I have my xbox plugged straight into my router as the wirless connection was awful. Thought this would make it better but its also bad! I noticed my NAT is not open, so i went onto my router settings through the browser to edit some settings to make my NAT open, however it asks me for a password, ive never put a password on it and havent got a clue what it is.
View 7 Replies'm having problems accessing the configuration utility of the *second* router in my daisy chain. Here's my setup. I have one router (router 1) on ground floor which gets internet from the modem. That router is then plugged into the LAN port of a wireless router upstairs (router 2). My laptop is then plugged into another LAN port on router 2. This allows me internet access as intended. But I'd like to log into the the configuration utility of router 2. But when I type the IP address of router 2 into my browser (192.168.1.1), it takes me to the configuration utility of router 1. Router 2 is out of the box--I haven't done any configuration to it (for example, changing its static IP address).
View 2 Replies View RelatedIm getting internet but i cant access my router address to get my config page. I had broadband wired internet a few days ago but now im using a wireless connection could that be the problem?
View 1 Replies View RelatedUnable to access router admin page for Haier model R800
View 1 Replies View RelatedI am able to connect to TPlink router through my pc but unable to access internet.The router is unable to detect dynamic ip.
View 1 Replies View RelatedI have the issue of being unable to access my router configuration page. My standard gateway IP (83.226.48.1), does not work, resulting in "unable to connect". If I try with my IPv4-adress, it just comes out with a blank page (Mozilla Firefox and Internet Explorer).
View 17 Replies View RelatedFew months back i had upgraded my Lynksys router with Coova AP firmware. Everything was working fine.I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet. Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this.
how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router. Can somebody tell me how to achieve this?? Or atleast what user id and password should i try to log in to router?I tried to use telnet command on the router (Connected router to linux based computer with ethernet cable). But telnet also not working. It is not asking for password, and it saying disconnected.
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times. Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. How to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router
View 4 Replies View RelatedLost connection to Internet though router appears normal. Belkin router, MacBook.
View 1 Replies View RelatedI have a Belkin F7D2301 v1 (01) and I am having the exact same issue. I like to do surveys and I've never been able to access this particular site It does the same thing as the original person's problem. I'm kind of scared to change anything on my router setup because I have several computers on the same router. Will any of this cause the other computers not to run on the router?
View 2 Replies View RelatedMy Linksys Routers IP is 192.168.1.1 am unable to access the console, although i changed the computers IP 192.168.x.y. i have tried by Hard Resetting the Router but still the same?
View 1 Replies View RelatedJust to set the stage, we used to have a network which ran in the following order:
For wired workstations: bridged DSL modem->wireless Linksys E900 router->Dell PowerConnect 2824 switch->2 modular 4-port jacks->individual workstations For wireless: bridged DSL modem->wireless Linksys E900 router->workstations The workstations were set up to pick up IP addresses automatically.After an infrastructure upgrade where we added some Cat6 cables and swapped the modular jacks for a patch panel, we lost all connectivity. I restored the connectivity to the wired workstations by assigning IP addresses. But we have no wireless and I cannot access the router GUI at its IP address (even when plugged directly into the router). All the workstations show the default gateway as 192.168.10.1, so I don't know what's going on.
I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
View 3 Replies View RelatedJust got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
I have a Linksys E4200 router
after updating to smart wi-fi I can't access the USB FTP or off network.Only way it's accessible is from the computer the router is attached to via network drive.FileZilla gives me this error....."Connection attempt failed with "ECONNREFUSED - Connection refused by server".I've reset the router same problem.
View 9 Replies View RelatedI cannot access this router. I have a cable modem from Comcast Is there any way to clear info, I have reset 50 time and it will ask for uname & paswrdWhat shall I do?
