WRT54G V6 Router - Ethernet Cable Speeds Up The Transfers?
Nov 21, 2011
I have a WRT54G v6 router and I am trying to get higher speeds from a wireless network, I have set up a dish and a cantenna and is going really well about 18-22dbi gain which is very noticeable but I have a question, does an ?Ethernet cable speeds up the transfers Like the Upload and download speeds will be faster? like a high speed cat7 or cat6 cable that can transfer data at much higher frequencies? I have cat 5 and get around 13Mbps, will cat 6 get me 16 or 17? or the router can't handle it?.Also another question is how can I make the gain on the dish higher?
View 2 Replies
ADVERTISEMENT
Jan 18, 2012
I have DOCSIS 3.0 modem and a Linksys E1000 wireless router with which I get reults from SpeedTest of 8.6 mps down, 1.57 mps up up from 15 mps service from cable provider. Connected to modem via ethernet cable produces 16.0 speeds. Do I need to upgrade the router or are my settings wrong?
View 1 Replies
View Related
Mar 14, 2011
Linksys WRT54G v5 Router
Arris TM502G/CT Modem
Whether it be downloading or just trying to watch a video on youtube. For some reason everytime I try to download something it appears to start fast but then it basically just stops. I'm running windows Vista and I've tried going into the router security settings and unchecking Block Anonymous Internet Requests.
View 1 Replies
View Related
May 19, 2013
My Belkin F7D4301 Router has the fastest wireless speed of maybe 2MBps but wired with a cat5e cable to my asus laptop of almost 7MBps. I have a one smart TV, one blue ray, one roku, and a nexus 7 using the 2.4 channel.
My Wireless 2.4 settings are channel 11, Extension channel 7, Wireless mode N (have tried with just g and b, g, and n modes), Bandwidth 20/40, Protected mode on, QOS off.
I've talked to Belkin tech support, they are the ones who had me set up my 2.4 channel this way but my wireless speeds stay just under 2MBps, they just want to keep sending me the same model Router because they think each of the new ones they send me is defective.
Am I doing something wrong or is 2MBps the best wireless speed I'm going to get?
View 1 Replies
View Related
Jun 27, 2011
I have both the WRT54G and a E1000 wireless routers and this problem is occurring for both of them.I use AT&T DSL and the speeds are fine when it is :
1. Not plugged into router
2. Wireless Network Mode is disabled through the router configuration page, having all devices wired.
However when wireless network mode is enabled, speeds drop significantly, 15~17 ms ping goes to 250~800 ping, and download speeds are way lower also. When the router is reset, the regular speeds will return for maybe 30 seconds to 1 minute, then it'll drop back down. I'm positive there's no outsiders connected to my network and this problem still occurs, only when the router is giving out wireless signals. Sometimes the problem randomly goes away for a while but it will always come back. I've tried many things, firmware upgrades, factory restore, none of them seem to work, the only solution so far has been to disabling it, but I need it to be on as there are other devices in other rooms of the house that need WiFi to connect to the internet.
View 9 Replies
View Related
Apr 28, 2013
Is there a difference in an ethernet cable and an Ethernet networking cable? I have an Ethernet cable and a 6 port splitter I am trying to connect. I have 4 ports in the router that are in use. When I connect them to the splitter nothing s working.
View 1 Replies
View Related
Feb 24, 2012
I have a WAG160N wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.
What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ?
View 1 Replies
View Related
Jul 2, 2011
These questions are only in relation to the above Wireless Router (v6, FW-v1.02 [2010]) :
1. What is an Ethernet Bridge (the basic authoritative definition), and besides gaming, what are they generally used for in a business setting?
2. What are VPN settings in a Router used for, and can a VPN be configured on a remote PC without them?
3. Utilizing bridging, etc., can I utilize my WRT54G as a makeshift Range Expander as long as the primary router doesnt have WEP key requirements? The current WIFI doesnt reach my PC, so I thought I could configure my router midway in hopes of extending the other routers' signal, via some kind of bridging if necessary. Naturally, there would only be a wireless connection between routers.
