I recently downloaded DDWRT to my DIR-615. I was trying to change my DIR-615 from a router to a client bridge but I was not able to get any internet connection on the device after I change the settings.
View 1 RepliesI recently discovered the dd-wrt world and am attempting to make a wireless adapter for my Xbox360 using a D-Link DIR615 rev C1 router I purchased and linking it to my home wireless network router (also a D-Link DIR615 but rev B2). I successfully loaded the dd-wrt firmware onto the C1 router and have attempted (multiple times) to set it up for use with my 360 following the instructions posted here at the dd-wrt wiki posting. However, after following the instructions to the letter I have been unsuccessful. After setting it up I can get the router (connected via ethernet to my laptop) to "connect" but it lists the connection as connected to a "unidentified network" with no network access.
View 12 Replies View RelatedI've recently purchased a Buffalo WHR-HP-GN flashed with the latest version of DD-WRT with plans involving its use as a client bridge and I have had nothing but problems trying to get this thing connected to my wireless network in client bridge mode. The closest I've gotten to getting this thing connected to my network is by setting the Buffalo to 'G-Only' mode and setting the security to 'WPA2-Mixed' with 'TKIP-only' for the encryption, however I can only ping the D-link via my notebook and the DD-WRT web interface; no other devices nor the router can ping the laptop or the WHR (Neither of them are listed in the 'connected clients' page on the D-link's web interface). The Buffalo works brilliantly when pairing it with an old WRT54G that I've dug out of the closet and a friend's WZR-HP-300NH.
With the WHR-HP-GN, so far I have:
1. Flashed the Buffalo 'Professional' (really DD-WRT with their own branding) firmware to the latest DD-WRT release compatible with the router.
2. Flashed the firmware to the second newest release of DD-WRT.
3. Flashed the firmware back to stock, then to Buffalo's alpha release of their 'Professional' firmware, then to their 'User-Friendly' (read: proprietary) firmware.
4. Flashed the firmware back to the latest DD-WRT version.
5. Set the wireless properties to 'G-only', encryption to WPA2/WPA-PSK TKIP (the closest I've been to connecting this bridge to the network, though no other device including the DIR-655 can see the bridge or the laptop it's connected to).
6. Same as #5 except tweaking with different combinations of wireless modes, channel widths, and security + encryption schemes (WPA only, WPA2 only, TKIP or AES, no security).
With the DIR-655, so far I've tried
1. Power cycling it.
2. Flashing the firmware from 1.21 to the latest (I think 1.35NA).
3. Falling back to 'G-only' mode with various encryption schemes (including none).
4. Set it to 'N-only' with various encryption schemes.
5. Meddled with different channels and channel widths.
That's about it. I really don't think there's anything wrong with the WHR as it works great with different routers/APs. Maybe I've just experienced my first caveat with owning a router that was manufactured two years before 802.11n was ratified as a standard?
I have a WRT54G2 V1 linksys wireless router. I was going to upgrade it to DD-WRT and install it at my mother's house. It was working before upgrading it to dd-wrt. I followed the directions located at:Linksys WRT54G2 v1.0 - DD-WRT WikiAfter following the directions and doing a hard reboot I was able to log into the router but was unable to connect to the internet via WiFi and/or Ethernet.My internet enabled TV and wireless labtop detected the ssid made by the router but could not connect to the internet. I am able to connect to the internet using a old Netgear WGR614 v6 router.
View 7 Replies View RelatedI am not able to share files with computers past my Client Bridge. I can see one computer past the bridge in my network and two more can see but all have internet, but still can not access ant to get to their shared folders. Do not know if operating systems would made a difference, I main computer run Windows 7 Pro 64 bit. all the rest run XP Home. Have two computers before the bridge no problem there.
View 2 Replies View RelatedI wonder if dir825 with ddwrt firmware are able to set up additional tftp server? I try to serve dir825 both as tftp server and dhcp server to allow remote client to have pxe booting from it. ( the booting image file would be located in external HD attatched to dir825's usb port )
View 1 Replies View Relatedif there is a stable or if the current website offered version of DDWRT is stable and working good on Asus Rt-N66U router?
I really want to work with some of the features like VLAN etc... on this firmware. I am no stranger to the software but I want to be sure I am not going to burn up my router or cause it to frag due to incomplete software
I have replaced my main router WRT300N running dd-wrt with the a stock E4200 and an old WRT54G aslo running dd-wrt configured for wireless client bridge. Now that I'm learning more about 802.11N, I was wondering what client can I use to achieve 5ghz simultaneously radio transmission since my current setup cannot do this in the 5ghz band. Can the E3000 be ran in wireless client bridge mode, if not what product can provide this? On the other thought am I understanding MIMO?
