RVS4000 Netgear WNDAP360 Will Be Connected To Ethernet Jack
Nov 9, 2011
I have a network closet where all the ethernet ports in each room of the house is routed to so wired routing performance must be good.I also need a good wifi network since we have multiple laptops and tablets we use around the home. I do have 2.4GHz and 5GHz devices so I need the dual, simultaneous wifi operation.The gear I can choose from to do this:
Asus RT-N56U
OR
Cisco RVS4000 + Netgear WNDAP360
The home is a 2-story unit and the networking closet is upstairs near the front of the house. If I go with the Asus RT-N56U, the wifi network will be centered in the network closet. If I go with the Cisco RVS4000 + Netgear WNDAP360, the Cisco router will be in the network closet and the Netgear WNDAP360 will be connected to an ethernet jack closer to the center of the house.
View 8 Replies
ADVERTISEMENT
Nov 2, 2012
On my closet's patch panel, there's one ethernet jack that is labeled "IDF5", I was just wondering what it is used for.
View 3 Replies
View Related
Dec 18, 2011
I received Centurylink DSL modem with hardware but my phone jack wiring was ripped out of wall,no wiring intact.what kind of jack and how to wire them to the jack. The wiring came thru wall are new kind with 4 pairs and have stripes on them.
View 1 Replies
View Related
Feb 26, 2012
I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Is there any way of making this Automatic.
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
View 3 Replies
View Related
Jul 24, 2011
I have an RVS4000 V1 router connected to a Comcast Extreme 100 mbps cable modem.The port setting for the port (number 4) is 1000Mbps Full Duplex, auto Negotiate.why the RVS4000 is throttling the port?
View 3 Replies
View Related
Jan 7, 2011
So my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies
View Related
Sep 14, 2012
Simple enough, my computer is connected to my modem/router hybrid but it will NOT connect to the internet. The router is providing internet just fine (I am currently typing this on my laptop using internet from that same laptop). I have tried everything. I've tried the different ports on the router, I've tried different ethernet cables, I've even had the modem/router replaced. None of this has worked, so I am convinced that it is somehow a problem with the settings of the computer which will simply not connect to the internet.
The computer will connect to the router (I can login and fiddle around with settings). I've tried re-installing the ethernet card's driver (it's built into my mobo). I've tried inputting IP and DNS servers manually, but nothing works.
Here is a copy of my ipconfig and my ipconfig /all.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersAlexander>ipconfig
[Code].....
View 7 Replies
View Related
Apr 29, 2012
I am trying to connect a 2nd PC to my Netgear Router DGN2200. The first PC is working normally with full internet capability. I have tried connecting the second with an Ethernet cable but it wont recognise it .
View 7 Replies
View Related
Dec 6, 2012
I have internet through my cable company and currently use their wireless netgear router. I purchased a Netgear Router N600 but it does not have a port for the cable connection. Can you recommend the correct wireless router
View 1 Replies
View Related
Apr 2, 2012
I have a netgear DGN2200 router with a USB port built in. I also have a WD External Hard drive, When using the hard drive plugged directly into my laptop I get transfer speeds of roughly 20 mb/s,However when I plug the hard drive into the router and transfer wireless i only get 1.2 mb/s.Also I'm looking to get a USB > Ethernet adapter, would this increase transfer speeds wirelessly?If not how do I go about increase transfer speeds?
View 6 Replies
View Related
Sep 30, 2011
I have read most of the responses to the same type of problem but none of them have got my XP pc to connect to the internet. I am using Wireles and LAN.My router was Netgear DG843N which was intermittently dropping the connection to the net. I tried corrective action but the problem continued.On the advice from Netgear tyech support,I tried just using LAN - that didn't work. Then they suggested using another router,so I purchased a Netgear DGN1000 Router.This did not resiolve the problem so I contacted Netgear who suggested several things to do.As the XP was connecting to the router both wireless and LAN we decided that it was not a router problem.All of my devices attached o the router ( printer - Vista pc- Win 7 laptop)are working correctly,just the XP pc that is not.
Details of the pc are :-
Windows XP Home Edition
Version 5.1.2600 Service Pack 3 Build 2600
View 14 Replies
View Related
Oct 11, 2012
My laptop says i am connected to the netgear but i am unable to access the internet-
View 1 Replies
View Related
Oct 8, 2012
I have tried 3 cables and all three are not recognized even though they are plugged in. I have uninstalled network adapter and re installed it and i have updated the driver still nothing so i don't know what to do next.my laptop is a hp pavilion g6 series
View 10 Replies
View Related
Jan 23, 2011
I have a Netcomm NB9WMAXXn router and 3 laptops i want to connect to it wirelesslyThe problem is that the iwreless internet connection slows down and eventually drops out after about 30m unless one of the laptops remains connected via Ethernet to the router. The wireless laptops will remain connected to the router but the internet connection will fail. The laptop with Ethernet connection retains a very good connection so i'm thinking this is an issue with my router or it's configuration
View 1 Replies
View Related
Jun 20, 2012
Have got one ethernet plug connected to the router and then one upstairs connected to my ps3, can I add another plug and connect another device to it or do i need two plugs to connect to another port on my router for it to work? If I buy another set of plugs will they still work or will they cause interference?