4. How can I setup a simple Captive Portal on this router?
View 1 Replies
View Related
Feb 22, 2012
We have the Cisco WRT54G wifi router in many offices in this building. This router has two antennas. These antenna are screw into the back of the router unit. The antenna is male and router side is female of the connector. what are these connectors (some type of RF connectors)? How can we get extension cables for these to move the antenna from one fix location to another point?
View 4 Replies
View Related
Aug 8, 2012
I am having a problem with my Realtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC. It is not detecting my ethernet cable, and thus leaving me without internet on my desktop, after i updated its driver. The cable is not the problem as I have tested the cable with my laptop. I tried rolling back drivers, doing system restore and removing drivers with driversweeper and letting windows install the drivers again. However, none of these worked for me. I doubt the NIC is faulty as it was working before i updated the drivers. I am using windows 7 home premium 64-bit.
View 9 Replies
View Related
Oct 4, 2012
At the moment I cant run an ethernet cable through my house from my router to my desktop PC (Which is where I use the internet/play games etc) and connect directly that way because my parents dont want cables going through the house etc etc.For the past 2 months or more I used my old laptop to pick up the wireless connection downstairs then I bridged the connection and used my ethernet cable from the laptop into my PC/Xbox or whatever, no problems until today, I wouldnt even have to log into the laptop, i would just turn it on and leave it at the login screen and I would have internet on my desktop/Xbox.Tried to do that today and was getting unidentified network on my desktop, i dont know what the problem is, I can connect directly to my router with the ethernet (I tried it) but not the old way anymore, i'm on the laptop now on the wireless internet.In network connections there LAN network isnt there anymore, its just the 'Unidentified Network' which is the bridged connection.
View 8 Replies
View Related
Jan 4, 2009
I am running a wrt54g and I was woundering what is the longest rj45 cable length I can run?
I notice running about 30 plus feet connection does not work. When I cut off about 5 feet it worked. Seems I can only run a ceratin amount of cable length with this router.
View 8 Replies
View Related
Mar 7, 2007
I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.
View 9 Replies
View Related
Dec 24, 2012
So this morning I was planning to reset my router because my internet was feeling a bit laggy. Omce i did, its lights turned on except for the ethernet light.It was working perfectly last night
Ive tried resetting the router a few times with no results
ive ran the Windows troubleshooter with it recognizing that:
The Local Area Connection adapter is disabled: Detected
Enable the wired network adapter: Not run
View 3 Replies
View Related
Feb 17, 2012
Recently purchased a Linksys E4200.Computers on network:Two hard-wired gigabit desktops: one Windows XP, one Windows 7One hard-wired 100mbps desktop running Windows 7One laptop with an Intel 4965AGN running Windows 7.File transfer rates between any of the desktops and the laptop is very slow: ~2 megabytes/s
File transfer rates between the gigabit desktops is good (~50 megabytes/s, hdd bottleneck), transfers between the 100mbps desktop and one of the gigabit machines gives ~10 megabytes/s.Currently running on the 5Ghz band, connected with N at 300 megabits, good signal strength. Disabled mixed mode on this band, enabled N-only.Use a scanner tool, I can tell that there are no other networks on 5Ghz band.Also, tried 2.4 Ghz band and got similiar low speeds.These transfer rates are much below what other people report for real-world throughput. Any ideas? I know there is an Advanced Wireless config page, is there a setting there that might work if adjusted?
View 1 Replies
View Related
Feb 5, 2013
I am recieving error 619 (port for connection was closed) when trying to connect over my wireless connection. If I disconnect the WRT54G and hard wire to the cable modem I can VPN in without a problem. I have enabled IPSec / PPTP / L2TP on the VPN security tab and have reset the wireless modem.