Old setup: 802.11G 2.4ghz
WRT54G ))) ((( WRT300N ->ISP
Current Setup: 802.11N 2.4ghz MIMO?
WRT300N ))) ((( E4200 ->ISP
Wanted Setup: 802.11N 5ghz MIMO
( E4200 ->ISP)
Region : Poland
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I have some linksys router that I used as wireless client bridge. I have main router that is connected to Internet and linksys router which is connected to main router's WiFi. Linksys router acts as client bridge connecting LAN devices to main router. Now I own TL-WDR3600 and I would like to replace linksys router. How can I achieve the same on TP-Link router? I don't see any option for setting wireless operation mode.
We have dlink dir320 router and cisco 877W.
The goal is to make a 877W to work as a wireless client of dlink dir320 and brigde the LAN&WLAN so than the LAN clients of 877W could take DHCP from Dlink 320 directly.
Here's the config of 877w:
!
bridge irb
!
dot11 ssid DLINK_SSID
[Code].....
What kind of hardware are people using for mobile bridges? I have not had good luck with Cisco 1242's in bridge mode with mobile-client enabled. The only reason we're using the Cisco access point over standard industrial bridges is because we need to manually forward the mac addresses of the devices behind the bridge. These are being installed on robotic forklifts. They have a generic ethernet scrolling marquee installed that does not maintain any active connections and drops from the fowarding table in the bridge if not staticly configured. I'm looking for an alternative because the roaming is not nearly as smooth as it should be.
View 3 Replies View RelatedI just have an old Dlink DIR-615 Wireless router. I have some problems with it and need to improve it... So, what is the best option... buy a new DIR-636L or 657 router or install the latest ddwrt firmware on the existing one?
View 3 Replies View Relatedhow to change a clinet as server for all the remaining clients in a local area network
View 3 Replies View RelatedI have a 2900 ISR that my VPN clients connect to using IPSEC over UDP. I am having periodic problems, especially with clients connecting through DSL, where they connect and immediately drop. Sometimes this is resolved by users updating their home router firmware. I'd like to issue a new client PCF file using IPSEC over TCP to see if that resolves the problems.
Can I have both running at once, and what do I need to add to the 2900 to enable this connectivty without breaking the existing clients? If the test is successful, I will migrate all users to the new configuration. This ISR is also used to support L2L connectivity for a handful of sites.
Who knows the best version (DD-WRT or other) to repeat the wireless signal with a E3000?At worst, a client bridge mode could be sufficient for my needs...
View 9 Replies View Relatedhow to change a windows 2003 server name through client
View 1 Replies View RelatedWe are using a CISCO1921-SEC (ISR) with IOS 15.1 and we configured a "crypto isakmp client configuration group". We can connect with the "Cisco System VPN Client Version 5.0.07.0410" via IPSec/UDP.
1. Is it possible to push routing informations to the System running the VPN Client ? A the moment all traffic is routed to the tunnel but we like only one route to the network permitted with "pool ..." in the "crypto isakmp client configuration group NAME" section.
2. We searched for changing from upd connection to tcp connection via special port. Is it possible with IOS 15.1 on the CISCO1921-SEC ? Is there something possible like "iskamp ipsec-over-tcp port 10000" ?
For access by external users on our network use all Cisco VPN Client, we have a VPN3000 Concentrator and a Cisco ACS 2.6 for authentication.We wanted to upgrade to the latest release of ACS 4, x .... you can set a password expiration for VPN Client? Or make sure that the remote user can change password?
View 2 Replies View RelatedI have a curious issue on a customer site where the above components are installed.The issue being that the iPhones the users utilise cannot connect to the mail server via WiFi, they are forced to connect with their 3G connection. The core issue seems to be the 887VA, as when I've installed 'lesser' branded ADSL routers, the connection seems to be fine.The iPhones are set to access the mail server via the URL: mail.customer.com. Should I change this to the internal IP of the server 192.168.12.200, the mail connection works fine. However I cannot expect the client to make this change every time they arrive or leave the office. Presently I have them disable WiFi when on premises.
