 8Mbps.
View 2 Replies
View Related
Nov 7, 2011
I tried last night to upgrade the memory in my old 5510. It's about 5 years old and has the single memory socket. I followed the instruction included in the kit:
Mfr. Part#: ASA5510-MEM-1GB
I did wear an ESD wrist strap (genuine Cisco at that!) and ensured the memory was fully seated, the handles locked in.Upon restarting the ASA, for over 15 minutes, it stayed in mode: Power LED steady, Status LED flashing, other LEDs off. No response to attempts to SSL via Putty. I powered it off, verified the memory was indeed fully seated, and re-installed the original 256 MB module. It powered up normally in less than 5 minutes. Is there anything else to try before returning the memory? Tonight, I can try the same new memoy module and see if it works.
View 3 Replies
View Related
Mar 1, 2013
I recently upgraded the flash and the RAM on one of my ASA 5505 lab machines. The flash was upgraded from 128 to 512MB and the RAM was also upgraded from 256 to 512MB. I am using asa845-k8.bin. The firewall boots and runs file until you issue the reload command. The system shuts down but never reloads.
View 11 Replies
View Related
Oct 21, 2012
I have Catalyst 6509 E with redudant SUP720-3B (and MSFC3) running 12.2(18)SXF6 IP Services Lan Only IOS (this IOS requires 512MB DRAM and 64MB of flash) SUP has 512MB DRAM (458720K/65536K) and 512MB sup-bootdisk:, but, there is65536K bytes of Flash internal SIMM (Sector size 512K).
My question is can I put 12.2(33)SXJ3 IP Services Lan Only IOS to this 6500 because this IOS requires 512MB DRAM and 512MB od flash?This is "sh ver" and "dir all-filesystems" of my 6500:
cat6500#sh verCisco Internetwork Operating System Software IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(18)SXF6, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2006 by cisco Systems, Inc.Compiled Mon 18-Sep-06 23:59 by tinhuangImage text-base: 0x40101040, data-base: 0x42D90000
ROM: System Bo
View 6 Replies
View Related
Mar 5, 2013
I upgrade the IOS of my switch 3560 from C3560-IPBASE-M), Version 12.2(25)SEB4, To C3560-IPBASEK9-M), Version 12.2(55)SE5 after that the utilizatio of the memory increase to 80% I attached the output of show memory statistics history
View 5 Replies
View Related
Apr 4, 2011
I have an Acer Desktop Aspire AM3100 running Windows 7 Ultimate. I upgraded my memory. When I turned the PC back on I had lost my whole home network and cannot get internet acces back. I have checked my modem by direct connecting it to my laptop. I have checked my linksys box by doing the same. I can see the linksys on my laptop but cannot access the internet. On my desktop I get nothing?The home network and internet access all disappeared when I upgraded memory.
View 2 Replies
View Related
Mar 5, 2013
I have ordered RP2 and it will be having 8GB default memory. What is the difference between memory & Physical memory?Since I am able to see only 4GB memory in my ASR 1004. [code]
View 1 Replies
View Related
Feb 22, 2012
i have cisco ASA 5510 Firewall using in my network, i have planning to upgrade the Flash memory from 256 mb to 512 mb and the RAM from 256 mb to 1GB.
View 1 Replies
View Related
Sep 29, 2011
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies
View Related
Jun 19, 2012
I am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
View 6 Replies
View Related
Oct 12, 2011
What causes LMS 4.1 to have high memory utilization?
View 4 Replies
View Related
Jun 15, 2011
it is possible use 1 or 2 Gb memory with ASA 5505 or only 512 Mb ?
View 3 Replies
View Related
Apr 19, 2009
I am doing the initial configuration on our ASA 5510 to use our Radius server just as our 3005 VPN Concentrator did. I can do the test connection inside the ASA with no problems, and when I authenticate using the Anyconnect client, it appears to authenticate fine, but then dumps the connection with an error stating there is not enough memory in he ASA to allow this connection, the error message is as follows:
Error Message %ASA-4-722004: Group group User user-name IP IP_address Error responding
to SVC connect request.
