Is it possible to transmit Audio and Video wirelessly with UPNP. Let say I would like to watch youtube videos or any movies that is streaming live on my PC in my room on my TV (with UPNP).
View 1 RepliesActually i need a streaming server that supports both audio(mp3) and video formats(mp4,avi..).But it should work in multicast and should possible to stream with VLC media player.now i'm trying helix media server.In this what are the procedures to configure helix sever in multicast.and how to stream media from it.Or Any other streaming server is there that suits for my need.
View 1 Replies View RelatedI need to transfer live video and if possible video from station A to station B over wireless network. So what are the hardware requirements and setup cost...
Secondly how should i connect my CCTv cameras atleast 5 to computer's webcam so that i can transfer video over internet.
I have the WAP4410n connected to a SLM2008. I tried to change to 100Mb the port in the switch but then I lost the connectivity.
But it's a giga port and it must work as a giga port. The new firmware must resolve the problem, and not to be a work around. Or what will be the next, not to use N, only G, or only 20MHz or...
I need the WAP4410n for streaming audio and video?
When I view my DCS-932L camera in the Main Console of DViewCam, I can here the sounds in the room being viewed. But if I record the video and play it back, there is no audio on the playback. I have the microphone on the camera enableI now have sound recording, however, the audio is about 3 seconds behind the video. Is there a setting somewhere to keep them synchronized? I have checked all the video sync checkboxes I can find.
View 4 Replies View RelatedI have been having a problem with my 4400n dropping connection when streaming video / audio.It is connected half duplex to a cat2950 and the media server is mediatomb on a linux box the client is a ps3 presently.
View 3 Replies View RelatedHow do I setup this on the SRP527W? I already block most of the video stuff on the internet. But I want to make this one more step.
View 1 Replies View RelatedI posted this on a previous thread along with another question, but since I marked that as answered I'll post it here so people will see it.Is there any way I can use UPnP WITHOUT having to have the videos I want to stream in my WMP library? Windows Media Player has always been a pain for me, from my videos not showing up in the library when I know they're there to not being able to switch audio streams in a video. (If VLC Media Player or iTunes had a UPnP library.
View 3 Replies View RelatedModel : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Cable TV provider
It seems there is a bug with TL-WDR3600. As it can be seen in the following image, the UPnP is off:But my firewall on the computer is reporting flood of packets originating from the router (it's the routers MAC address and IP address):I don't know what ETH type packet is, 0026 might be hex (38 decimal as seen in the raw log). But port 1900 is definitely UPnP.At the router, the wireless switch is off, as well as all other options for sharing etc. This computer is the only one connected to the router. The router has been reset several times.
I've got an ASUS G50V that I normally connect to the net through a wireless router but I recently bought a router so I can make a physical connection and increase speed. However I cant get it to connect to the router no matter what I do (i had it working for a few hours at one point but it dropped off again).I confirmed it wasnt the router but running a crossover cable from the laptop to my desktop, setting static ips on both. Now I can ping the laptop from my desktop but for some reason I cannot ping the desktop from the lappy. I've tried everything I can think of but no dice.
View 4 Replies View RelatedI recently bought a Nintendo 3DS but unfortunately my University's wireless security (WPA2 Enterprise) is incompatible with the system. As such, I was looking for a way to transmit a wireless signal from my computer, and place an alternative form of security onto it (such as WEP), so that the 3DS can connect to it.
At the moment, my desktop is connected via ethernet cable, which plugs directly into a wall socket. I'm pretty unsure as to what to use, I've heard of things such as 'wireless bridges', but I'm not sure how they work. Also, I'm looking for the device to transmit a signal even if my desktop isn't turned on. Is a router my only option?
i have ipod but i dont have wireless modem i need software thats work from my pc as wireless modem
View 2 Replies View RelatedI have a client(C) and a server(S) nodes plus an intermediate node(I). Each node has a public IP. What I want to do is to transmit some data(whatever) from C to S but this data to go through I. So C ---> S will become C ----> I ----> S. I read something to create a tunnel(ip add tunnel) between C and I and add a route between them ? I tried different examples but did not work at all.
View 2 Replies View RelatedIm curious to know if there is a way, to stream music to my iPad from a drive connected on my network? Either by USB to the router or a hard wired NAS. Im aware of programs like Streamtome but this requires a mini server running on a PC which is want i want to avoid!
I know there are things like the slingbox etc but i cant believe its needed! If you can access the files on a MacBook on the wireless why not an iPad?
