A few days ago, my lappy crashs (Blue Screen) and when i managed to get the page showing, start windows normal mode, safe mode or last know good config, i select the last known good config, But when i get into the windows, i have these message on my network icon saying limited or no connectivity. I run ipconfig on cmd, and got all
0.0.0.0
i have seen some of the troubleshoot advice on other thread on ipconfig/release, flush and renew but it doesnt works i tried to reinstall my drivers, but still the same, There wasnt any ! on my device manager, and i have selected the internet protocol, IP address and DNS, Automatically but still, it doesnt works
There is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
I've had trouble connecting to my own internet and have no wireless. I'm using my neighbor's wireless and it's really slowing her's down. I've tried restarting my laptop (it usually works) and then reinstalled the device under "device manager". It's not the cord, I've checked with my neighbor's laptop and it works fine.I use a Sony Vaio VGN-NS140E with Windows Vista SP2.
------------------------------------------------------------------------ {ipconfig /all} This is while I only have an ethernet plugged in and no wifi connection. Windows IP Configuration Host Name . . . . . . . . . . . . : FairyHo
I have a Dell XPS M1530 with Vista 32 bit. When i plug in a cable i get nothing, no error, and the comp does not recognize that a cable has been plugged in. I think that this started after my Hard drive failed and Dell replaced it but i'm not positive. No errors (? or !) in Device Manager and I can't find the Marvell 88E80XX 10/100 Ethernet Controller in device manager. I have attempted to Reinstall the drivers. The wireless is still working. I have one Light to the right of the port that is on all the time solid but no flashing with the cable in or out.
if I can use the encrypted port as unencrypted ethernet ports? url.. Each individual port on the Cisco Nexus 5010 switch is numbered, and groups of ports are numbered based on their function. The ports are numbered top to bottom and left to right.There are 20 to 28 ports on the Cisco Nexus 5010 switch, depending on which GEM is installed.
The 20 fixed ports form group 1 and are named 1/port_number. Ports 1 through 16 are unencrypted Ethernet ports. Of these, ports 1 through 8 are 10-Gigabit Ethernet and 1-Gigabit Ethernet-capable ports. Ports 17 through 20 are encryption-capable Ethernet ports.
I have a Cisco 857 router which i used for Internet connection with RJ11 connectior (ADSL0 POTS) but now the ISP has changed the internet link with PPOE type and the ONT connection is RJ45 , Is there a possibility to configure one os the Fast Ethernet ports as WAN port for internet.
My daughter is going to university. An Ethernet connection is provided but she wants to work wirelessly. Is there a gadget to attach to the Ethernet port that will create a wireless signal for her to connect her iPad and PC laptop?
watch netflix on my tv,which has netflix,but has a Ethernet connection,and must use a rj45 cable,can I change it over to a wireless signal,so I won';t have to use a cable?
Hotels have wired LAN connections and not wireless. Is there a device that will plug into the ethernet cable and offer wi-fi for more than one laptop/smart phone in the hotel room?
Laptop has 2 ethernet ports and receives the internet via one of those Ethernet ports. Can I plug a ethernet lead from my spare port on my laptop to a wireless router and create a wireless network (via the internet from my laptop)? Is this possible and how do I do it ?
I have a D-link WBR-2310 wireless router connected to a ZyXEL P-600 series modem. Everything worked fine untill a couple days ago when I had a power surge; since then the wireless router won't show on the modem that the ethernet cable is plugged in, and I get no wireless or DSL internet. I called the internet service provider, and they told me to reset both the modem and the router, which I did and it worked fine for about an hour; then it didn't recognize the cable again. I thought maybe it was the ethernet cable itself so I bought a new one, and it didn't correct the problem. When I hook any of the cables up directly from the modem to the labtop or the pc the ethernet light comes on and I have internet connection again. Why doesn't my router recognize the cable?
My dorms have wifi in the common room, and ethernet wall ports in the rooms since wifi doesnt reach that far. They both have the same network name (e.g. the wifi network is named 'apple', and when i connect through ethernet in my room the name is also 'apple') I need to have wifi in my room. So, if i get a router and connect it to the ethernet port in my room's wall, would that work? Is that all you have to do or is there some other stuff i should know about?also can i put a password on it? And also, will it carry the network traffic of the common room?(if two people are using the common room's wifi, will the wifi speed in my room be affected nd whatnot) i have a linksys router lying around at home (the blue one with the double antennas, everyones seen them, and the one in the common room is the same...wireless g)
im using linksys broadband router model no WRT54GC firmware version 1.06....im using it since 2005 still now i didn't face any problem, but since 3days im facing a problem all of a sudden. i.e im unable to connect through Ethernet port ( through lan wire) to my PC, but i can access router through wifi.when i connect through wifi it is saying that there is no internet access. but i can access my router administration.i cross checked with another pc and another connecting cable , but same problem, no use i also tried resetting my router, updated my firmware. no use.
I want to configure a Cisco Wireless Lan Controller (4400 and 5500 series) with to data ports for failover? I think the primary and secondary ethernet connections should be configured as trunks. I cannot find anything on CCO about this or on the internet per se. I know how to configure for failover with APs but cannot find anything on how to configure the controller in case an the ethernet port goes down.