Explanation There is not enough memory to perform the action.
Recommended Action Purchase more memory, upgrade the device, or reduce the load on the device.
Can this really be the case with no connections active, a single user attempting to authenticate through Radius and an out-of-the-box ASA 5510?
View 3 Replies
View Related
Sep 2, 2012
The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
View 3 Replies
View Related
Oct 4, 2012
We have recently purchased a brand new RV042G VPN router, set it up, and had it running for a while without issues.
Now that we are actually trying to use the VPN functionality, the router becomes unstable after a while, showing "out of memory" lines in the logs, and after a day or two the VPN stops working completely and the web interface becomes completely inaccessible.
This issue happens when using any sort of VPN that's supported by the router.
View 1 Replies
View Related
Jul 6, 2011
I've deployed many Cisco PIX 501 v6.3.3 either as normal firewalling feature and/or with VPN features enabled. I noticed in all my deployments, regardless if it's during peak hours or after office hours, the memory utilization is always consistent 11MB utilized over the total of 16MB(memory default size).
View 3 Replies
View Related
Sep 18, 2011
I want to upgrade my IOS on an 871W. In order to do this I need to upgrade the memory. I have found that I need the MEM870-32F (Am I correct?).
As in here: {URL}. So if I follow these instructions: {URL}. Is that all there is to it?
View 1 Replies
View Related
Dec 16, 2011
we have some unusual issue when our core 3825 series router dealing with NAT !first off to offload traffic we have two router one 3825 and other 2821 configured to support GLBP .
interface GigabitEthernet0/0
ip address a.b.c.d 255.255.255.0
ip nat outside
ip virtual-reassembly
[Code]....
The problem is router hangs out , intenet users suffer slowness , criticle service like telnet doesnt work . the only solution i found is a reload ,not to mention this is core router sitting on campus network edge . and servicing around 1000 users !! approx assuming all users have using internet at same time .
how to check , if memory is not sufficient ?further if any users using utorrent or any thing like that , does it make enormous no of connections form same pc ?
is their any licence requird for IOS IPS ?i prefer to turn this feature on to kill torrents connections ? but i fear crashing of router as no of users are huge !any know bug with glbp , nat with ip voice image C3825-IPVOICE-M VERSION 12.4(24) T4 ???
View 3 Replies
View Related
Jan 30, 2012
To have a management tool polling by SNMP some information like CPU load and memory load, I tried to find out the OID.The supervisory card is a WS-X45-SUP7-E with a dual core CPU and 2G of memory.IOS is IOS-XE 3.2.2
Does any OID or nagios template already for the new card ? The Nagios template I use for others switches do not get the good field
View 3 Replies
View Related
Mar 15, 2012
I'm working on a distribution config for some routers with a software IPS. The problem I'm running into is the final [confirm] during setup. Is there any way to disable confirm messages in IOS?
View 1 Replies
View Related
Jun 1, 2011
Cisco 3845 router (256RAM / 64Flash), increases the cpu utilization upto 70~80 percent, during the time of high utilization, I am unable to run show command on router.The configuration is simple, this is connected with two internet links (24Mbps and 8Mbps) and its about 600~700 users are using internet.show version, show memory and show process cpu outputs are attached here.
View 7 Replies
View Related
Feb 5, 2013
Any known problem with the DRAM on 2800 routers? Over the past few months we have had four 2800s fail to reboot after power off/on and in all cases this was due to faulty DRAM. All four routers had been working fine for months with no problems and only failed after being rebooted. They all failed when trying to load the IOS into memory and therefore all got stuck in rom mon. The compact flash cards were all ok as a working 2800 booted up using the flash from the faulty routers. I haven't seen a field notice so are we just unlucky here?
View 0 Replies
View Related