View 4 Replies
View Related
Dec 30, 2011
I was using Billion ADSL 2+ modem since last 6 years. It was working well but I need Wireless LAN N speed connection and I bought Linksys WAG320N.After configuring the modem my download speed has come doen't to less than 1Mb/s. When I connect to my old Billion I am getting 16Mb/s. [code]
View 2 Replies
View Related
Oct 28, 2011
I've been using the Linksys router e1000 N type for a week now and it hasn't beeen such a great experience. The thing is when i connect the modem to my laptop via ethernet cable internet works but not when i connect the cable to the router even though this worked before. actually a few hours before. so i dont know whats happened to my router since clearly the problem is in there. the modem has lights for PC Cable DATA and POWER. The lights to all of them blink when i have connected the modem directly to laptop but the PC light is non existent when i connect it to router. hence i get no internet access. the routers power is on so i dont know what the prob is ive rebooted it a few times but to no avail.
View 1 Replies
View Related
Feb 14, 2011
i have a DSL connection which is established using a dial-up (PPPoE) modem. I recently bought a wifi router, and I found that when I plug the cable to one of the LAN ports and the laptop, it seems as if it wasn't connected at all (not detected on either side).I tried to format the system running on XP and I installed windows 7 but the problem persists.The only thing I can think of right now is using a crossover cable, but I somehow doubt that it should work since I tried plugging the router to my netbook (using a normal cable) and it worked like a charm. But maybe the fact that it's a quite old laptop (PB MV51-101) has something to do?
View 8 Replies
View Related
Sep 24, 2012
HAVE AN ETHERNET SOCKET FOR MY INTERNET BUT WOULD LIKE TO BE WIRELESS MY ROUTER ONLY HAS AN IN PORT FOR PHONE ?
View 1 Replies
View Related
May 19, 2012
I just bought a 30m CAT6 cable which I installed inside the house, now since my router is on the floor above me I bought a 30m cable to be able to have it downstairs. I don't really know if it has something to do with the PC or if it is the length of the cable that is the problem. But when I try the PC on the main floor the speed is 15-20mbit/s and when I try it on my PC downstairs, all I get is a maximum of 10mbit/s. The strange thing is that ping/jitter is the same both upstairs and downstairs?
View 5 Replies
View Related
Jun 7, 2012
at my house if i replaced a cat5 cable with a cat6 would i see increased download speeds?
View 5 Replies
View Related
Jan 30, 2011
I just recently purchased a Linksys WAG320N and replaced a setup with Linksys AM200 modem and a good ole Linksys WRT54GL. Problem is that after the switch i immediately got around 100 KB lower transfer speeds no matter what source i use or kind of transfer i perform. If i earlier got for example 860KB/sec i now only gets 760KB/sec.I´ve set the modem/router up pretty much using the default values, are there any settings i could change to get a more efficient use of my bandwidth? I am using the provided network cable that came with the WAG320N, but i have also tested with other cat 5 cables. The file transfers are taking place using cable attached devices only.
View 9 Replies
View Related
Apr 30, 2011
I have a Dell XPS M1530 with Vista 32 bit. When i plug in a cable i get nothing, no error, and the comp does not recognize that a cable has been plugged in. I think that this started after my Hard drive failed and Dell replaced it but i'm not positive. No errors (? or !) in Device Manager and I can't find the Marvell 88E80XX 10/100 Ethernet Controller in device manager. I have attempted to Reinstall the drivers. The wireless is still working. I have one Light to the right of the port that is on all the time solid but no flashing with the cable in or out.