View 1 Replies View RelatedI am trying to setup a DIR-601 wireless router (Hardware Version: A1 Firmware Version : 1.00NA ) with my connection from Astound.I am able to connect to the internet from the cable modem (Motorola SURFboard SB5101) but I am unable to get it to work through the router. All the lights on the router look ok.When I look at the WAN status from the router setup page I see :
WAN
Connection Type : DHCP Client
Cable Status : Connected
Network Status : Disconnected
Connection Up Time : N/A
[code]....
* I noted that the router did not show me the correct time. Is that normal ?I have even copied my laptop's MAC address but it did not work. I restarted the modem and the router a number of times but to no avail.
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router.
I've been trying to configure a TP-Link L-WR740N to act as an access point using the instructions here as a guide. As stated in the guide, I've been changing the IP address of the TP-Link router to a new address that lies outwith the pool of available DHCP addresses in my combined modem/router but with less than resounding success. After rebooting the TP-Link router, I am unable to access the set-up interface - the newly allocated IP address doesn't work, neither does the original IP address work. What is happening here? If I change the IP address to one that lies within the DHCP pool and reboot, I can access it ok with the new address. However, that obviously clashes with the set-up instructions.
View 1 Replies View RelatedJust a day or two ago I was able to do what the title says, didn't make any adjustments to my E2000 while in it, had to find something though.Anyhow, connecting to http://192.168.1.1 results in "Unable to Connect", etc. Also tried it in IE9, Firefox Beta is my primary, and it still didn't work. Tried using Cisco Connect and it says it cannot connect to my router. I am wired to my E2000, which in turn is wired to my DSL modem (Actiontec GT701D-Its firewall not in use). I sitll have full connection to the internet as well as other wireless deveices do in my house.
View 1 Replies View RelatedHere is my setup.Using all MAC OSX I have AT&T DSL ISP connected to a (ISP provided) Speedstream 5100 Modem.I just purchased a Cisco Linksys 5200 N Router and I cannot access the internet. I followed the set-up instructions to the T but to no avail. I cannot find anything online about these two devices being incompatable. Do I purchase a new modem? If so how can I be sure it's compatible with the router?
View 1 Replies View RelatedI trying to portforward on my WRT54G2 router but can't access webpage because I don't know the username or password. Is there any way to find out the password and username
View 1 Replies View RelatedI have had my router for about a month and all the wireless lan stuff seems to be brilliant. Recently I signed up to an ISP (Plusnet), and can't access most websites. The ISP has told me that I should take this up with my Router company. I seem to be having the exact same problems as this guy was having [url]....
View 1 Replies View RelatedI've got a v1 E1000. Lately when I turn on one of my computers, or attempt to connect with my Motorola Xoom tablet it will show connected but I will not have internet access. Initially it will show that I have internet access but not work, then after about 1-2 minutes my PCs will show "No Internet access" for about 2-3 minutes, then it will show "Internet Acess" again and still not load. After that, in about 1-3 minutes the internet will start working and work as good as ever until I disconnect (manually or by turning off my computer) then connect again; the process described avove happens again.
View 2 Replies View RelatedI just bought an E4200 and it was working perfectly, very easy to install, all that it promises. Then I had an energy peak. For some reason, don't ask me why, I did RESET the router not thru the web nor thru Cisco Connect, but pushing the reset button at the back. I can't access the router anymore ! It keeps asking for a password that is never accepted. I have uninstalled cisco connect and tried again. Nothing. The router is not found. Keeps asking for a password. I tried everything: blan+admin, admin+admin, the password I used to have (provided at the cisco connect uninstall).It seems that the RESET never worked. The router is working thru cables, meaning when I can connect to the internet wired. But the router is never found wireless.How could I update the firmware if the router is not recognized (or if I don't have a username+password) ?