I would like to make my audio MP3 stories and audio books available to the visually impaired and others who can no read for any number of reasons. I have already written and recorded the material in MP3 format.I find that virtually everywhere I look I must pay, or the upload limit is so small that a story of any size can not be uploaded. I have an Ipage web site and two blogger blogs where I could post the link for listeners to download the text. I do need to do it all for free, since I am on S.Security.
Stated differently; I want to offer my audio books and audio essays for free from my blogs or website. I can not seem to find who will store my recordings (large enough to actually be a book) for free. The site should be easy to navigate so impaired patrons can use it easily. I did find one, yourlisten.com, but the user has to agree to buy something from their advertisers before they can download my audio text. For the user, then, the service is not free.Does any one know who will store and share my audio text for free?
I work from a computer that can not install any software(locked out), but I want to record good quality audio (at least 192kps) from websites, I've spent along time googling for a website that would record the audio (audio from a different website, i.e. streaming radio, etc.) which I could then download to my USB stick. I just can't find a website that does this, but I think I'm just not using the right search words
View 2 Replies View RelatedNeed drivers for my sensus network notebook with win 98se.
View 1 Replies View RelatedI am able to stream audio from a website when i connect directly to my cable modem but when the router is connected it doesnt work. I have tried resetting the router, ping the website and get "request timed out"The firmware is up to date version 2.25 I have tried other computers that access the same network and they also cant stream the audio.I have also turned off my windows 7 firewall with no luck I can access other sites I visit and stream audio just fine so I wonder if the router may be blocking something on this website?Is there a way to allow an audio stream to come through that may be blocked by the router?
View 1 Replies View RelatedWith firmware 2.06 my DIR-600 had transmit power choices 100%, 50%, 25% and 12,5%.(even 12,5% gave me excellent strength on all my devices, what is really the difference)But after updating to firmware 2.11 (via 2.10, othervise my DIR-600 refused to use 2.11)the choices for transmit power is now only "High", "Medium" and "Low". know the percentage values for those three settings?
View 2 Replies View RelatedIm trying to locate the PDLM for the RTP audio for the 4500 series switch,
System image file is "boot flash:cat4500-entservices-mz.150-2.SG.bin"
Cisco WS-C4507R+E (MPC8245) processor (revision 7) with 524288K bytes of memory.
MPC8245 CPU at 333Mhz, Supervisor IV
Last reset from Power Up
8 Virtual Ethernet interfaces
48 Fast Ethernet interfaces
100 Gigabit Ethernet interfaces
403K bytes of non-volatile configuration memory.
It seems to be an easy task for routers:
[URL]
But not for these 4500's
[URL]
I have a user that uses an ASA 5505 in NEM to have his/her laptop and Cisco IP Phone at home. The ASA 5505 establishes a tunnel to an ASA 5510, which is connected and speaking EIGRP to our core switch. Off of the core switch we have our CCM cluster.
The issue happens on the first call after a long period of no calls. After if happens on the first call, he/she can continue to make calls without the issue. I though it was a timeout issue, but his/her ASA configuration is the exact same. Also, he/she is using the same group policy, tunnel-group etc. as everyone else with the same setup.
This issue happens regardless if she has a PC behind the phone or not.Internal calls and external are both affected.
I am aware that most one-audio issues are RTP connectivity issues between the two endpoints. I can clearly see in the routing table of all of our routers, that the route to the subnet her phone is on has not changed for days, and she has had the issue within that amount of time.
I'm looking for a good place to start troubleshooting that doesn't require me to to a pcap. If all else fails, I will do a pcap.
I am unable to transmit e-mails to a friend , using "docomo.ne.jp" as her provider, and get no assistance from mailer-daemon at this end.
View 3 Replies View RelatedI am trying to hook up a wireless projector and connect an old audio mixer to my Laptop wireless and in sync so that I can operate the projector video and audio from my laptop anywhere in the room. I have a 30' by 60' sanctuary in my church an old audio mixer hooked up to key board, mics and speakers and one cordless mic. I am considering purchasing a Epson Powerlite 96W Projector and the optional wireless LAN module but wondered if there was a way to hook up a Epson EX7210 projector wireless as it does not accept the optional wireless LAN module. Also we currently have a great singer and no musicians so I am trying to find church presentation software that would include lyrics, background effects and music to accompany our singer.
View 1 Replies View RelatedIs there any remote access software which allows one to hear the audio of the computer connected to?
View 2 Replies View RelatedI had a requirement where I have to send the internet connection over 100m.As Ethernet supports clear transmission only upto 100m, I came up with this new idea (only in papers untill now). I believe RJ11 cables (normal telephone line) would be able to carry signals over longer distance as in ADSL broadband. plug the Ethernet cable which is already connected to internet source into ADSL modem. This ADSL modem will be connected to another ADSL modem which is at a longer distance away(let us say more than 100m or so.) The output of the latter ADSL modem will be connected to a computer/router which requires an internet connection.