I bought my laptop over a year ago. The wireless is really slow. I read other posts about this issue and found out that the network adapter(n1030) on this laptop is faulty or something. So I tried connecting to the internet using the Ethernet port.
The port shows up on my device manager.Realtek PCIe FE Family Controller.I know there is nothing wrong with the modem or the Ethernet cable because internet on the other computers in my house work fine.
I would also like to add that when I bought the computer, it came with windows 7 but had the ubuntu sticker on it. People in Fiji only mostly use windows so I guess the shop I bought this from did the change to windows themselves.
I was very happy working with my WRT610N connected to the ethernetport of my previous internet modem. Recently I had to switch to a new modem CISCO EPC3925. Unfortunately this combination does not work anymore. I don't get an internet connection on my WRT610N anymore. I therefore have to connect all computers (LAN and WIFI) to this EPC3925. Especially for the WIFI I'm not fully happy. My IPAD2 sometimes does not want to connect, a problem which never occurred when connecting to WRT610N.
I probably need to change a setting, but where? In the EPC3925 or in WRT610N?
I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the Ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.The switch port that is connected to the RAP and MAP is configured as the following:
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
WRT54GL has an option to restrict or share the bandwidth equally to each ethernet port or wireless? I need this option in a low bandwith area because the first computer connected to the router who makes some traffic (e.g. youtube) takes all the bandwith allocated by the ISP. url...
I am quite a bit rusty from my days of networking. I am trying to setup my lab so I purchased 3 cisco 2501 to study for my CCNA, my question is? I have 2 serial interfaces and 1 AUI for ethernet on each router. How can I configure the Ethernet interface, if I don't see it on the configuration. From the CLI command I issue the command show ip int brief. But It only shows the 2 serials but no E0 interface.
PS. I do have an Ethernet Transceiver connected to the AUI port on the router with a straight through cable going into a 2950 switch.
Is it possible my Laptop Ethernet port is dead?After I got home today I noticed that the store that passed by caused a short power outage. I knew this because several electronic devices that rely on constant power were reset.Next to be noticed was that my computer had no connection to the internet, and my Ethernet port has a constant orange light on.I proceeded to perform a full network restart for my modem, router, and computer. This solved the internet connection to my router. My roommate was able to connect via an Ethernet cable to the internet on any of the routers ports, but I was still unable.However,I was able to connect to the wireless on my computer. Unfortunately no matter what port, or cable I use my Ethernet port still is unresponsive to it all, and still has the constant orange light.you.Specs:Manufacturer: Gateway
Model: P-78 OS: Windows 7 CPU/Ram: Intel(R) Core(TM) 2 Duo P7350 2 GHz / 4090 MB Video Card: NVIDIA GeForce 9800M GTS Sound Card: NVIDIA High Definition Audio Conexant High Definition SmartAudio 221
The green light on my Ethernet port is always on. Even when I unplug the Ethernet cable and shut down my computer. The only way it turns off is when I unplug my computer from the outlet. Also, my computer doesn't receive any internet when an Ethernet cable is plugged in and the yellow flashing light doesn't show either. I know the Ethernet cable is fine and the internet works fine on other computers
The modem is sure working and so as the Ethernet cable since I am using it with another computer. I already had the driver updated but still it's not working. I actually suddenly heard noise in my computer before this happened. OS Windows 7.
Would a Linksys USB300M Network Adapter allow my computer to connect to the internet via Ethernet? My computer has an Ethernet port that doesn't work. I need Ethernet connection to connect to the internet through FIOS. I currently use an USB port on my computer to connect using DSL. I want to purchase a USB-Ethernet adapter that plugs into my USB port but has an Ethernet jack at the other end: USB300M Network adapter - Hi-Speed USB
I have my bigpond internet setup on my main pc,works fine connected to a router but i want to connect to the internet via ethernet cable on my 2nd pc. I have a ethernet port on the wall near it so that should work. I don't want to run a long ethenet cable from my router to my 2nd pc because there's a ethernet port right next to it.
getting near my home internet keeps shutting off and i lose the internet for half hour periods of time or more now im sure it will get worst as the storm gets closer. i run my cell phone usb tethered to the pc how do i setup my pc to share that internet from the ethernet cord so i can say run my xbox online plugged into the pc ethernet jack?
My custom built desktop is not recognizing an ethernet cord. The lights are not coming on when I plug it in. The device manager does not show network adapters. Im not sure where to find it/ not sure its there.
The ethernet ports across the entire campus including the halls all host multiple networks via one port. I connect to the port and I get one connection, and my friend connects to get a second connection through the same port, and a third person connected via the same port to get yet another connection. I think there may be 4 connections being hosted through this in total. Now, the university have 3 main streams of internet: 1 for Staff/postgrad, 1 for students, 1 for exchange students. The fourth connection type is intranet with only access to a portal. The purpose of the portal is to submit your mac address for wireless and ethernet to be assigned an IP address for both. The issue we are having is my friend needs to connect to the exchange students connection for actual internet access, but the ethernet cable will only connect her to the portal (all her details have been submitted). I have cycled through every window in the networking control panel and usually issues like this I can resolve within a couple of hours but how to identify other networks that are available through ethernet.