View 9 Replies View RelatedI have a continuing problem with my WRT54G2 wireless router. I set up my network, changing the password for the router, and I change the SSID, as well as the encryption password. When I set it up, and after changing passwords etc. I always log off, go back and log on, and it works fine. Once I set up the network, over time, I'll notice a device will no longer connect via wireless. When that happens, I try to log on to the router, and can not connect to the router using either Firefox or IE. When I try, I get Internal Server Error, or just nothing. I can ping the router, and if I run an IPCONFIG at this point, the default gateway does show 192.168.1.1. Every time this starts to happen, I must do a hard reset of the router. Once I do this, I can connect, and log on using the default settings, and re-set everything. This is a HUGE pain, as it takes a lot of time, and happens way too often.
View 2 Replies View RelatedI recently bought the E4200 v2. When I first installed, I ran the firmware update and then performed a hard reset (push reset button for 20 secs). I then began to enter all the PPPoE information and network settings into the new router (verified these settings with the existing WRT54GL router I'm current using and they all matched). I then disconnected the old router, and powered up the E4200. I was able to access the new router (192.168.0.1), I could see all previously shared files/computers with the new router, but I could not access most websites - usually I got a timeout error, or they eventually loaded in 10x the usual speed. This was typical of both laptops - one wired, and one wireless. My wireless handheld device could connect to the wireless network, and ran a speeedtest.net test, and upload/download speeds were normal - but I could not access the internet from the device. When I switched back to the old router, everything worked perfectly again. I have tried some suggestions on changing MTU values, but that did not seem to make any difference.
As a work-around, I have ended up keeping the WRT54GL as the main router and using the E4200 in bridged mode for wireless only (not what I ideally would like)..
I am unable to access my router through the ip address (192.168.1.1) even though I have verified that is the address. To be sure, I did an ipconfig release/renew, but no results. I want to limit a user's network access by MAC address and I don't think I can do that without accessing the router thru the ip address.
View 2 Replies View RelatedI'm unable to access my linksys wireless g broadband router (WRT54G)'s access gateway. (192.168.1.1)The gateway page doesn't load, at all. It doesn't ask for the user or password at all. On any of my internet browsers (firefox, and internet explorer)Anyway of fixing this would be appropriate.
View 2 Replies View RelatedUpon attaching my external storage I was able to create a share, copy files and access it successfully from everywhere. Now when I attempt to add an additional share, the router lets me create it but when I try to move access groups over from the available groups, the >> buttons are greyed out. The one working share has the admin and Everyone groups with access. Any additional share I create has the admin group in it by default, but I can't add any more groups. I am logged into the router as admin and logged into the pc as a local admin. I am also unable to change the rights from my pc on a share (access denied). I AM, however, able to map a drive to a new share successfully, but when I copy files over, a few minutes later the filenames are there but they show up as 0 byte files.
View 7 Replies View RelatedI've been on DSL with British Telcom Infnity (FTTC) since March and had no problems with the service. My router, however, an Apple Time Capsule, was not so reliable and needed a reboot every few days,So I just purchased the E4200 V2The Setup completes OK and PPPoE logs into my ISP fine. But then I hit the problem.Most of the websites I use simply won't load . In Safari on my OS X Lion, Macbook, I get an error like this "Request Timeout. The server timed out while waiting for the browser's request. Reference #2.525fdd58.1336048435.0" In IE on my Windows XP laptop, the error is "Internet Explorer cannot display the webpage"But some websites still load fine. So [url]..., loads instantly. Most other sites I try, including [url]... - won't load at all. (Plusnet is my ISP)If I connect to my work VPN, I can browse as normal
View 9 Replies View RelatedI just bought a Linksys E1500 router and followed the CD instructions for setup. It is wired to my desktop and I am unable to access the internet. If I go direct to the modem and bypass the router the internet works fine
View 3 Replies View RelatedI have a Cisco outer EA2700 connected using a Lan cable, Lan cable works fine as I connected it directly to my PC, I am unable to access wifi network connection, I am able to search the router and also able to cnnect to the router, But wireless connection shows limited or no connectivity, and unable to access any websites. It was working fine till yesterday, I tried rebootng ad also unplug and replug the network cable also reset the router but does not work
View 1 Replies View Related