View 9 Replies View RelatedI have a TV tuner card and Wifi router. Can I transmit the TV signal through Wifi router to my Laptop. How?
View 1 Replies View RelatedHow do I - from my stereo amplifier wireless transmit to two stereo speakers?
View 1 Replies View RelatedWe have a major poblem going on with our VPN router.We have a 7206vxr router which has an mGRE tunnel forming EIGRP neighbourship with about 800 remote locations using GRE over IPsec.
We have a problem where the EIGRP neighbourship keeps flapping intermittently and this happens to 30-40 locations at one time and very frequently.What I noticed was that the GRE tunnel transmit bandwidth was showing as 8 Mbps. I guess there is an option to change it.Will this 8 Mbps limit cause any issues of EIGRP neighbourship flaps and will increasing the bandwidth useful.
We are also seeing output drops on the tunnel interface.
pcvpnstore#sh int tu0Tunnel0 is up, line protocol is up Hardware is Tunnel Internet address is 10.254.254.254/16 MTU 17912 bytes, BW 30000 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 244/255, rxload 110/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source x.x.x.x (GigabitEthernet0/2) Tunnel protocol/transport multi-GRE/IP Key 0x328CDF, sequencing disabled Checksumming of packets disabled Tunnel TTL 255 Tunnel transport MTU 1472 bytes Tunnel transmit bandwidth 8000 (kbps) Tunnel receive bandwidth 8000 (kbps) Tunnel protection via IPSec (profile "dmvpn") Last input 00:00:00, output never, output hang never Last clearing of "show interface" counters 00:17:06 Input queue: 0/800/0/0 (size/max/drops/flushes); Total output drops: 732
I need a wireless router to transmit internet in my home, it's on two floors, my only concern is that the floor is really thick and I'm gonna be working in the basement. I need to choose between the following, can you tell me which is best?
View 1 Replies View RelatedI will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas. What is the maximum transmit power, 20dBm or 23dBm? I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.
View 4 Replies View RelatedI upgraded my 3602i survey ap the other day to the public image the other day and I have to say.. I've got it up and going of course, but I have a concern on the transmit power settings. Originally, the only option it gave me was MAX and -4, which I hadn't seen before, interesting.. -4 of what? 20? 17 probably or I though? At any rate, I went into the CLI to set the power manually, no issues there, though my options are not what I expected, maxing out at 25mw basically, which is fine but.. in setting it manually in CLI, the web interface reports an Error on transmit power. So.. does this work or not? Any survey with this image to verify it's power settings? 15.2(23c)
View 3 Replies View RelatedI bought my first Dell laptop (Inspiron 7720) and I can't make my bluetooth audiosystem (Logitech Mini Boombox) to work. I've got positive experience on Fujitsu-Siemens Amilo Xi2550 and on HP Compaq 6530b, where I had to just download another drivers for widdcomm bt adapter. I tried to do this trick o this computer, but I get only three bluetooth peripheral devices, which I can't install, because there is no driver for them. What shoud I do to make audio transfer through A2DP to work?Bluetooth drivers are working, I am able to pair the device. Problem is in instalation of all services.
View 1 Replies View RelatedI've got an ASA 5505 running 8.2 configured for solely as an IP phone proxy, it is the default gateway for the cucm box and PRI router, its inside interface is directly attached to the same subnet as all internal phones as well. Calls can be placed from either end, but after call is established, proxy phones does not hear audio from internal or pstn phones. The proxy phone registers with cucm with the remote internal IP of the phone that obviously cannot be reached by corp network.
Debugging from pri router shows the rtp traffic destination is the internal ip address of the proxy phone 192.168.0.50, why is the phone registering with its internal IP 192.168.0.50 rather than its Natted external IP 50.50.50.50 that can be reachable by cucm and other phones?Proxy phone is a 7945, after it registers, I do not see it under sh phone-proxy secure-phones, or sh phone-proxy signaling-sessions while on a call.
ASA Proxy config
interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 10.10.33.25 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 65.x.x.24 255.255.254.0!boot system disk0:/asa823-k8.binftp mode passivedns server-group DefaultDNSdomain-name ----.comsame-security-traffic permit intra-interfaceaccess-list inside_access_in extended permit ip host 10.10.33.10 anyaccess-list inside_access_in extended permit ip any host 10.10.33.10access-list inside_access_in extended permit ip host 10.10.33.5 anyaccess-list inside_access_in extended
[code]....