View 14 Replies
View Related
Dec 13, 2011
I have only one computer right now.Had two, and got very weak signal to laptop (since discarded) upstairs from Linksys g 54Mbits downstairs at main desktop computer desktop.I have tried three different kinds of 54Mbits wifi routers, all with no success.I'm going to get my wife a new wifi laptop for Christmas, and she wants to be able to use it all over the house.The 54Mbits will cover the downstairs, but, based on previous efforts, I am thinking of putting my modem in the garage, where the cable enters my house, and using a splitter on the cable coming out of the modem to make two IN cables, using one cable for my comp and a 54Mbits router (for downstairs coverage), and putting a second wifi router on the end of the upstairs cable, to cover the upstairs rooms.My house has cable outlets in every room, so I won't have to do any wiring.
I plan to leave the routers on all the time (at this time) subject to how much of a bandwidth drop they cause. I have a 100 Mbps connection, and I play games, so I'd like to retain as much bandwidth as possible. I assume the two "on" wifi routers will pull zero bandwidth as long as the laptop is off. (??)Or maybe I should just try an "n" wifi router, since they get twice the distance, and forget the cable splitter idea.
View 7 Replies
View Related
Feb 1, 2013
I'm currently running Windows 7, and I have this issue where from time to time I am booted from my internet with the error saying either one of two things, one being; No internet access but it does show I am connected to my router, and the other being; plug in an ethernet cable. My 2 brothers on the other hand are both connected to the same router through cables as well and neither have this issue. Both issues seem to simply fix themselves by just waiting, but the disconnects are killing me.
View 2 Replies
View Related
Jun 13, 2011
My Ethernet cable connecting my computer to my router is not working. It was just working a few days ago and I have connected it to a different computer and it worked on that
View 1 Replies
View Related
Dec 6, 2012
I have internet through my cable company and currently use their wireless netgear router. I purchased a Netgear Router N600 but it does not have a port for the cable connection. Can you recommend the correct wireless router
View 1 Replies
View Related
Jul 10, 2012
I have a D-link WBR-2310 wireless router connected to a ZyXEL P-600 series modem. Everything worked fine untill a couple days ago when I had a power surge; since then the wireless router won't show on the modem that the ethernet cable is plugged in, and I get no wireless or DSL internet. I called the internet service provider, and they told me to reset both the modem and the router, which I did and it worked fine for about an hour; then it didn't recognize the cable again. I thought maybe it was the ethernet cable itself so I bought a new one, and it didn't correct the problem. When I hook any of the cables up directly from the modem to the labtop or the pc the ethernet light comes on and I have internet connection again. Why doesn't my router recognize the cable?
View 1 Replies
View Related
Oct 15, 2012
I have a huawei 521i router that I recently reset back to factory settings. I have been trying to set up my wifi but something is wrong. I can connect with my ethernet cable but not wifi. I have set up my wireless connection and I can see it in the list.
View 1 Replies
View Related
Oct 18, 2012
I am having problems connecting my PC (Win7) to my Router (Netgear DGN2000) via ethernet cable.Wi-fi is working fine but I want to speed up my connection using the PC's Gigabit port. Here are the problems:
- When connecting via wi-fi everything is fine
- When enabling my LAN WITH wi-fi still enabled I lose all internet connectivity
- When enabling my LAN and disabling wi-fi lose all internet connectivity
Here is my IP Config when both are enabled :
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig
Windows IP Configuration[code].....
View 4 Replies
View Related
Feb 17, 2013
I'm using a refurbished WRT54G2 v1.5 router. I've had the router for two and a half years and have never had a problem. I recently unplugged my DSL modem and this router to move them, and when I plugged them in again, the router stopped picking up the internet signal from the DSL modem. I'm able to get internet when I hardwire directly to the modem though. I tried resetting the router and setting the router up from scratch again, but now I just get error 321 Ethernet cable not connected when I try and run the setup cd.
View 6 Replies
View Related
Oct 22, 2011
The last time I had to reconfigure the connections it took me hours!My son had to wipe his desktop clean and reinstall everything. Now when he tried to connect to the internet we can't get a connection at all. My desktop is still working fine as well as the wireless laptops.What do we have to do to get him reconnected?
View 6 Replies
View Related
