I am trying to setup my printer using the USB port on the router. I installed the share-port utility 32bit and every time i try to connect to the printer from my desktop the computer crashes and i get a blue screen.
View 14 RepliesI have the DCS-930L camera. I need to know how to setup port forwarding/triggering on my router, which is a Cisco DDR2200 CL. I understand that in order to use the camera, i need to do this. how to set up NAT.
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
ISP : TalkTalk
I'm getting to the last barrier to my Router USB printer working..The UPS is seeing my printer now but the last hurdle is the Printer Setup program. It is not comatible with Windows 8 apparently. The one I downloaded of the support site doesn't run either. Any news off one coming out for Win 8?
Region : Germany
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 121127
is it possible to use the Print Server on the TL-WR1043ND without installing the "Printer Controller Utility"? I have a HP LaserJet 1022 (in compatiblity list) connected which is recognized by the TL-WR1043ND. I want to connect the printer manually to my Windows PC using standard tcp/ip port, but I can't get it working. I tried RAW with Port 9100 and LPR with lp1. What are the right settings??
Region : Hongkong
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
When using the USB printer port share function, I found that some PCs, which had never physically connect to a USB printer before, will not have the virtual USB printer port in the port selection. In this way, TP-Link's USB printer controller will not be able to setup the connection. The PC will not be able to use the shared printer from my WDR3600.how can I create a virtual USB printer port in the remote PCs (without need to physically connect a printer to them) or other method to use the shared printer?
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View Relatedconnect usb printer to d-link n2760 router i plugged in the printer diagnsotic failed
View 2 Replies View RelatedIm trying to setup a cable modem which is also a router that has a printer attached to one of its lan ports. From there it connects to another router which connects to other clients from there i have another router with a VPN connection with other clients. I would like to be able to see everyone on the network. How do I setup the routers in particular the router with the vpn which is the last router. Also the vpn router is connected through its WAN port to the router ahead of it at its lan port so it can use its VPN connection.If it makes it easier lets ignore the cable modem as router and ill find the printer another way of connecting but essentially i need the two other routers for two ip addresses. One for the first router with my regular IP and then the other is for VPN IP.
View 3 Replies View RelatedRegion : Australia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0
Build 120926 Rel.27100n
ISP : Bigpond
I am trying to setup port-forwarding (6360 for IP 192.168.1.111 & 6361 for IP 192.168.1.112) on this TD-W8968 modem. But when I test it on [URL]. I get a message "connection refused".
How do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).
View 2 Replies View RelatedJust finished the setup for Canon MP780 USB printer to work with EA4500. Printer goes online only while it prints the pages. When I try to scan the document with MP Navigator it cannot communicate with the scanner as printer is essentially offline. How to setup the printer in order to perform the scan of the documents?
View 2 Replies View RelatedE4200 -
Can I use a USB hub to connect NAS ~and~ a USB printer to the single USB port?
I have just upgraded my Linksys router from an older one to the E-2500 about a week ago. Everything is working great on my wired desktop and 3 wireless laptops except the printer will no longer work from any of the computers. I've checked the printer wireless settings and they are correct (ssid and password) and it says it's connected to the wlan. Each of the computers shows the printer is active and set to default BUT the port light on the back of the new router is not on. I have changed cables and still no light, the printer is set up for sharing and it did work a couple days ago but port light was on then.
I have not added anything that wasn't hooked up on my old router, I"m just trying to get what I had on the old router to work on the new one. Everytime I call support, they have me change something that messes up what a previous agent had me do. Now they want me to pay for a direct connection so they can upgrade my router firmware...they didn't even ask what version I already had which happen to be the same version that is available on [URL] so if I had agreed, I would have paid for nothing. I had already paid $29.99 for additional 14 day support on my old router only to find out I needed a new one.
I've been using Linksys routers for quite awhile but I'm just about ready to change brands. I would really like to give this E-2500 a chance.
Can I connect my Canon iP6600D printer (USB 2.0 interface) to an Ethernet port on my wireless router so as to end up with a network printer?
