Can a dir-815 be setup as a repeater?? I have a Linksys wrt54g as the main router can the dir-815 be used to extend the wifi range of the Linksys router. If the dir-815 can be setup as a repeater how would I go about setting it up as a repeater?
View 3 Repliesfacing issues with TP-Link TL-WA801ND while setting it up as a Universal repeater.The AP is a Linksys E3200..and I got the TP-Link to broaden my WiFi at home, I was successful in setting it up, however, after a day or two I get prompted to enter a "WPA2 Enterprise" username/password.I DID NOT setup WPA2 Enterprise, mine is WPA2 Personal...it's peculiar that it works for a bit then reverts to Enterprise.
View -1 Replies View RelatedI recently purchased a Linksys E1200 to replace my Linksys WRT54G. I'd like to utilize the WRT54G as a repeater. Is this possible, or do I need to buy a "repeater"? how to configure/set up the WRT54G repeater?
View 3 Replies View RelatedI have a linksys wrt54g v2 router I want to convert to a repeater. I looked up instructions buteveryone says after all is done I have to connect my main router to the new configured rrepeater. Is there.a way I can do this without connectingthem together via cable. My house is seperate from the main house and running cable is not logical I have signal at my house just need better signal
View 1 Replies View RelatedActually i´m working in a departamet of networking in my business with only cisco devices. I used to work with the wap200 wireless-G Acceess point (Small bussiness), but now i have a problem with it. I´m trying set the wap 200 as a wireless repeater for WRT54G but it´s a impossible.
View 1 Replies View Relatedis it any possibility to set my router WRT54G V2.2 as a wireless repeater? and does any manual for this exist?
View 3 Replies View RelatedI am using a PPPoE connection using a linksys WRT54G router (working perfectly) and am now trying to set up an Edimax EW-7206APg to extend my wireless connection range. I followed the instructions given on the Edimax manual, and while my devices (iPad, laptop) got connected to the new repeater network, I could not access the Internet from it. I may be wrong, but the instructions on the Edimax manual seemed to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connection?My router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest.
View 6 Replies View RelatedIs it possible to configure the WRT54G as a repeater signal of the WRT120N?
View 1 Replies View RelatedExtending wireless network range with a repeater HP and Netgear - YouTube my reapter is a old netgear router n150 wondering if its possible.
View 4 Replies View RelatedTrying to setup a repeater down stairs for better wifi signal but am running into a problem. The main router I use for my network is a Linksys WRT54GL. The router I'm trying to hook up as a repeater is a Asus RT-N10+. The issue I'm running into is that they both use the same IP address for the web gui so when I try to configure the Asus it goes straight to my Linksys instead.
I tried to disconnect the Linksys in order to get the Asus going in repeater mode but didn't work. What I'm wanting to do is change the router IP address on the Asus so I can have both of them online at the same time to get the Asus going as a repeater. I tried to change the Asus IP but when I did it asked me something along the lines of whether I wanted to change the DHCP address being it didn't match what I had typed in as the router IP.
How to setup dir615 with wpn824v3 as a repeater? I run Windows XP Home on 3 pc's
View 4 Replies View Relatedhow do you setup a wireless repeater using a awus036h. Or is it even a option?
View 1 Replies View RelatedI have a wireless access point/modem at one end of my property (which I cannot relocate). To improve wireless connectivity on the other end of the property I am thinking of placing a wifi repeater (probably a cheap one like http:[URL]... mid-point in the property. However I don't quite understand how these things work. I assume repeaters, extenders, boosters are all the same thing?
Does the repeater actually create a new seperate wifi network, so I will effectively have two wifi networks/SSIDs? or will my wireless devices still see only one wifi network? If it creates two wifi networks what happens when I move through the property with say a laptop, will the laptop need to disconnect from one and reconnect to the other hence interrupting the connection? (which is not ideal).
Also does the repeater take up an IP from my main wireless access point/modem? My setup uses a block of static IPs and hence I would prefer not to waste an IP on the repeater if possible.Homeplugs is something else I'm looking into but that seems to be a more expensive option. With Homeplugs I would disable the wireless on the main access point/modem. Then use the Homeplug to put a wireless access point in the centre of my property hence giving fuller coverage.I've also tried higher DBi antennas (& directional ones) but they have not been effective.
So i am trying to Set up a wireless repeater so i can have a better signal in my back yard but i could not set the configurations for my repeater because the gateway (ip address? Not really sure what it is called) would not work when i entered it into the browser. So i went into command prompt to make sure i had the right gateway and it did not even exist.