View 1 Replies
View Related
Aug 7, 2012
Am trying to fix my husband's computer, which seems to eb ok except that it cannot connect to the internet. The connection is wired and works fine (my computer, next to his, works well). I have tried pinging google.com and cannot resolve, but pinging numerical addresses works fine.
View 1 Replies
View Related
Apr 22, 2011
i acces internet on my pc using tata photon+ mobile broadband service,my problem is that i bought a ps3 and want to share internet connection with pc using ethernet cable via lan modem, for this i connected ps3 and pc using ethernet cable,i go to custom and wired setting of ps3 but my ps3 keep saying 'connect ethernet cable'.
View 7 Replies
View Related
Nov 8, 2012
my ps3 keeps saying ethernet cable not detected but it is connected.
View 1 Replies
View Related
Nov 1, 2011
I have a 2wire modem and I'm using att DSL. The internet was working fine, I went out of town for 2 days, I returned to find my internet wont work. During the time I was out my brother said it hadn't worked for the 2 days. The modem works fine and all lights are green when my desktop is turned off or not connected. It even lets my brother use wireless on his laptop. However, when I turn on my computer or when I connect it to the modem with an ethernet cord, the DSL light will go red and not work.
View 7 Replies
View Related
May 11, 2011
I have a problem concerning my Netgear XET1001 85 MBit/s Wall-Plugged Ethernet Adapter. My personal computer in my room is connected directly to our router and I'm getting arround 14-15Mbps download speeds. My parents computer is located in a different room and I bought them the Netgear Adapter thinking this was the most effective and simplest solution. Better than a Wifi-Adapter. I cost me quite a lot too to be honest. The problem is my parents are getting speeds of 0.05Mbps and the browser often doesn't even load the pages completely. To me it seems like the data can only travel through the thing very hardly if at all.
We thought this might have to do with the age and RAM of our computer. (512MB of RAM) So we bought a new one a couple of days ago. Turns out: nothing has changed.
The Wall-Pluggs are connected directly to the outlet by the way. I'm trying to give you the most amount of information I can think of so one more thing might be important. Yesterday I brought my parent's PC into my room, connected it to the Wall-Plugg and got speeds of 5Mbps. Although this is better, it's not what I bought this thing for. Even a WIFI connection would be faster would'nt it?
View 11 Replies
View Related
Oct 18, 2012
I am having problems connecting my PC (Win7) to my Router (Netgear DGN2000) via ethernet cable.Wi-fi is working fine but I want to speed up my connection using the PC's Gigabit port. Here are the problems:
- When connecting via wi-fi everything is fine
- When enabling my LAN WITH wi-fi still enabled I lose all internet connectivity
- When enabling my LAN and disabling wi-fi lose all internet connectivity
Here is my IP Config when both are enabled :
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig
Windows IP Configuration[code].....
View 4 Replies
View Related
Feb 28, 2011
My dad is using a netgear router DG834G V2 and has no problem until recently. He got a new phone and wanted to connect wirelessly but couldn't remember is network key. After playing around with things he's obviuosley changed something and now has no internet what so ever.
I've tried plugging in the eternet cable and accessing 192.168.0.1 but can't see any problems there. When i am able to get a connection it's local only and Internet explorer can't display web pages. And when i unplug the ethernet cable it doesn't always find the wireless connection, and if it does find it, then i have the same problem as when the lead is plugged in.
His ISP is AOL although he doesn't always access the internet via aol, he'll use IE and i'm trying to get him to give firefox a go.
I have tried disabled both windows firewall and AVG firewall and individually but still keep getting the message internet explorer cannot display webpage.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Dave-PC
Primary Dns Suffix . . . . . . . :
[Code]....
View 1 Replies
View Related
Jun 14, 2013
I have an existing Ethernet 100meg LAN and I want to add a wireless capability. I have looked at some products and it is confusing. Range extenders for about 40-50 UK GBP (equiv $65 US). Eg Netgear WN3000RP or WN2000RPT. But they mention extending the range of an existing wireless network?
View 2 Replies
View Related
Nov 4, 2011
My desktop was connected to wireless router by ethernet cable but it seems the ports on the router are now US. Bought netgear N300 USB adapter and installed. Had problems getting "limited connectivity etc" messages 'cos wasn't getting IP address allocated. Have now manually allocated IP address and connection status is now "Connected" (with no warning about limited connectivity etc). However I can't connect to the internet.
