i share a wifi connexion with some friends and i'm using a comtrend CT-5361T router.i want to configure my router to limit bandwidth of each other but i don't know where to start.for example, i want to give to my first friend a max of xx ko/s of bandwidth, for the second a max of yy ko/s of bandwidth, ...
View 1 RepliesMy Comtrend WAP5813n router, seems to be failing at port forwarding as I have configured it to forward ports,all the port checkers (offline and online) say those ports are open, yet I cannot access through them,it just fails to forward them(My server isn't blocking anything because it has worked on a previous router).
View 19 Replies View RelatedIs it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies View RelatedHow to configure a router so that i can ping it while there is another router in between
View 1 Replies View RelatedI have a Sky [Sagem] F@ST2504N Wireless Router and Sky is my ISP. I have been using powerline adapters to extend my network into a room upstairs that is a WIFI deadzone. I would like to use a router to turn this into a wireless signal in the upstairs room. i.e. Primary (SKY) Router -> power line in -> powerline out (Upstairs in deadzone) -> Secondary (TP-Link) Router..I have got a TP-Link 150mbps wireless N ADSL2+ Modem Router (Model No.: TD-W8951ND) .I am plugging this in and configuring it from factory settings via the web setup. How to configure the new router?
View 4 Replies View RelatedI have bought D-615 wireless router, I have Cable modem, am trying to configure however unable to do it?
View 1 Replies View RelatedHow to configure dwl-2100ap router
View 1 Replies View Relatedgot the DIR-655 for gaming not knowing about LAN and WAN can any tell me if i can config this router to work properly with my broadband i have ONT that the router connects to
View 1 Replies View Relatedi have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
View 3 Replies View RelatedHere is my Desktop Specs:
Windows XP Svc Pack 3
Mainboard :Asus P5KPL-CM
Network Card :Atheros AR8121/AR8113 PCI-E Ethernet Controller
Current Router - LinkSys BEFSR41 (Hardwired, CATV cable)
Static IP - 192.168.1.100, 255.255.255.0, Gateway 192.168.1.1
Problem: I purchased a new GB router, Dlink DIR825, wireless and 4 ports, and cannot connect to it to set it up. I need to get into it to change its IP address from 192.168.0.1 to 192.168.1.1 and to make a few other changes. I have 6 different ethernet cables, all of which work with my desktop as well as my laptop. I can get into the new Dlink router just fine with my laptop so it is not a bad port on the new Dlink. The cables work with my existing router and my new router using my laptop so it isn't a cable problem.My internet connection is Hughesnet (DISH) which uses the 192.168.0.1 address, the same as the new router. So here is what I have tried:
1. Powered down Hughes router, new router, and old router.
2. Removed cable from Hughes router to old Linksys.
3. Changed static IP on desktop from 192.168.1.100 to 192.168.0.50 and Gateway to 192.168.0.1.
4. Rebooted
5. Connected ethernet cable from desktop to Port 1 on new router.
6. Powered up new router.
7. Brought up Browser and entered the 192.168.0.1. Nothing happens. The Port light on the new switch shows the connection properly and the other lights are on properly, except for the Internet light which I haven't hooked up yet.
The above does not work so I powered down everything and then:
1. Connected the cable from the Hughes internet modem to the Internet port on the new modem.
2. Powered up Hughes modem and waited for all lights to come on.
3. Then powered up new router and waited for all lights to come on. This time the Internet light came on like it should.
4. Powered up my desktop.
5. Brought up Browser and entered the 192.168.0.1. Nothing happens. I expected this since there would be a conflict with the 2 modems having same IP.
Next I tried to basically set my desktop to use DHCP and removed the cable from the Hughes modem to the new router. Powered down everything then brought them up one at a time, Hughes modem, router, and PC. Still not able to connect to the new router.I also used my laptop to set the new router to 192.168.1.1 and reset my static IP to the original 192.168.1.100, 255.255.255.0, Gateway 192.168.1.1. Still nothing and I couldn't even ping the router.
Right now I have it connected like this: Internet-> SURFboard SB6120 Modem -> DGL-4100 Router (modem in the WAN port, 3 internet connections plus the switch in the LAN ports) -> DGS-1008G Switch (2 other internet connections connected to this, as well as an Xbox 360).The problem is that everything connecting to the router works, and nothing works on the switch even though the power light is on (however, the port on the router that is receiving the switch is not lit up). I'm guessing this is because the router only assigns as many IP addresses as it has ports or something.
View 10 Replies View RelatedI am researching routers for a large emnterprise application, and their useability as firewalls. Also, is their one that is considered to be better over another?
View 3 Replies View RelatedI'm active duty military, currently overseas.I have a wireless connection and recently purchased a Samsung HT-E5500 home theater system. I'd like to be able to stream Netflix but understand that I need a VPN with a US ip address to get it to work. Any VPN service I can use, and how to configure it with a Linksys E3000 router, so that I can use it with both my computer and when connected to the Samsung system?