View 6 Replies View RelatedI have a Cisco WAP200 Wireless-G Access Point - PoE/Rangebooster with the latest firmware 2.0.2.4-ETSI?I’m trying to set it up as a repeater, repeating the wireless signal from a Cisco 877W.I have configured the WAP200 with the same SSID, WPA key, and channel as the 877W.
I have changed the WAP200’s AP Mode setting to Repeater, and picked up the 877W’s MAC Address.The WAP200 is broadcasting and I can connect to the wireless network, but I don’t get DHCP. It’s almost like it’s still in Access Point mode.
I have a existing WiFi ADSL router and I have a WAG120N lying spare in my closet. I recently shifted to my room a floor above. I wanted to amplify signals as the current router is not able to beam signals that far. Hence I wanted to set this up as a WiFi repeater to have a complete coverage. I tried N number of ways but could not succeed.
View 1 Replies View RelatedI use my e2000 as router and want to use the e4200 as repeater. so if i connect wireless to my e4200 i can see all my devices also the one on the e2000. How to setup the e42000 ?
View 5 Replies View RelatedI have 3 WAP200 wireless-G access points. I have one set up as an AP the other two are set up as repeaters to the main AP.
My question is Do I need a lan connection to each repeater ?
also, do I need to create SSIDs for all three? & if so, do they need to be the same?
Can the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.
View 11 Replies View RelatedI tried to set up Tenda W311R as a repeater to increase the coverage. I have done the following, but still it cannot get Internet access:Set up WDS with the same channel and use the same encryption as the Linksys router; Disable the DHCP in the W311R;From the wireless point of view, I can see the Tenda router, but no Internet access.
View 3 Replies View RelatedI have WRT54GL and want to setup wap54g as wireless repeater? I need to expand the signal using wap54g
View 1 Replies View RelatedI have a D-Link DI-624 router and I understand that I can convert this router to a repeater using on line software thus allowing me to extend a wireless signal from up to a 1/4 mile away
View 1 Replies View RelatedI was wondering if it possible to use the DIR-825 as a repeater. My main router is a Airport Extreme but it doesn't reach the whole house. Now what I'm also wondering if I can use the repeater as well as a SharePort for my external hard drive while it is being used as a Repeater.
View 4 Replies View RelatedI have a WRT54G wireless router that I haven't used in years because my old cable provider supplied me with a router. I recently switched cable providers & they don't provide a wireless routers. I would like to use my WRT54G router, but I don't have the cd. I figured it wasn't a problem because I can just do a manual setup using the ip address 192.168.1.1. I receive the pop up window to enter the user name & password. I follow the instructions & just type in the password field the word admin & l left the user name blank but it doesn't work.
View 4 Replies View RelatedI just recently upgraded my home router from a 615 to a 655, so I thought I would use the old router as a repeater bridge at another location.
I read that the DD-WRT firmware offered a repeater bridge function, so I successfully flashed the 615 C1 with the latest release 7/12.
I get all of the configuration steps, and even have set up client bridge mode. My problem is when I bring down the list of available wireless modes, repeater bridge isn't on the list.
Is the C1 version not able to do this? is there something else I need to do to enable a repeater bridge?
I had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:
Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.
I find that within my apt I can only get about 32% signal from my shaw Wi-Fi router. They don't support what I want to do.. adding my d-link router to boost or repeat the signal.
View 1 Replies View RelatedHow do you convert a D-Link router into a repeater?
View 1 Replies View RelatedI want to extend the range of the wireless network using a 601 (or just a relatively lowend N series). Can I just set a 601 as a repeater? Not seeing anything in the manual that provides instructions. I don't have the ability to cable the routers together. I want to do it all wirelessly if possible.
View 1 Replies View RelatedMy D-Link DIR-628 is at the far end of my house (next to my desktop and cable modem) and my PS3 and laptop are at the other end of the house in my living room. I'm not sure what's in my walls but it is NOT WiFi friendly!
[code]....
So I was thinking about buying a cheap N router and flashing it with DD-WRT and putting it in the living room.
I'd like this 2nd router to:
(a) Plug into the PS3 thereby "upgrading" it's crappy wireless card to something faster
(b) Have it act as a WiFi repeater to boost coverage on the far side of the house.
So is this going to work the way I'm describing it here? That's my current understanding based on what I've read, but I want to make sure I'm not missing something before I order the hardware.
I have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.
View 2 Replies View RelatedI'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies View RelatedHow to setup WRT54G in router mode
View 9 Replies View Related