View 12 Replies
View Related
Apr 6, 2011
I have a Netgear Wireless Adapter WNA1100 and I'm trying to connect my 2nd desktop comp using it. I'm having trouble staying connected. The wireless connection says 100% but when I ope IE and yahoo homepage comes up it only stays connected for a sec and it says "unable to stay connect, do you wish to work offline" then it automatically put in offline mode, which doesnt work. Now it's saying IE cannot display webpage.
View 2 Replies
View Related
Jun 3, 2012
Tried to set up with my AT&T dsl moden. Cannot access internet when everything is connected. At&t says they do not support Netgear, so they couldnt facilitate. They sell Netgear on their website.
View 1 Replies
View Related
Apr 22, 2011
A friend recently re-installed windows XP on their HP Laptop. They were connected wirelessly with a Linsys router (model wrt54g.1) and an RCA Cable Modem. The Cable ISP can ping the modem and gave me the IP address over the phone. I cannot ping the modem even when I take the router out of the loop. The network card (i1394) in the Laptop is functioning normally and I can see traffic on the modem (both the Cable Internet light and the PC activity light are flashing green) the ethernet port on the laptop is also flashing (amber). However I cannot reach the internet and cannot even ping the modem. The modem is brand new..
View 2 Replies
View Related
Jun 10, 2012
I have a desktop running windows XP Professional x32 SP3 and my network adapter is a Realtek PCIe GBE Family Controller. The desktop is connected to the network with an ethernet cable.Up until yesterday the internet connectivity just stopped working. I am seeing a very low number of received packets as opposed to the high number when it was working. It is showing that it is connected to the network but I still can't access the internet. Also I should mention that the desktop is at work and it is connected to a DHCP server that assigns IP addresses. I have updated all the drivers and I have used Winsock Fix and Netsh but it still isn't working. However the weird thing is that if assign a static IP address to it...it works. But I can't do this because I am not suppose to hook it up to the ports assigned to the switch for static IP's. It has to be connected to the DHCP switch. Why does it work when assigned a static but not if it gets an IP assigned by the DHCP server or switch. Also even if I try to reset, renew or release the IP...when I connect again it still gives me the same IP. It wont change.
View 1 Replies
View Related
Nov 4, 2011
I have a net gear WNR2000vs with the latest firmfware to date.wired devices connected: 1. my pc 2. xbox, and also one wireless device connected to my cell phone via wi fi.
View 9 Replies
View Related
Dec 5, 2011
So i'm living in an apartment and brought up my pc desktop from home, issue is that the internet cord was not long enough to connect from my room to the modem outsideTheres apparently an internet jack in my room and i have no idea how to set it up to respond to the modem thats currently placed in the living room.
View 1 Replies
View Related
Mar 21, 2013
So, for some reason my internet connection started disconnecting about every 1-5 minutes. It worked fine this morning, however, when I turned my PC on a few hours ago it became very unstable. After it happens I have to reconnect to internet (it doesn't work all the time, I usually have to do it two times for it to work), and then again after a few minutes the connection dies. Tried restarting my computer, tried restarting the modem, tried the troubleshooting network thing (it keeps saying "Local Area Connection doesn't have a valid IP configuration", but gives no solution). Also, I tried connecting on my cellphone and on a laptop and both of those work. However, those connect through WiFi, while my PC is connected through an ethernet cable[code]
View 4 Replies
View Related
Mar 8, 2012
Could the new internet card be making my downloads and emails VERY slow or is it bad line speeds. Would a new modem router improve things.
View 1 Replies
View Related
Apr 28, 2013
I have a strange problem with a SG300-10 (our first SG300) working as a desktop switch.When a PC that is connected to the switch is powered off and is later (a few minutes or next day) switched on, the PC has a ethernet-connection to the switch, but no IP-connectivity.The PC-statistics shows that ethernet is connected and it sends packets, but the PC does not receive any packets.At the same time the SG300 statistics for the port says, that the ethernet is connected (same paramaters as the PC) an that the switch is sending IP-packets (broadcast and unicast) to the port, but does not receive any packets. The switch shows follwing entries in the ram log for the port: [code]
With the older firmware 1.2.9.44 the IP-connectivity worked after waiting 5-10 minutes.With the new firmware 1.3.0.59 I can wait even 15 minutes, there is no change and nothing happens.But when I change some "unimportant" parameters of the port (i.e. change port speed from autonegation to fixed 1000M, or vice versa) and then save the running configuration to the startup-config, around 5-10 Seconds after the configuration is saved, the port gets full IP connectivity and after that works fine (until the PC is switched OFF and ON the next time).This is a very strange behaviour. As "PC" I have tested this with HP-workstations, Lenovo Thinkpad and a MAC Mini. The switch "reacts" to all the same.Following I have attached the config of the switch. [code]
View 3 Replies
View Related