View 1 Replies View RelatedI used a Belkin router for internet connection and connected to printer via ethernet cable. Belkin had frequent disconnects to internet, so I decided to use my D-Link DIR-655 router from another home. While it works well for internet, it will no longer connect with my printer, either via ethernet or wirelessly. I must carry my laptops to the printer and us a USB cable to get printouts. I am planning on moving to a Verizon 'hot-spot' and eliminate the routers completely soon and will maybe have this same issue. How can I resolve this matter?
View 8 Replies View Relatedd-lINK n-300 (DIR-615) Wireless Router HW/Ver: E1, F/W Ver: 5.00NA
I am having a problem with the DIR-615 router seeing my printer on a wired network. The printer is a Brother HL-2170W (also capable of a wireless connection). All other network PC's connect okay. I have attempted both wired and wireless connection procedures that came with the printer with no luck. The DIR-615 router does not see the printers IP address. How can I get the router to recognize the printer?
I'm finally jumping in over Christmas break to set up a Y network with three routers. I run a side business repairing and cleaning viruses/malware from PCs and would like the business subnet not to be able to mix with (and possibly infect) the "home" subnet.Before I knew what I was doing, I set up a simple two router "chained" network by hanging an old SMC router off my main Airport Extreme router, but I've since learned that's not ideal, since the "work" network machines can see everything on the "home" network. So, here's what I want to do. I want to put the new third router right after my cable modem (ISP). I want to keep my Airport Extreme and all devices attaching to it (home subnet) off one LAN port of this new router and my old SMC router off another LAN port of the new router (the test subnet). Currently, the IPs are: [code]My concern in setting up a "Y" configuration is that I have some wireless IP webcams on the Airport Extreme that are using port forwarding (both UDP and HTTP) so I can view them from wherever I am on the Internet, not just from within my home network.
What's the best way to make sure the port forwarding from devices on the Airport Extreme subnet works through the "new" router and out through to the Internet? Do I have to open the same ports on the new router? If so, does anyone have an example using the addresses above? Should I just put the Airport Extreme in the DMZ of the new router (so everything is just passed through - or will that allow my test subnet to see the home subnet? Some other way?
I have a D-Link wireless router DIR-524( it has 4 LAN ports, no USB port) and i want to connect my USB printer HP Laserjet Pro P1106 to the network. Want to know if that is possible?
View 1 Replies View RelatedI'm trying to get a DS lite connected to my university's wifi, which I learned doesn't broadcast a Wireless-b signal, which a DS needs to connect. Can I setup a my own router connected to an ethernet port, configure it to boardcast wireless-b and get on wifi through that? I asked another forum which said yes, but I want to make sure before I buy anything.
View 1 Replies View RelatedI have a cabled network printer, Xerox Phaser 6125n, that have always worked properly from my 3 desktop computers and my laptop.A few days ago, my old dlink router went dead, and I replaced it with the TP-Link WDR4300 router. Everything worked as usual afterwards, until I found out I could no longer print on my printer. I can access the printers web interface through the ip adress, change settings and such through the browser, but the printer has offline status in windows and print jobs never leaves the print queue in windows. I tried deleting the printer in windows (tried both windows 7 and 8) to reinstall it.
View 7 Replies View RelatedI need the router's name and can't find it. I've tried every combination I can think of and still no luck. I thought it it might be the SSID but no.
View 1 Replies View Related I used WPS on my DIR-655 Rev B1 FW 2.03NA to register a Brother HL-2270DW Wifi laser printer and my Mac can never wake it up to print. It always works fine from all my Windows machines.It appears as xxx.xxx.xxx.6 on my network. But the router only shows its IP as 0.0.0.0 on the STATUSWireless page and I can't find any way to change that. My assumption is that the Mac can't find it because of this, but I'm not an expert on WPS.Maybe I should take it out of WPS and just assign it a fixed IP using DHCP Reservation. Or is there another fix? I haven't ruled out the Brother OS X printer driver, but it and the printer's firmware are both up to date.Two odd things:
1. I can ping the printer from my PCs but the Mac can't find see in and it's not a Firewall issue.
2. I can see the brother printer in Finder's Shared devices: so it sees it but refuses to interact.
How to install single port D-link wifi router through Modem "Single Port Wifi Router"
View 1 Replies View RelatedI have a 4-port Zyxel P334U with WLAN, and I would want to set it up so that besides normal WAN, each connected computer also has access to the other local computers. I've tried setting it up before, but haven't managed to get it working, so I gave up.I have DHCP set up, beginning at 192.168.1.16. WAN and ISP DHCP works, so each computer has a local IP (192.168.1.x) and a remote IP given by the ISP.
View 6 Replies View RelatedI'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies View RelatedI can't find my WEP key to set up my wireless printer.
View 1 Replies View RelatedI just setup my homelab today, after having Cat5e installed so I can run my servers and network equiptment over wired network as well as setting up a wireless system. I got everything setup and its going great I can access everything from my office now including a E4200 Linksys router that I setup to do RiP (was only choice pretty much, or NAT), and my 891 Cisco Router which is my internet connection.
I use to have the linksys setup to do port forwarding but now I need to figure out how to do it on the cisco 891 router via command line.
Below is my current configuration. I need to be able to access my server which is behind my router by Remote Desktop. I also have a web server, and the kids also play minecraft, and have a server setup so I need to be able to forward their port as well.
[URL]
Ths is from the link above, would I just do like that but then put in my IPs and is that my Private IP I use this or my public facing. Also he has "interface Dialer1 6881" again after the port in the second and third row. I dont really understand what they have there. I understand basic access list and such though I am extremely rusty.
!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.0.0.2 6881 interface Dialer1 6881
[Code].....
Trying to setup port forwarding for an XBox 360. Set fixed IP on XBox using IP outside DHCP range. DHCP range is .50 to .80. Set XBox to .49. Gateway is .1. Mask is 255.255.255.0.Added four port forwarding rules per directions on xbox site and also portforwarding.com for ports 53, 80, 88, 1074 to the static IP Turned off DMZ, Turned off UPnP, Turned off SPI. Windows firewall is on, running XP Pro SP3 and Win 7 Pro on other devices.Making the rules active for the fixed IP shuts off internet access for other devices.Single router (E4200 V2), switch, then remaining devices. Private IP addresses in the 192.168.xxx.xxx range. Rebooted router, same issue. What am I missing?
View 9 Replies View RelatedI have a network printer which is connected to unmanaged switch, then unmanaged switch is then connected to one of the slots on the router (to get internet access). I use the program Free IP Scanner to look for the IP so then I can find the IP address of my printer. Then I would go to Port setting of the printer and change. Every week or month I have to do this. Two things I would like to know:
1. I have a 2003 server which is not connected or active yet. it's just sitting there running but no computers or printers are connected yet. How do I make this to be a printer server and solved my issue of having keep tracing the IP for my printer?
2. If not using the server, how would I setup my printer IP address to be permanent?
using t-mobile dongle on laptop to get internet but hp printer wont see provider in setup.
View 1 Replies View RelatedI'm trying to setup my HP wireless printer and it is asking for WEP Key and I haven't a clue. This is a home computer. I have a U-verse router.
View 2 Replies View RelatedHow do i setup a network printer on server 2003 .
View 1 Replies View RelatedI just bought a WRT54GL which is working perfectly. I needed it to extend my home network for my kids (I have not a very fast internet connection and my kids are eating all of it... With the WRT54GL I can choose how much they can have. So my own network has a netgear modem and a netgear wifi access point which is in this network : 192.168.0.x.
This network is not blocked in any way (just password protected). For my kids network, the WRT54GL gives addresses in this network : 192.168.1.x and is limited in speed. Everything is perfect, I have internet connection on both of my network, There is just the problem that I cannot access my printers, my servers, my computers.... that are on the 192.168.0.x network from 192.168.1.x. Is there a solution ? I already tried to force the WRT54GL to go to 192.168.0.x network but no more connection. Should I "bridge" the two networks ? How can I do it ?