View 1 Replies View RelatedMy boss want me to configure a cisco router 1800 series to an IP VPN, but I don't know how to configure a router with an IP VPN...
View 2 Replies View RelatedCan't get into my netgear router to config it. I have tried using 192.168.0.1 and 192.168.1.1. So far it will not give me a window to log in. It has allways work before on xp pro, but now i am using win 7 on my new computer.
p.s. the router is a Netgear model # WGR614
How to configure to use Router with Lease Line ?
1.connect a computer to the wan port-router
2.give the ip in the url-------- 192.168.1.1( by default )
3.enter username and passwrd
4. then in the GUI mode
5. go to the wan setting ...router
6.there put the live ip and the gateway and the dns....aircel detail....
7.go the lan setting and put the lan ip series do nt configure dhcp go manually to all the nodes and put the lan ip u have 4 lan ports
8.out of 4 port ...port 1-- connect the dialler...in lan port
9.and in port 2 connect to (switch) a unmanaged switch frm where u can connect to your lan
10.if in the lan setting u hv given the ip 192.168.1.1
11.then put ur dialler ip 192.168.1.2
12. and local lan machine will tk the ip frm 3 onwards
13.nw if u want to authenticate ur dialer in our voip gateway then give the ip of ur router
15. 192.168.0.1 will be the ip of the lan setting in the router
16. and this will act as a gater to ur local machine gateway
I have a Netgear WNR1000v3 router that I just reset to factory defaults, and now when I run ipconfig /all it doesn't show up as having a gateway. Note that I am connecting with a laptop wired in to a LAN port on the router. (also tried on WAN port) Here is what shows up:
SpoilerEthernet adapter Local Area Connection:
i want 192.168.0.1 with mask 255.255.255.0 class network to communicate with 10.7.27.1 with 255.255.255.128 mask to have the same gateway
View 2 Replies View RelatedI'm having trouble configuring my pace 4111n router from att. I need to set up my cameras for external viewing and I'm stuck.
View 2 Replies View Relatedhow i can configure dlink dl624
View 1 Replies View Relatedi received a public ip from my ISP and need to configure to enable access my server remotely
View 1 Replies View RelatedMy ISP provides me internet connection through password protecting Access Point bearing IP address 192.168.20.1 built with IP filtering which allows only a particular IP 192.168.20.88. I am not able to access internet on more than one computers simultaneously because router allows only single IP and I am not sure what are the WAN IP's uses Access Point provided by ISP eg. IP, Gateway and DNS. My ISP provides me static IP address for home computer as mentioned below :
IP : 192.168.20.88
Gateway : 192.19.20.1
DNS: 192.168.20.1
Alt DNS : 192.168.20.1
My public IP address is 180.87.210.26.
Is there any option to add a router to bride or configure router as proxy server so that i can access internet more than one PC's simultaneously.
I am using D link Wireless router and the Model is DI-524 I am unable to configure the router with static Ip as the ISp having Static Address.
View 4 Replies View RelatedI want to know how to configure a wireless network using an wireless router???
View 1 Replies View RelatedI have belkin n750 router. I cannot get the guest network to connect to internet. The Main one connects to internet. How can I solve this problem?
View 1 Replies View RelatedI had a Airtel connection with me for which i was provided Beetel 450 BXI ADSL2 + Router to connect to net using wi-fi on my laptop.How ever now i have changed my isp to ortel cable net providers.i access net on my laptop using lan cable connected from cable modem to my laptophow to configure Beetel 450 BXI ADSL2 + Router so that i connect my cable modem to Beetel 450 BXI ADSL2 + Router and access net wi-fi on my laptop. my os is vista.
View 1 Replies View Relatedhow to config wrv 210 wireless-G vpn router config.
View 0 Replies View RelatedI have a question, it is possible to have two WAN interfaces to configure a cisco 892 router with an ip 255.255.240.0 84.197.167.111 adderess of the first interface and a different ip address 84.197.174.182 255.255.240.0 on the second interface
View 5 Replies View Relatedhow I configure netflow on a cisco 877 router.
I have an interface e0/4 that is 172.1.1.1 on router one (network one) which links to another router (onnetwork two) which has an interface of e0/4 172.1.1.2 which allows two networks to communicate. Network one is 192.168.0.0 /24 and network two is 10.255.255.0 /24.
How do i configure netflow to monitor the traffic going through these interfaces?
I want to configure PAT on the router I have no configuration yet
View 1 Replies View RelatedHow do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies View Relatedsetup a vpn server cisco.
device cisco router 1841 [URL]
i am having trouble in configuring my cisco router 887. my connection type from my ISP is static ip. im not sure if i have entered the correct command in the CLI.
router(config)# interface fa 0/0
router(config-if)# ip address 61.10.XX.XX x.x.x.x
what would be the command to do this?and also, i want my other PCs to receive DHCP ip address from the router.