View 1 Replies View RelatedWe are using an ASA 5520, running 8.4(3). We have users running the AnyConnect Secure Mobility Client 3.1.02026. I have the AnyConnect connection profile configured to authenticate users using LDAP over SSL. I enabled the password management and am able to get password change prompts to appear in the AnyConnect client. However, new passwords are rejected and changing passwords through that prompt does not work. I'm not sure what the cause of the problem is, since LDAP over SSL is enabled and working, which is required for the password management feature
View 9 Replies View RelatedIs there a way to change the timeout for the Client Excluded: MACAddress status? It seems like the exclusion is rather short. I'd like to have the ability to control the exclusion time. Using WLC-5508 7.0.116.0.
View 2 Replies View RelatedI'm trying to change the DHCP Client Lease Time from 1440 minutes to 480 minutes. When I try to apply the new settings, I'm getting a message that says "Invalid Characters" and it won't stick. I've tried this in three different up-to-date browsers (ie10, Chrome and Firefox). Also, I'm connecting locally through LAN and I have the latest EA6500 Firmware: 2.1.39.145204
View 2 Replies View RelatedI need an AP that can run in client bridge mode. By that I mean a device that can be connected to a PC via the ethernet cable and provide wireless access because these older devices don't have wireless network cards?I looked at the WAP321 but it just uses a wizard. I need a device with IOS so that the PSK keys can be encrypted when viewing. I need to have the config backed up and the PSK can't be in clear text.
View 5 Replies View RelatedI have a crappy router/modem from comcast with two windows machines and a linux web server connected. I also have another router, a Linksys WRT54G with DDWRT firmware with WAN connected to the modem/router. The linux web server has a static IP, configured with /etc/network/interfaces The network goes down randomly. Disconnecting and rebooting the linux web server usually fixes it. It's possible that the WRT54G could be at fault as well.The problem is that I just don't have any information on what is happening on the network. (Well even if I had the information, I'm not sure I would know what to do with it) I installed wireshark, I figure I should just leave it running until the network goes down, then I can go through the packets and see if I see anything weird?
View 4 Replies View RelatedDo the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
i have a question about tunneling a software EasyVPN client to a client ASA Network. It looks like this:
EasyVPN Server 192.168.202.0/24 Network extension mode to Client EasyVPN ASA 192.168.1.0/24 This works fine in both directions. But now i want to connect the client ASA network via EasyVPN software client from outside. The user are already able to connect to the ASA Server on its static outside IP obtaining an IP from a 192.168.21.0/24 pool. This works fine. But how am i able to connect to the 192.168.1.0/24 network from this client?
how to make the java SSH thin client applet bigger in SSL VPN Clientless portal?It works and all that but the window is literally half the size of the monitor and unworkable. You can't even hit tab! (tab moves focus around the browser...)I am using the latest java applet (Oct 2012) and ASA OS 8.4(5)
View 3 Replies View RelatedCan I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedI have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
View 4 Replies View RelatedTelus cell phone usb connection and a Lan ethernet connection, was trying to use windows 7 to bridge the two networks.
View 6 Replies View RelatedI have a new internet connection. It is displaying lights for DSL, PWR, INET, WLAN.I can connect but it always reads the message "No Internet Access"I went to the service provider to get this fixed. And they created bridge mode through LAN so I could connect using a username and password. (create a new connection > broadband ). But I innocently pressed reset button. I don't want to go back to the service provider to setup the bridge mode or ability to connect by a username/password through LAN.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Ultimate, Service Pack 1, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU T5750 @ 2.00GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 3070 Mb
Graphics Card: NVIDIA GeForce 8400M GS, 256 Mb
Hard Drives: C: Total - 125633 MB, Free - 9275 MB; D: Total - 102547 MB, Free - 30795 MB; E: Total - 10291 MB, Free - 2701 MB;
Motherboard: Quanta, 30D2
Antivirus: Microsoft Security Essentials, Updated and Enabled
So I have an RV120W as my "main router" but I can't get a wire into the garage to get a couple of computers in there access to the internet / LAN. I have a WCG200 cable gateway at my disposal, with a built in 4port switch and wondered if I can configure it's WLAN to connecto the RV120W SSID and use wireless as my link between my garage network and the rest of the house LAN? WCG200 isn't going to connect at blinding speeds, which I'm ok with, I just wanted to know if it's possible?
View 3 Replies View Relatedif I want to bridge between 2 VLANs ,can I use IRB like I would use in a router for bridging to ethernet interfaces for example?
Config example:
bridge irb
interface vlan 10
ip address 192.168.10.1 255.255.255.0
bridge-group 1
[code].....